Shuttle XH61V Quick Start Manual

XH61V Quick Guide

62R-XH61V0-0601 XH61V English.Spanish.Korean. Traditional Chinese.Japanese. French. German Quick Guide

__p

【

English

】

Jumper Settings

A. Begin Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

6. Close the metal load plate, lower the CPU socket lever and lock in place.

7. Spread thermal paste evenly on the CPU surface.

3. Place the slimline DVD drive in the rack and fasten it with the four screws from the sides.

Front Panel

F5F7

Back Panel

B4 B6

B12

B10

B11

Motherboard Illustration

B13

F1. Power Switch / Power LED

F2. HDD LED

F3. ODD and Front I/O Bay

F4. Slim ODD Bay

F5. USB2.0 Ports

F6. Mic-In

F7. Headphone

B1. S/PDIF Out Port

B2. Kensington® Lock Port

B3. COM1 Port (RS232/RS422/RS485)

B4. COM2 Port (RS232)

B5. DVI-I Port

B6. HDMI Port

B7. LAN Ports

B8. USB3.0 Ports

B9. USB2.0 Ports

B10. Mic-In Port

B11. Line-Out Port

B12. Line-In Port

B13. DC Power Port

Audio Connector

Pin Assignments (JP4):

1=MIC2_L 2=AGND 3=MIC2_R 4=FRONT-JD 5=LINE2-R 6=SENSE1_RETURN 7=FRONT_SENSE 8=KEY 9=LINE2-L 10=SENSE2_RETURN

Clear CMOS Jumper

Pin Assignments (JP10):

1=UL_BAT_PWR 2=-RTCRST 3=-RTCBTN

FAN Connectors

CUP_FAN/SYS_FAN

USB Headers

Pin Assignments (USB1/USB2/USB4):

1=5V_USB 2=5V_USB 3=USB A- 4=USB B 5=USB A+ 6=USB B+ 7=GND 8=GND 9=NC 10=NC

Support RS232 Back panel

PWM_CTRL

SPEED_SENSE

+12V

Ground

Power Connector

Pin Assignments (JP6):

1=+HD_LED 2=PWR_LED 3=-HD_LED 4=GND 5=RST_SW 6=PWR_SW 7=GND 8=GND 9=NC 10=KEY

Pin1-2

(BAT_POWER Mode)

SATA Power Connector

Pin Assignments (J1):

1=GND 2=GND 3=+5V 4=+5V

Independent External Power 12V / 5V

JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal. JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal. IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is +5V IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is +5V IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V

Pin Assignments (JP3):

1=-XRI1 2=COM_-XRI1 3=-XRI2 4=COM_-XRI2 5=+5V 6=+5V 7=COM1_PWR 8=COM2_PWR 9=+12V 10=+12V

2 4 6 8 10

1 3 5 7 9

Pin2-3

(Clear CMOS Mode)

1. Unscrew the two thumbscrews of the chassis cover.

2. Slide the cover backwards and upwards.

3. Unfasten the racks mount screws and remove the racks.

4 3 2 1

B. CPU and ICE Module Installation

1. Unfasten the four ICE module attachment screws.

HDD Rack

Rotating the fastener along the direction of arrow is to remove the ICE module, on the contrary, is to install.

2. Remove the ICE module from the chassis and put it aside.

Please note this 1155 pin socket bends easily. Always apply extreme care and little force when installing a CPU and limit the number of times you remove or exchange it. Before installation, make sure to turn off the computer and unplug the power cord from the mains to avoid damage.

ODD Rack

Metal load plate

Retention tab

Please do not apply excess amount of thermal paste.

8. Screw the ICE module to the mainboard. Note to press down on the opposite diagonal corner while tightening each screw.

Thermal Paste application area

Load lever

C. Memory Module Installation

1. Locate the SODIMM slot on the mainboard.

2. Align the notch of the memory module with the one of the memory slot.

notch

3. Gently insert the module into the slot in a 45-degree angle.

4. Carefully push down the memory module until it snaps into the locking mechanism.

45-degree

angle

SODIMM slot

4. Slide the rack downward and forward and refasten it using the two screws.

5. Connect the ODD cable and power cable to optical drive.

Slimline SATA Cable

6. Place the HDD in the rack and secure with the four screws from the side.

7. Connect the Serial ATA and power cables to the HDD.

Serial ATA Cable

8. Slide the rack in the chassis and refasten the two screws.

Serial ATA Power Cable

Follow the steps below to correctly install the CPU into the

motherboard CPU socket.

3. First unlock and raise the socket lever.

Latch

5. Repeat the above steps to install additional memory modules, if required.

Latch

Intel H61 Chipset

LAN (x1) & USB3.0 (x2) Ports

LAN (x1) & USB2.0 (x2) Ports

Mic-In/ Line-Out/ Line-In Ports

Clear CMOS Jumper-JP10

Audio Connector-JP4

USB Header-USB4

Serial ATA Connectors-SATA1,2,3

PCI-Express X4 Slot

LGA1155 Package CPU Socket

DVI-I & HDMI Ports

COM (x2) Ports

S/PDIF Out Port

ATX Power Connector-CN8

Support RS232 Back panel Independent External Power 12V/5V-JP3

TPM Header (LPC)-JP1

Mini PCIE Slot

Fan Connector-SYS_FAN

SATA Power Connector-J1

DDR3 SODIMM slots

USB Headers-USB1,USB2

Power Connector-JP6

Fan Connector-CPU_FAN

TPM Header (LPC)

Pin Assignments (JP1):

1=+12V 11=NC 2=5V 12=3VSB 3=5VSB 13=RI 4=SERIRQ 14=LDRQ 5=CLK-48M 15=PME 6=CLK-33M 16=LAD1 7=SIORST# 17=LAD0 8=LFRAME 18=+3.3V 9=LAD3 19=GND 10=LAD2 20=NC

Safety Information

Read the following precautions before setting up a Shuttle XPC.

CAUTION

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the manufacturer's instructions.

Laser compliance statement

The optical disc drive in this PC is a laser product.

The drive's classication label is located on the drive.

CLASS 1 LASER PRODUCT

CAUTION： INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

D. Component Installation

4. Lift the metal load plate on the CPU socket. Tear off the protective membrane from the bottom of ICE module. Remove the protective socket mylar from the CPU socket.

Remove the

protective

membrane

DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed.

5. Orientate the CPU and socket and please align the CPU notches with the socket alignment keys. Make sure the CPU is perfectly horizontal, insert it into the socket.

Triangle Pin1

Marking on the CPU

Notch on the CPU/

Alignment Key of the

CPU Socket

Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU!

The product’s color and specification will depend on the actual shipping product.

Socket

1155

CPU

Metal load plate

1. Install the Mini PCIE card into the Mini PCIE slot and screws

2. Untie all cables for easier installation.

Purse lock

secure with

E. Complete

1. Replace the cover and refasten the thumbscrews.

2 . Complete.

Please load the optimized BIOS settings.

53R-XH61V3-2001