Shuttle FT62 User Manual

FT62

Pentium 4/Celeron , 478-pin Processor

Based MAIN BOARD

Shuttle® FT62

Pentium 4/Celeron , 478-pin Processor Based Mainboard
Manual Version 1.0

Copyright

Copyright© 2003 by Shuttle® Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a retrieval system,

translated into any language, or transmitted in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without
prior written permission from Shuttle® Inc.

Disclaimer

Shuttle® Inc. shall not be liable for any incidental or consequential damages resulting from the
performance or use of this product.

This company makes no representations or warranties regarding the contents of this manual.
Information in this manual has been carefully checked for reliability; however, no guarantee is
given as to the correctness of the contents. In the interest of continued product improvement,
this company reserves the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to notify any
person of such revision or changes. The information contained in this manual is provided for
general use by the customers.

Trademarks

Shuttle is a registered trademark of Shuttle Inc.
Intel, Pentium is a registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.

General Notice: Other product names used in this manual are ascribed to their respective
owners and acknowledged.

M872

Statement of Shuttle Mainboard via the EMI Test

Shuttle mainboards have been via the EMI test in terms of series of regulations: EN55022/
CISPR22/AS/NZS3548 Class B, EN55024 (1998/AS/NZS), EN4252.1 (1994), EN61000, ANSI
C63.4 (1992), CFR47 Part 15 Subpart B, and CNS13438 (1997). The items tested are illus­trated as follows:

(A) Voltage: AC 110V/60HZ & AC 230V/50HZ
(B) Tested Product Information:

Product Name: PC Mainboard
Status: Sample
Model Name: FT62
S/N: N/A
CPU:

External Frequency: 100 MHz

Intel Pentium4: 1.6/ 1.8/ 2.0/2.2/2.4/2.6 GHz

External Frequency: 133 MHz

Intel Pentium4: 2.26/ 2.40/ 2.53/ 2.66/ 2.80/ 3.06 GHz

External Frequency: 200 MHz

Intel Pentium4: 2.8/ 3.0/ 3.2 GHz
Serial Port: one port with 9 pins
VGA Port: one port with 15 pins
Keyboard Port: one port with 6 pins
Mouse Port: one port with 6 pins
S-Video Port: one port with 7 pins
USB 2.0 Port: four ports with 4 pins respectively
1394a Port: two ports with 6 pins respectively
LAN Port: one port with 8 pins (10Mbps/100Mbps)
SPDIF-Out Port: one port for each
Mic-In & Rear-Out & Line-In Ports: one port for each
Center/Bass-Out Port: three ports
Reset Button: one button for each
DC-IN Power Connector: one port for each
DIMM Memory (optional): DDR 400 256 MB *2
Power Cable: Detachable and Shielded (with a GND pin)
Monitor: CRT
Maximum Resolution: 1280 X 1024 V:60Hz

All CPUs have completely been tested, and values offered by the worst EMI combination of
CPU external frequency are listed as follows:

Test Mode External Frequency CPU CPU Open/Close

1 133MHz P4 3.06 GHz Close
2 133MHz P4 3.06 GHz Open

3 200MHz P4 3.20 GHz Close
4 200MHz P4 3.20 GHz Open

(C) Remedy for the Tested Product & Its EMI Interference:

Remedy: N/A
EMI Interference:

Crystal: 24.576MHz(X4)/ 24.576MHz(X6)/ 25.00MHz(X7)/ 32.768KHz(X2)
Clock Generator: CLK1

(D) Supported Host Peripherals:

Host Peripheral Product Name Model Name S/N FCC ID

#1 Case FT62 N/A
#2 Power Supply PC32B180HR 030509011 D33032
#3 Maxtor HDD (40 GB) D740X-6L N/A 3902B975
#4 Shuttle Card R/W PC-12 N/A
#5 Pioneer DVD Player DVD-116 AAMS027197WL 3892D029

(E) Notices for Assembling Computers:

1. Cases should be made of iron or other metal that has good electric conductivity.

2. Cylinders in a case should be made of metal, and as having a mainboard mounted
in a case, make sure screws are all utilized and fastened on a mainboard.

3. An I/O shielding should be contacted with I/O metallic parts of a mainboard.

4. Cables should appropriately be arranged and fixed in a case. Follow instructions:

Ø Leave IDE cables not crossed upon CPU and SDRAM;
Ø Leave power cables minimum in length, and not crossed upon a mainboard;
Ø Leave CPU fan cables minimum in length, and not near CPU;
Ø Leave cables on panels and other spare cables tied in a computer case.

5. Make sure an EMI shielding attached to a case has properly been installed.

6. Make sure a 5.25" and screws are fastened to an EMI shielding.

7. Make sure a case is closely in contact with EMI connected points.

8. Make sure there is no cleft in a case which is not deformed.

9. Make sure a PCI door is bound to a case.

10. Make sure cables of other devices (fans or some others) are fixed in a case.

TABLE OF CONTENTS

WHAT'S IN THE MANUAL....................................................................5

Quick Reference............................................................................................... 5

About This Manual ........................................................................................... 5

1 INTRODUCTION ................................................................................ 6

1.1 TO DIFFERENT USERS ............................................................................. 6

FIRST-TIME DIY SYSTEM BUILDER............................................................ 6

EXPERIENCED DIY USER ........................................................................ 6

SYSTEM INTEGRATOR............................................................................... 6

1.2 ITEM CHECKLIST....................................................................................... 7

2 FEATURES ........................................................................................ 8

2.1 SPECIFICATIONS ....................................................................................... 8

3 HARDWARE INSTALLATION.......................................................... 11

3.1 STEP BY STEP INSTALLATION................................................................11

Accessories of FT62 ..............................................................................11

STEP 1 CPU Installation........................................................................ 12

STEP 2 Set Jumpers............................................................................. 13

STEP 3 Install DDR SDRAM System Memory........................................ 13

STEP 4 Install Internal Peripherals in System Case ................................ 14

STEP 5 Mount the Mainboard on the Computer Chassis........................ 15

STEP 6 Connect Front-Panel Switches/LEDs/Speaker/USBs................ 16

STEP 7 Connect IDE Disk Drives.......................................................... 17

STEP 8 Connect Other Internal Peripherals............................................ 17

STEP 9 Install Add-on Cards in Expansion Slots .................................... 19

STEP 10 Connect Power Supply ........................................................... 19

STEP 11 Connect External Peripherals to Back-panel ........................... 20

STEP 12 First Time System Boot Up..................................................... 21

STEP 13 Install Driver & Software Components..................................... 22

- 1 -

3.2 JUMPER SETTINGS ................................................................................. 23

JUMPERS & CONNECTORS GUIDE.................................................... 24

Jumpers

Clear CMOS Setting (JP1) ................................................................... 27

Back-Panel Connectors

DC-IN Power Connector ........................................................................ 28

VGA Connector ..................................................................................... 28

Clear CMOS button ............................................................................... 28

TV-Out Connector .................................................................................. 28

COM Port Connector ............................................................................. 28

SPDIF Out Port Connector..................................................................... 29

1394a Port Connectors ......................................................................... 29

LAN Port Connector .............................................................................. 29

USB Port 0/1 Connectors ...................................................................... 29

PS/2 Keyboard & PS/2 Mouse Connectors............................................ 29

Bass/Center-Out Port Connector ........................................................... 30

Rear-Out Port Connector ...................................................................... .30

Front-Out Port Connector....................................................................... 30

Front-Panel Connectors

ATX Power On/Off Switch Connector (PWON) ....................................... 31

Reset Button.......................................................................................... 31

Power LED............................................................................................ 31

HD LED ................................................................................................ 31

Mic-In Port Connector ............................................................................ 32

Line-In Port Connector ........................................................................... 32

Line-Out Port Connector ........................................................................ 32

USB Port 2/3 Connectors ...................................................................... 32

- 2 -

Internal Peripherals Connectors

Enhanced IDE ATA Connectors.............................................................. 33

Other Connectors

ATX Power Supply Connector (ATX1).................................................... 34

Fan Connectors (FAN1/2/3) ................................................................... 35

Wireless Keyboard and Mouse Connector (J3) ..................................... 35

AUXILIARY CD_IN Connector(J11) (White)............................................ 36

CD_IN Connector (J9) (Black) ............................................................... 36

SPDIF_In Header (J8) ........................................................................... 36

Parallel Port Header- EXT. Print Port (J6) .............................................. 37

IrDA Header (J7).................................................................................... 38

Extended USB Connector Headers (USB0, USB1)................................ 38

3.3 SYSTEM MEMORY CONFIGURATION ..................................................... 39

INSTALL MEMORY................................................................................ 39

UPGRADE MEMORY............................................................................ 39

4 SOFTWARE UTILITY ......................................................................40

4.1 Mainboard CD Overview ......................................................................... 40

4.2 Install Mainboard Software ..................................................................... 41

4.2.A Install ATI Chipset Driver ...................................................................... 42

4.2.B Install ATI VGA Driver ........................................................................... 42

4.2.C Install Realtek Audio Driver ................................................................. 43

4.2.D Install Realtek LAN Driver.................................................................... 43

4.2.E Install ATI USB2.0 Driver ...................................................................... 44

4.3 View the User's Manual........................................................................... 44

5 BIOS SETUP ...................................................................................45

5.1 Enter the BIOS .......................................................................................... 45

5.2 THE MAIN MENU ...................................................................................... 46

STANDARD CMOS FEATURES ............................................................... 48

- 3 -

ADVANCED BIOS FEATURES ................................................................. 51

ADVANCED CHIPSET FEATURES .......................................................... 54

INTEGRATED PERIPHERALS .................................................................. 58

POWER MANAGEMENT SETUP.............................................................. 61

PNP/PCI CONFIGURATIONS .................................................................... 64

PC HEALTH STATUS................................................................................ 66

LOAD FAIL-SAFE DEFAULTS .................................................................. 68

LOAD OPTIMIZED DEFAULTS ................................................................. 68

SET PASSWORD ..................................................................................... 68

SAVE & EXIT SETUP................................................................................ 69

EXIT WITHOUT SAVING ............................................................................ 69

- 4 -

WHAT'S IN THE MANUAL

Quick Reference

Hardware Installation >> Step-by-Step ................................................ Page 11

Jumper Settings >> A Closer Look.......................................................Page 23

Drivers/Software Utilities >> How to Install .........................................Page 40

BIOS Setup >> How to Configure.........................................................Page 45

About This Manual

For First-Time DIY System Builder.........................................................Page 6

For Experienced DIY User ...................................................................... Page 6

For System Integrator .............................................................................Page 6

- 5 -

1 INTRODUCTION

1.1 To Different Users

First-Time DIY System Builder

Welcome to the DIY world! Building your own computer system is not as diffi­cult as you may think. To make your first computer DIY experience successful,
right from the start, we have designed the 3.1 Hardware Installation section
in a step-by-step fashion for all the first-time DIY system builders. Prior to instal­lation, we also suggest you to read the whole manual carefully to gain a com­plete understanding of your new Shuttle FT62 mainboard.

Experienced DIY User

Congratulate on your purchase of the Shuttle FT62 mainboard. You will find
that installing your new Shuttle FT62 mainboard is just easy. Bundled with an
array of onboard functions, the highly-integrated FT62 mainboard provides you
with a total solution to build the most stable and reliable system. Refer to sec­tions 3.2 Jumper Settings and Chapter 4 Drivers/Software Utilities to
find out how to get the best out of your new mainboard. Chapter 5 BIOS
Setup also contains the relevant information on how to tune up your system to
achieve higher performance.

System Integrator

You have wisely chosen Shuttle FT62 to construct your system. Shuttle FT62
incorporates all the state-of-the-art technology of the RS300+IXP150 chipset
from ATI. It integrates the most advanced functions you can find to date in a
compact Small Form Factor ATX board.

- 6 -

1.2 Item Checklist

FAN2

9100 1GP

215RPS3AGA21H

J5

RTL8100C 32135S

1

311 TAIWA

N

ATX1

CA331057C

0330 - 014

Check all items with your FT62 mainboard to make sure nothing is missing.
The complete package should include:

- One piece of Shuttle FT62 Mainboard

- Three piece of ATA100/66/33 Ribbon Cable

- One piece of IDE Device Power Cable

AUDIO1

KB1

1

J3

J9

J11

J8

1

1

FAN3

SPDIF

FAN1

1

J6

PCI1

c AmMega 87-96

MGSKH1

1

J7

R

aoeon

JP1

1

IDE2

IDE1

G45744.1.W11

0330AA
TAIWAN

USB0

USB1

1

1

J2

ICS

9P750CF

DIMM1

DIMM2

- One S-Video to Composite/AV-Output Cable

- FT62 User's Manual

- One piece of Bundled CD-ROM with containing:
Ø FT62 user's manual saved in PDF format

Ø Install ATI Chipset Driver
Ø Install ATI VGA Driver
Ø Install Realtek Audio Driver
Ø Install Realtek Lan Driver
Ø Install ATI USB2.0 Driver
Ø Award Flashing Utility

- 7 -

2 FEATURES

FT62 mainboard is carefully designed for the demanding PC user who wants high perfor­mance and maximum intelligent features in a compact package.

2.1 Specifications

- CPU Support

Intel Pentium 4/Celeron, 478-pin support Northwood processor with 400/
533/800MHz FSB.

- Chipset

Features ATI RS300 N.B. and ATI IXP150 S.B..
Onboard Lan
RTL8100C support 10Mb/s and 100Mb/s operation.
Onboard 1394a
VIA VT6307, support 400Mb/s, 200Mb/s, or100Mb/s data transfer rate.

- Jumperless CPU Configuration

Soft-configuration FSB (The FSB speed is software configurable from (1MHz to
15MHz) of BIOS setup program.

- On Board 6 Channel AC97 Audio

Realtek ALC650 supports 18bits ADC and 20bits DAC resolution and 6
channel slot selectable DAC Output for multi-channel applications.
Compliant with AC'97 2.2 specifications.

- Versatile Memory Support

Features the dual-channel mode of 128 bit data transfer rate.
Two 184-pin DIMM slots to support up to 2GB of PC1600,PC2100, PC2700
or PC3200 compliant DDR SDRAM module.

- PCI Expansion Slot

Provides one 32-bit PCI slot.

- 6 USB 1.1/2.0 Complaint Interface Onboard

Ø 2 x USB ports on back-panel, 2 x USB ports on front-panel and one sets of

2 x USB port headers on mid-board.

- I/O Interface

Provides a variety of I/O interfaces:

Ø 1 x DC-IN connector.
Ø 1 x DB15 VGA connector.

- 8 -

Ø 1 x Clear CMOS button.
Ø 1 x AV & S-Video port.
Ø 1 x DB9 Serial port.
Ø 1 x SPDIF-out port.
Ø 2 x 1394a ports.
Ø 1 x RJ45 LAN port.
Ø 2 x USB 1.1/2.0 ports.
Ø 1 x PS/2 Mouse port.
Ø 1 x PS/2 Keyboard port.
Ø 1 x Bass/Center port.
Ø 1 x Rear-Out port.
Ø 1 x Front-Out port.

- PCI Bus Master IDE Controller Onboard

Two Ultra DMA 100/66/33 Bus Master Dual-channel IDE ports provide sup­port to a maximum of four IDE devices (one Master and one Slave per channel).
The IDE Bus implements data transfer speeds of up to 100/66/33 MB/sec and
also supports Enhanced PIO Modes.

80-pin Cable Backward Compatible Legacy ATAPI Devices, ATAPI IDE CD­ROM, CD-R, CD-RW, and LS-120 Supports.

- Advanced Configuration and Power Interface

Features four power saving modes: S1 (Snoop), S3 (Suspend to RAM), S4 (Sus­pend to DISK), and S5 (Soft-Off). ACPI provides more efficient Energy Saving
Features controlled by your operating system that supports OS Direct Power
Management (OSPM) functionality.

- System BIOS

Provides licensed Award BIOS V6.0 PG on 4Mb Flash core and supports Green
PC, Desktop Management Interface (DMI).

- Form Factor

System board conforms to Small from factor ATX specification.
Board dimension: 266mm x 170mm.

- Advanced Features

Ø Low EMI - Built in spread spectrum to reduce EMI.

- 9 -

Ø Dual Function Power Button - The system can be in one of two states,

one is Suspend mode and the other is Soft-Off mode. Pushing the power
button for less than 4 seconds places the system into Suspend mode.

When the power button is pressed for longer than 4 seconds, the system
enters Soft-Off mode.

Ø Modem Ring Power-On - The system can be powered on automatically

by the activation of modem ringing.

- Intelligent Features

Ø Voltage Monitoring - Monitors various voltages of key elements, such

as the CPU, and other critical system voltage levels to ensure stable
current passing through mainboard components.

Ø Fan Status Monitoring - To prevent CPU from overheating, the CPU fan

is monitored for RPM and failure. (CPU Cooling FAN with RPM sensor is
required.)

Ø Temperature Monitoring - This item allows users to make sure whether

the CPU or system runs in a suitable temperature.

Ø CPU Fan AutoGuardian - This SMART Bios enabled 3 phase Variable

Fan Speed and CPU temperature Control feature.

- 10 -

3 HARDWARE INSTALLATION

FAN2

R

aoeon

9100 1GP

215RPS3AGA21H

J5

RTL8100C 32135S

1

311 TAIWA

N

ATX1

CA331057C

0330 - 014

SPDIF

U
S
B
0

U
S
B
1

COM & SPDIF-out Ports

Center/Bass/Rear-Out/Front-Out Headers

LAN & USB 2.0 s

Port

VGA

& Clear CMOS & TV-out Ports

Mic-in/Line-in/Line-out Connectors

Before removing or installing any of these devices including CPU, DIMMs,
Add-On Cards, Cables, please make sure to unplug the onboard power
connector.

This section outlines how to install and configure your mainboard. Refer to the following
mainboard layout to help you to identify various jumpers, connectors, slots, and ports. Then
follow these steps designed to guide you through a quick and correct installation of your
system.

3.1 Step-by-Step Installation

Accessories Of FT62

CD_IN Connector-

J9

PS/2 Keyboard/Mouse s Port

Wireless KB/MS Connector-

Auxiliary CD-IN
Connector-

SPDIF IN­Fan Connector-

Fan Connector-

EXT. PRINT Port-

J11

J8

FAN1

FAN3

J6

One PCI Slot

SOCKET 478

IrDA Connector-

Clear CMOS­Two IDE Connectors

-

IDE1/IDE2

Extended USB 2.0
Headers-USB0,USB1

J7

JP1

1394a Ports

J3

AUDIO1

KB1

1

J3

J9

J8

IDE2

J11

1

1

FAN3

FAN1

1

J6

PCI1

c AmMega 87-96

MGSKH1

1

J7

JP1

1

G45744.1.W11

0330AA
TAIWAN

DC-IN Connector

ICS

9P750CF

Two 184-pin DDR

ATI RS300 Chipset

-ATX3

-SDRAM DIMM Sockets

-FAN2

ATI IXP150 Chipset
Reserved-

Power ON Connector-

ATX 12V/5V Connector­Reset Button

Power LED
HD LED

DIMM1

J2

J5

IDE1

1

1

J2

DIMM2

Fan Connector

USB 2.0 Connectors

ATX1

- 11 -

Step 1

CPU Installation:

This mainboard supports Intel Pentium 4/Celeron Socket 478 series CPU.
Please follow the steps as follows to finish CPU installation.

Note the CPU orientation when you plug it into CPU socket.

1. Pull up the CPU socket lever to 90-degree angle.

CPU socket lever up to
90-degree angle

2. Locate Pin 1 in the socket and look for a black dot or cut edge on the CPU
upper interface. Match Pin 1 and cut edge, and insert the CPU into the

socket.

CPU Pin 1 and cut edge

3. Press down the CPU socket lever and finish CPU installation.

Note: The CPU might be damaged if you

do not match the CPU socket Pin 1
and cut edge well.

4. Intel Pentium 4/Celeron processors require a set of heatsink and fan to cool
down the processor. You need to purchase a heatsink and fan if they are not
bundled with your CPU. Required is that install the set and plug its cable in
the CPU fan power connector. Note that there are kinds of CPU fan connec­tors. Normally, if your mainboard supports a hardware monitoring function,
a 3-pin fan power connector can have your system detect the CPU fan's spe­ed. A CPU fan with a 2-pin or 4-pin fan power connector does not support
the detection of the CPU fan's speed, and must directly be connected to the
system's power supply unit.

- 12 -

Step 2.

Set Jumpers

This mainboard is jumperless! The default jumper settings have been set for the
common usage standard of this mainboard. Therefore, you do not need to reset
the jumpers unless you require special adjustments as any of the following cases:

1. Clear CMOS

For first-time DIY system builders, we recommend that you do not change the
default jumper settings if you are not totally familiar with the mainboard con­figuration procedures. The factory-set default settings are tuned for optimum
system performance. For the advanced users who wish to customize their sys­tem, section 3.2 Jumper Settings will provide detailed information on how to
configure your mainboard manually.

Step 3

Install DDR SDRAM System Memory

To install memory, insert DDR SDRAM memory module(s) in DIMM slot(s).
Note that DDR SDRAM modules are directional and will not go in the DIMM
slots unless properly oriented. After the module is fully inserted into the DIMM
slots, lift the clips of both sides of the DIMM slot to lock the module in place.

DDR SDRAM

- 13 -

Step 4

Install Internal Peripherals in System Case

Before you install and connect the mainboard into your system case, we rec­ommend that you first assemble all the internal peripheral devices into the com­puter housing, including but not limited to the hard disk drive (IDE/HDD), CD­ROM drive, and ATX power supply unit. This will greatly facilitate in making
the connections to the mainboard described below.

To install IDE drives, follow this procedure:

1. Set the required jumpers on each device according to the instructions pro­vided by the manufacturer. (IDE devices, HDD, and CD-ROM, have to set
jumpers to Master or Slave mode depending on whether you install more
than one device of each kind.)

2. Connect IDE cable cable on the back-panel of the internal
peripheral devices to the corresponding headers on board.
Note that the cable should be oriented with its colored stripe (usually red or

magenta) connected to pin#1 both on the mainboard IDE connector and on
the device as well.

3. Connect an available power cable from your system power supply unit to
the back-panel of each peripheral device. Note that the power cable is
directional and cannot fit in if not properly positioned.

- 14 -

Step 5

Mount the Mainboard on the Computer Chassis

1. You may find that there are a lot of different mounting hole positions both on
your computer chassis and on the mainboard. To choose correct mounting
holes, the key point is to keep the back-panel of the mainboard in a close fit
with your system case, as shown below.

2. After deciding on the proper mounting holes, position the studs between the
frame of the chassis and the mainboard. The studs are used to fix the main­board and to keep a certain distance between the system's chassis and the
mainboard, in order to avoid any electrical shorts between the board and
the metal frame of the chassis. (If your computer case is already equipped
with mounting studs, you will need to tighten screws to attach the mainboard.)

Note : In most computer housings, you will be able to find 4 or more

attachment points to install mounting studs and then fix the main­board. If there aren't enough matching holes, then make sure to
install at least 4 mounting studs to ensure proper attachment of
the mainboard.

- 15 -

Step 6

758

Connect Front-Panel Switches/LEDs/Speaker/USBs

You are now ready to put the computer case back together and get on to the
external peripherals connections to your system's front-panel.

1

PWON

J5

1

1. ATX power on/off momentary type switch

2. Hardware reset switch

3. Power LED

4. IDE drive active LED

5. MIC-IN

6. Line-IN

7. Line-OUT

8. 2 USB 2.0/1.1 (2/3) Ports

2 3 4 6

- 16 -

Step 7

Connect IDE Disk Drives

IDE1

1. IDE cable connectors

Step 8

Connect Other Internal Peripherals

1. Wireless Keyboard and Mouse Connector (J3)

Wireless KB/MS

IDE2

1

1

1

J3

2. Auxiliary CD_IN Connector (J11)

CD_IN Connector (J9)

J11

Auxiliary CD-IN

- 17 -

1

1

J9CD-IN

3. SPDIF IN Port (J8)

4. Parallel port Header (J6)

SPDIF IN

J8

1

EXT. PRINT Port

5. IrDA Header (J7)

- 18 -

J6

1

IrDA Header

1

J7

6. DUAL USB Header (USB0, USB1)

CD-IN

USB1

USB0

Step 9

Install Add-on Cards in Expansion Slots

1. PCI Card

Step 10

Connect the Power Supply

1

1

1. System power connectors (ATX1/ATX3)

ATX12V/5V

ATX1

- 19 -

ATX3

1

Step 11

8

9

7

Connect External Peripherals to Back-Panel

You are now ready to put the computer case back together and get on to the
external peripherals connections to your system's back-panel.

1. DC-IN power connector

2. VGA Port (DB15 female)

3. Clear CMOS button

4. TV-Out Port (AV & S-Video)

5. Serial Port (DB9 male)

6. SPDIF-Out port

7. 1394a Ports

8. LAN Port

9. 2 USB 2.0/1.1 (0/1) Ports

10. PS/2 mouse Port

11. PS/2 keyboard Port

12. BASS/CENTER Port

13. Rear-OUT Port

14. Front-OUT Port

2 5

1 3 4 6

- 20 -

Step 12

First Time System Boot Up

To assure the completeness and correctness of your system installation, you
may check the above installation steps once again before you boot up your
system for the first time.

1. Turn on the system power then press "del" to enter BIOS.
Please set "CD-ROM" as the first boot device. Insert the operating system
setup CD disk into CD-ROM. Now you may save & exit the BIOS setup.
System will restart automatically.

2. After restart, just choose start computer with CD-ROM support.
Then the CD disk will bring up continuous message that teach you how to
get your HDD ready for operating system setup such as HDD partition
creation & format.

3. Once the C: disk's format is done, you can begin to install operating
system.

4. Setup the complete operating system according to your OS installation
guide.

- 21 -

Step 13

Install Drivers & Software Components

Please note that all the system utilities and drivers are designed for Win 9x/
2000/ME/XP/NT operating systems only. Make sure your operating system is
already installed before running the drivers installation CD-ROM programs.

1. Insert the FT62 bundled CD-ROM into your CD-ROM drive. The autorun

program will display the drivers main installation window on
screen.

2. Choose "Install ATI Chipset Driver" and complete it.

3. Choose "Install ATI VGA Driver" and complete it.

4. Choose "Install Realtek Audio Driver" and complete it.

5. Choose "Install Realtek LAN driver" and complete it.

6. Choose "Install ATI USB2.0 driver" and complete it.

7. Exit from the autorun drivers installation program.

] Please refer to section Chapter 4 Software Utility to install driver.

- 22 -

3.2 Jumper Settings

Several hardware settings are made through the use of jumper caps to connect
jumper pins to the mainboard. Pin #1 could be located at any corner of each
jumper; you just find a location marked with a while right angle, which stands
for pin1#. There are several types of pin 1# shown as below:

3-pin and multi-pin (>3) jumpers show as follows:

Pin #1 to the left:

Pin #1 on the top:

Pin #1 to the right:

Pin #1 on the bottom:

Jumpers with two pins are shown as for Close [On] or for Open
[Off]. To Short jumper pins, simply place a plastic jumper cap over the desired
pair of pins.

1

1

Caution!

1. Do not remove the mainboard from its antistatic protective packaging
until you are ready to install it.

2. Carefully hold the mainboard by its edges and avoid touching its
components. When putting the mainboard down, place it on the top
of its original packaging film and on an even surface, and components
side up.

3. Wear an antistatic wrist strap or take other suitable measures to prevent
electrostatic discharge (ESD) whenever handling this equipment.

- 23 -

Jumpers & Connectors Guide

B2~B4

B5~B6

E2D1C1

E1

E9C6C7C5C4C3C2

C8

Use the mainboard layout on page 11 to locate CPU socket, memory banks,
expansion slots, jumpers and connectors on the mainboard during the installa­tion. The following list will help you to identify jumpers, slots, and connectors
along with their assigned functions:

E3
E4

E6

E7

E2

E5

E8

B8~B9

B7

B1

A1

- 24 -

CPU/Memory/Expansion Slots

Socket478 : CPU Socket for Pentium 4/Celeron processors

DIMM1/2 : Two 184-pin DIMM Slots for 64,128, 256, 512 MB,

and 1GB of 2.5V DDR SDRAM
(The total installed memory does not exceed 2GB)

PCI : One 32-bit PCI Expansion Slot

Jumpers

A1

JP1 : Clear CMOS setting

Back Panel Connectors

B1
B2

B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14

DC-IN : DC-IN power connector

VGA : VGA Port (DB15 female)

Clear CMOS : Clear CMOS button

TV-Out : TV-Out Port (AV & S-Video)

COM : Serial Port (DB9 male) Port

SPDIF-Out : SPDIF-Out port

1394a : 2 x 1394a Ports

LAN : LAN Port

USB : 2 USB 2.0/1.1 (0/1) (Universal Serial Bus) Ports

MS : PS/2 mouse Port

KB : PS/2 keyboard Port

BASS/CENTER : Audio Bass/Center-Out Port

Rear-OUT : Audio Rear-Out Port

Front-OUT : Audio Front-Out Port

Front Panel Connectors

C1
C2
C3
C4
C5

PWON : ATX power on/off momentary type switch

Reset Button : Hardware reset switch

Power LED : Power LED

HD LED : IDE drive active LED

MIC-IN : Front panel audio port

- 25 -

C6

Line-IN : Front panel audio port

C7
C8

Line-OUT : Front panel audio port

USB : 2 USB 2.0/1.1 (2/3) (Universal Serial Bus) Ports

Internal Peripherals Connectors

D1
D1

IDE1 : IDE primary interface (Dual-channel)

IDE2 : IDE secondary interface (Dual-channel)

Other Connectors

E1
E2
E3

E4
E5
E6
E7
E8

E9

ATX1 : ATX 12V/5V Connector

FAN1/2/3 : Fan Connectors

J3 : Wireless Keyboard and Mouse Connector

J11 : Auxiliary CD_IN Connector

J9 : CD_IN Connector

J8 : SPDIF IN Port

J6 : Parallel port Header

J7 : IrDA Header

USB0, USB1 : Extended USB Connector Headers

- 26 -

F Jumpers

1

1

A1

Clear CMOS Setting (JP1)

JP1 is used to clear CMOS data. Clearing CMOS will result in the permanently
erasing previous system configuration settings and the restoring original(factory­set) system settings.

Pin 2-3 (Clear CMOS)

Pin 1-2 (Default)

Clear CMOS

1

JP1

Step 1. Turn off the system power (PC-> Off).

Step 2. Remove DC-IN(12V) Power cable from DC-IN Power connector.

Step 3. Remove jumper cap from JP1 pins 1-2.

Step 4. Place the jumper cap on JP1 pin 2-3 for a few seconds.

Step 5. Return the jumper cap to pin 1-2.

Step 6. Please wait for 2 seconds.

Step 7. Plug DC-IN Power cable into DC-IN Power connector.

Step 8. Turn on the system power (PC-> On).

- 27 -

F Back-Panel Connectors

B1

DC-IN Power Connector

This motherboard uses the 12V,
15Amp DC-IN power connector
that is 2x3.

B2

VGA Connector

One 15-pin VGA connector is
located at the rear panel of the
mainboard.

B3

Clear CMOS button

This button is used to clear
CMOS data.

DC-IN Connector

VGA Port

You can clear CMOS without
opening the chassis. It's a very
friendly button.

B4

TV-Out Connector

This mainboard can accom­modate AV and S Video ports
on back-panel.

B5

COM Port Connector

This mainboard can accom­modate two serial device on
COM. Attach a serial device
cable to the DB9 serial port
COM at the back-panel of
your computer.

Clear CMOS button

TV-Out Port

COM Port

- 28 -

B6

SPDIF Out Port Connector

SPDIF out connector can accept
digital audio data
from optic fiber.

B7

1394a Port Connectors

This mainboard offers two 1394a
ports on back-panel. Plug device
jack into an available 1394a con­nector.

B8

LAN Port Connector

This mainboard can accommodate
one device on LAN.
Attach a CAT-5 cable to the LAN
port at the back-panel of your
computer.

SPDIF Out Port

1394a Port

LAN Port

B9

USB Port 0/1 Connectors

Two female connectors USB0/1
share the same USB ( Universal
Serial Bus ) bracket at the rear
panel of your mainboard.
Plug each USB device jack into
an available USB0/USB1 con­nector.

B10

PS/2 Keyboard & PS/2 Mouse Connectors

B11

Two 6-pin female PS/2 key­board & Mouse connectors are
located at the rear panel of the
mainboard. Depending on the
computer housing you use
(desktop or tower), the PS/2
Mouse connector is situated at

USB Port 0/1

PS/2 Mouse

PS/2 keyboard

- 29 -

the top of the PS/2 Keyboard connector when the main-board is laid into a
desktop, as opposed to a tower where the PS/2 Mouse connector is located at
the right of the PS/2 Keyboard's. Plug the PS/2 keyboard and mouse jacks into
their corresponding connectors.

B12

Bass/Center Port Connector

Bass/Center-Out is a stereo
output port through which the
combined signal of all internal
and external audio sources on
the board is output. It can be
connected to 1/8-inch TRS ste­reo headphones or to bass/cen­ter amplified speakers.

B13

Rear-Out Port Connector

Line-In is a stereo line-level in­put port that accepts a 1/8-inch
TRS stereo plug. It can be used
as a source for digital sound re­cording, a source to be mixed
with the output, or both.

Bass/Center-Out Port

Rear-Out Port

B14

Front-Out Port Connector

Line-Out is a stereo output port
through which the combined
signal of all internal and exter­nal audio sources on the board
is output. It can be connected
to 1/8-inch TRS stereo head­phones or to amplified speak­ers.

Front-Out Port

- 30 -

F Front-Panel Connectors

PWON

C1

ATX Power On/Off Switch Connector (PWON)

The Power On/Off Switch is a momentary type
switch used for turning on or off the system
ATX power supply. Attach the connector
cable from the Power Switch to the 2-pin
(PWON) header on the mainboard.

C2

Reset Button

This switch allows you to reboot without having to power off the system. It is
also used for shutting down the system when <Ctrl><Alt><Del> does not
respond.

C3

Power LED

This LED will light when the system's power is on.

C4

HD LED

Reset Button

J5

Power LED

1

This LED will light when the hard drive is being accessed.

HD LED

- 31 -

C5

Mic-In Port Connector

This jack is used to connect an external microphone or output signals from
audio devices.

C6

Line-In Port Connector

Line-In is a stereo line-level input port that accepts a 1/8-inch TRS stereo plug.
It can be used as a source for digital sound recording, a source to be mixed with
the output, or both.

Mic-In Port

Line-In Port

Line-Out Port Connector

C7

Line-Out is a stereo output port through which the combined signal of all inter­nal and external audio sources on the board is output. It can be connected to 1/
8-inch TRS stereo headphones or to amplified speakers. Using this port dis­ables the front-out port at the rear panel.

C8

USB Port 2/3 Connectors

These ports allow connecting USB devices such as keyboard, pointing devices,
cameras, etc. connected in a series with data transfer rates up to 480Mb/sec­ond.

Rear-Out Port

USB Port 2/3

- 32 -

F Internal Peripherals Connectors

Enhanced IDE ATA Connectors

D1

The mainboard features two 40-pin dual-channel IDE device connectors (IDE1/
IDE2) providing support for up to four IDE devices, such as CD-ROM and Hard
Disk Drives (H.D.D.). Moreover, this mainboard comes with one 80-pin ATA
100/66/33 ribbon cable to connect to IDE H.D.D. connection.

IDE2

IDE1

1

1

Important : Ribbon cables are directional, therefore, make sure to

always connect with the red cable stripe on the same
side as pin #1 of the IDE1/IDE2 connector on the
mainboard.

- 33 -

F Other Connectors

ATX1

ATX1

E1

ATX Power Supply Connector (ATX1)

This motherboard uses 4-pin 12V/5V (ATX1) Pentium 4 standard ATX power
heade. Please make sure you plug in the right direction.

ATX12V/5V

1

Note1: The ATX power connector is directional and will not go in unless

the guides match perfectly making sure that pin#1 is properly po­sitioned.

Note2: Make sure the latch of the ATX power connector clicks into place

to ensure a solid attachment.

- 34 -

E2

1197531

12108642

Fan Connectors - FAN1/2/3

The mainboard provides three onboard 12V cooling fan power connectors
to support FAN1(Default System FAN), FAN2, FAN3 cooling fans.

SENSE

E3

Wireless Keyboard and Mouse Connector (J3)

Port J3 can be used to connect wireless keyboard and mouse device.
4 piece mini Jumpers must be setted on pin 5-6, 7-8, 9-10 and 11-12 when
this header is not used.

+12V

Note : Both cable wiring and type of plug may vary , which depends on the

GND

1

fan maker. Keep in mind that the red wire should always be conected
to the +12V header and the black wire to the ground (GND) header.

FAN1

FAN3

1

FAN2

1

1

Wireless KB/MS

1

J3

Pin Assignments:

1=VCC 2=VCC
3=GND 4=KEY
5=MSCLK 6=MS_CK
7=MSDATA 8=MS_DT
9=KBCLK 10=KB_CK

11=KBDATA 12=KB_DT

- 35 -

E4

AUX_IN

Left

GND

J11

432

1

CD_IN

GND

J9

432

1

J8

SPDIF

321

AUXILIARY CD_IN Connector (J11) (White)

E5

CD_IN Connector (J9) (Black)

Port J11 (White) and J9 (Black) can be used to connect a stereo audio input
from CD-ROM,TV-tuner or MPEG card.

J11

AUX_IN Right

E6

SPDIF_In Header (J8)

Port J8 can be used to connect special device.

Auxiliary CD-IN

CD_IN Right

1

1

J9CD-IN

Left

SPDIF IN

J8

1

Pin Assignments:

1=SPDIF IN

2=GND

3=VCC

- 36 -

E7

131211

10

Parallel Port Header-EXT. Print Port (J6)

One DB25 male parallel port header is located at the rear panel of the maiboard.
The header is used to connect the cable attached to parallel connector. But the
parallel cable is optional at the time of purchase.

26
25
24
23
22
21
20
19
18
17
16
15
14

9
8
7
6
5
4
3
2
1

EXT. PRINT Port

J6

1

Pin Assignments:

1=P_-STB 2=P_-PRD0 3=P_-PRD1

4=P_-PRD2 5=P_-PRD3 6=P_-PRD4

7=P_-PRD5 8=P_-PRD6 9=P_-PRD7

10=P_-ACK 11=P_-BUSY 12=P_-PE

13=P_-SLCT 14=P_-AFD 15=P_-ERR

16=P_-INIT 17=P_-SLIN 18=GND

19=GND 20=GND 21=GND

22=GND 23=GND 24=GND

25=GND 26=Key

- 37 -

IrDA Header (J7)

531

J7

12345

E8

If you have an infrared device, this mainboard can implement IrDA tranfer func­tion. To enable the IrDA transfer function, follow these steps:

Pin Assignment:

IrDA Header

1=NA 2=KEY

1

3=VCC 4=GND

J7

5=IrTx 6=IrRx

Note : Before connect your IR device, please be sure each IR on board pin

allocation is matchable with the pin of the IR device. Other wise,
incorrect IR connection may do damage to your IR device.

Step1 : Attach the 6-pin infrared device cable to J7.

(Refer to the above diagram for IR pin assignment.)

Step2 : This mainboard support IrDA, or Normal transfer modes.

E9

Extended USB Connector Headers (USB0, USB1)

The headers are used to connect the cable attached to USB connectors which
are mounted on front panel or back panel. But the USB cable is optional at the
time of purchase.

Pins Assignment:

USB1 USB0
1=GND 1=GND
2=GND 2=GND
3=Data5+ 3=Data4+
4=Data5- 4=Data4­5=VCC 5=VCC

- 38 -

USB1

1

USB0

1

3.3 System Memory Configuration

The FT62 mainboard has two 184-pin DIMM slots that allow you to install from
32MB up to 2GB of system memory. Each 184-pin DIMM (Dual In-line Memory
Module) Slot can accommodate 64MB, 128MB, 256MB, 512MB, and 1GB of
PC1600,PC2100, PC2700 or PC3200 compliant 2.5V single (1 Bank) or
double (2 Bank) side 64-bit wide data path DDR SDRAM modules.

Install Memory:

Install memory in any or all of the banks. The combination shown as follows.

Density Device Width Single/Double 184pin DDR DIMMs

4M x 16 SS / DS 32 / 64 MB

64 Mbit

8M x 8 SS / DS 64 / 128 MB

4M x 32 SS / DS 32 / 64 MB

128 Mbit

256 Mbit

512 Mbit

1024 Mbit

Note: Maximum installed memory is 2GB.

Note : You do not need to set any jumper to configure memory since the

BIOS utility can detect the system memory automatically.
You can check the total system memory value in the BIOS Standard
CMOS Setup menu.

8M x 16 SS / DS 64 / 128 MB

16M x 8 SS / DS 128 / 256 MB

8M x 32 SS / DS 64 / 128 MB

16M x 16 SS / DS 128 / 256 MB

32M x 8 SS / DS 256 / 512 MB

32M x 16 SS / DS 256 / 512 MB

64M x 8 SS / DS 512 / 1024 MB
64M x 16 SS / DS 512 / 1024 MB
128M x 8 SS / DS 1024 / 2048 MB

Upgrade Memory:

You can easily upgrade the system memory by inserting additional DDR SDRAM
modules in available DIMM slots. The total system memory is calculated by
simply adding up the memory in all DIMM slots. After upgrade, the new system
memory value will automatically be computed and displayed in the field " Stan­dard CMOS Setup" of BIOS setup program.

- 39 -

4 SOFTWARE UTILITY

4.1 Mainboard CD Overview

Note : The CD contents attached in FT62 mainboard are subject to change

without notice.

To start your mainboard CD disc, just insert it into your CD-ROM drive and
the CD AutoRun screen should appear. If the AutoRun screen does not appear,
double click or run D:\Autorun.exe (assuming that your CD-ROM drive is
drive D:)

Navigation Bar Description:

F Install Mainboard Software - Installing ATI Chipset Driver, ATI VGA

Driver, Realtek Audio Driver, Realtek LAN Driver, USB2.0 Driver.

F Install Utility - Installing Acrobat Reader, WinFlash Utility.

F Manual - FT62 Series mainboard user's manual in PDF format.

F Link to Shuttle Homepage - Link to shuttle website homepage.

F Browse this CD - Allows you to see contents of this CD.

F Quit - Close this CD.

- 40 -

4.2 Install Mainboard Software

Insert the attached CD into your CD-ROM drive and the CD AutoRun screen
should appear. If the AutoRun screen does not appear, double click on Autorun
icon in My Computer to bring up Shuttle Mainboard Software Setup
screen.

Select using your pointing device (e.g. mouse) on the "Install Mainboard
Software" bar to run into sub-menu.

The Mainboard Software include:

[4.2.A] Install ATI Chipset Driver

[4.2.B] Install ATI VGA Driver

[4.2.C] Install Realtek Audio Driver

[4.2.D] Install Realtek LAN driver

[4.2.E] Install ATI USB2.0 driver

- 41 -

4.2.A Install ATI Chipset Driver

Select using your pointing device (e.g. mouse) on the "Install ATI Chipset
Driver" bar to install ATI chipset driver.

Once you made your selection, a Setup window run the installation automati­cally. When the copying files is done, make sure you reboot the system to take
the installation effect.

4.2.B Install ATI VGA Driver

Select using your pointing device (e.g. mouse) on the "Install ATI VGA Driver"
bar to install ATI VGA Driver.

Once you made your selection, a Setup window run the installation automati­cally. When the copying files is done, make sure you reboot the system to take
the installation effect.

- 42 -

4.2.C Install Realtek Audio Driver

Select using your pointing device (e.g. mouse) on the "Install Realtek Audio
Driver" bar to install audio driver and AC'97 Sound System Software.

Once you made your selection, a Setup window run the installation automati­cally. When the copying files is done, make sure you reboot the system to take
the installation effect.

4.2.D Install Realtek LAN Driver

Select using your pointing device (e.g. mouse) on the "Install Realtek LAN
Driver" bar to install LAN driver.

Once you made your selection, a Setup window run the installation automati­cally. When the copying files is done, make sure you reboot the system to take
the installation effect.

Important: Under Win 98/Me, please check the "Read me" file and follow

steps for manual installation.

- 43 -

4.2.E Install ATI USB2.0 Driver

Insert the attached CD into your CD-ROM drive and the CD AutoRun screen
should appear. If the AutoRun screen does not appear, double click on Autorun
icon in My Computer to bring up Shuttle Mainboard Software Setup
screen. Select using your pointing device (e.g. mouse) on the “Install ATI
USB2.0 Driver” bar to install USB2.0 driver.

4.3 View the User's Manual

Insert the attached CD into your CD-ROM drive and the CD AutoRun screen
should appear. If the AutoRun screen does not appear, double click on AutoRun
icon in My Computer to bring up Shuttle Mainboard Software Setup
screen.

Select using your pointing device (e.g. mouse) on the “Manual" bar.
Then Online Information windows will appear on your screen. Click on the
“Install Acrobe Reader" bar if you need to install acrobe reader.

Then click on "Manual"
bar to view user's manual.

- 44 -

5 BIOS SETUP

FT62 BIOS ROM has a built-in Setup program that allows users to modify the
basic system configuration. This information is stored in battery-backed RAM
so that it retains the Setup information even if the system power is turned off.

The system BIOS is managing and executing a variety of hardware related func­tions in the system, including:

System date and time
Hardware execution sequence
Power management functions
Allocation of system resources

5.1 Enter the BIOS

To enter the BIOS (Basic Input / Output System) utility, follow these steps:

Step 1. Power on the computer, and the system will perform its

POST (Power-On Self Test) routine checks.

Step 2. Press <Del> key immediately, or at the following message:

Press DEL to enter SETUP, or simultaneously press <Ctrl>,
<Alt>, <Esc> keys

Note1. If you miss trains of words mentioned in step2 (the message dis-

appears before you can respond) and you still wish to enter BIOS
Setup, restart the system and try again by turning the computer
OFF and ON again or by pressing the <RESET> switch located
at the computer’s front-panel. You may also reboot by simulta­neously pressing the <Ctrl>,<Alt>, <Del> keys simulta­neously.

Note2. If you do not press the keys in time and system does not boot, the

screen will prompt an error message, and you will be given the
following options:

"Press F1 to Continue, DEL to Enter Setup”

Step 3. As you enter the BIOS program, the CMOS Setup Utility will

prompt you the Main Menu, as shown in the next section.

- 45 -

5.2 The Main Menu

Once you enter the AwardBIOS(tm) CMOS Setup Utility, the Main
Menu will appear on the screen. The Main Menu allows you to select
from several setup functions and two exit choices. Use the arrow keys
to select among the items and press <Enter> to accept and enter the
sub-menu.

Note that a brief description of each highlighted selection appears at the
bottom of the screen.

Setup Items

The main menu includes the following main setup categories. Recall
that some systems may not include all entries.

Standard CMOS Features

Use this menu for basic system configuration.

Advanced BIOS Features

Use this menu to set the Advanced Features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and opti­mize your system's performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management Setup

Use this menu to specify your settings for power management.

PnP / PCI Configurations

This entry appears if your system supports PnP / PCI.

- 46 -

PC Health Status

This entry shows the current system temperature, Voltage, and FAN
speed.

Load Fail-Safe Defaults

Use this menu to load the BIOS default values for the minimal/stable
performance of your system to operate.

Load Optimized Defaults

Use this menu to load the BIOS default values that are factory-set for
optimal performance system operation. While Award has designed the
custom BIOS to maximize performance, the factory has the right to
change these defaults to meet users' needs.

Set Supervisor / User Password

Use this menu to change, set, or disable password. It allows you to limit
access to the system and Setup, or only to Setup.

Save & Exit Setup

Save CMOS value changes in CMOS and exit from setup.

Exit Without Saving

Abandon all CMOS value changes and exit from setup.

- 47 -

@ Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into several
categories. Each category includes no, one or more than one setup
items. Use the arrow keys to highlight the item and then use the
<PgUp> or <PgDn> keys to select the value you want in each item.

Date

<Month> <DD> <YYYY>
Set the system date. Note that the 'Day' automatically changes when

you set the date.

Time

<HH : MM : SS>
The time is converted based on the 24-hour military-time clock. For

example, 5 p.m. is 17:00:00.

IDE Primary Master

Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.

IDE Primary Slave

Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.

IDE Secondary Master

Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.

- 48 -

IDE Secondary Slave

Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.

Video

Select the default video device.
Ø The choice: EGA/VGA, CGA 40, CGA 80, or MONO.

Halt On

Select the situation in which you want the BIOS to stop the POST
process and notify you.

Ø The choice: All Errors, No Errors, or All, But Keyboard.

Base Memory

Displays the amount of conventional memory detected during boot up.
Ø The choice: N/A.

Extended Memory

Displays the amount of extended memory detected during boot up.
Ø The choice: N/A.

Total Memory

Displays the total memory available in the system.
Ø The choice: N/A.

******************************************************

IDE Adapters

The IDE adapters control the hard disk drive. Use a separate sub-menu
to configure each hard disk drive.

IDE HDD Auto-Detection
Press <Enter> to auto-detect HDD on this channel. If detection is
successful, it fills the remaining fields on this menu.

Ø Press Enter

IDE Primary Master
Selecting 'manual' lets you set the remaining fields on this screen and
select the type of fixed disk. "User Type" will let you select the number
of cylinders, heads, etc., Note: PRECOMP=65535 means

NONE !

Ø The choice: None, Auto, or Manual.

- 49 -

Access Mode
Choose the access mode for this hard disk.

Ø The choice: CHS, LBA, Large, or Auto.

Capacity
Disk drive capacity (Approximated). Note that this size is usually
slightly greater than the size of a formatted disk given by a disk check­ing program.

Ø Auto-Display your disk drive size.

The following options are selectable only if the 'IDE Primary Master'
item is set to 'Manual', and Access mode set to CHS.

Cylinder
Set the number of cylinders for this hard disk.

Ø Min = 0, Max = 65535

Head
Set the number of read/write heads.

Ø Min = 0, Max = 255

Precomp
Warning: Setting a value of 65535 means no hard disk.

Ø Min = 0, Max = 65535

Landing zone
Set the Landing zone size.

Ø Min = 0, Max = 65535

Sector
Number of sector per track.

Ø Min = 0, Max = 255

******************************************************

- 50 -

@ Advanced BIOS Features

This section allows you to configure your system for basic operation.
You have the opportunity to select the system's default speed, boot-up
sequence, keyboard operation, shadowing, and security.

Hard Disk Boot Priority

This item allows you to select Hard Disk Book Device Priority.

Bios Write Protect

This item allows you to enable or disable the Bios Write Protect. If you
want to flash BIOS, you must set it Disabled.

Ø The choice: Enabled or Disabled.

Virus Warning

Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot
sector protection. If this function is enables and someone attempts to write
data into this area, BIOS will show a warning message on screen, and an
alarm beep.

Enabled Activates automatically when the system boots up,

causing a warning message to appear when anything
attempts to access the boot sector or hard disk
partition table.

Disabled No warning message will appear when anything

attempts to access the boot sector or hard disk
partition table.

Ø The choice: Enabled or Disabled.

- 51 -

CPU L1&L2&L3 Cache

All processors that can be installed in this mainboard use internal level1(L1)
, external 2(L2) cache memory and (L3) to imporve performance.

Leave this item at the default value for better performance.

Ø The choice: Enabled or Disabled.

Note: CPU support, L3 item appear.

Hyper-Threading Technology

The latest Intel application defines a high-speed calculating ability to
optimize your system by two CUPs supported(one virtual, one physical)
in a multi-task environment.

Ø The choice: Enabled, or Disabled.

Quick Power On Self Test

This item speeds up Power-On Self Test (POST) after you power on the
computer. If it is set to enabled, BIOS will shorten or skip some check
items during POST.

Ø The choice: Enabled, or Disabled.

First/Second/Third Boot Device

The BIOS attempts to load the operating system from the devices in the
sequence selected in these items.

Ø The Choice: LS120, Hard Disk, CDROM, ZIP100, USB-FDD,

USB-ZIP,USB-CDROM, LAN, or Disabled.

Boot Other Device

If BIOS can't load O.S. from First/Second/Third boot device you select
above, BIOS will search other devices and attempt to load O.S..

Ø The choice: Enabled or Disabled.

Boot Up NumLock Status

Selects power-on state for NumLock.

Ø The choice: Off or On.

Gate A20 Option

This entry allows you to select how the Gate A20 is handled. The gate
A20 is a device used for above 1MByte of address memory. Initially, the
gate A20 was handled via a pin on the keyboard. Today, while a key­board still provides this support, it is more common and much faster in
setting to fast for the system chipset to provide support for gate A20.

Ø The choice: Normal or Fast.

- 52 -

Typematic Rate Setting

Keystrokes repeat at a rate determined by the keyboard controller. When
this controller enabled, the typematic rate and typematic delay can be
selected.

Ø The choice: Enabled or Disabled.

Typematic Rate (Chars/Sec)

This item sets how many times the keystroke will be repeat in a second
when you hold the key down.

Ø The choice: 6, 8, 10, 12, 15, 20, 24, or 30.

Typematic Delay (Msec)

Sets the delay time after the key is held down before it begins to repeat the
keystroke.

Ø The choice: 250, 500, 750, or 1000.

Security Option

Select whether the password is required every time the system boots or
only when you enter setup.

System The system will not boot and access to Setup will be denied

if the correct password is not entered promptly.

Setup The system will boot, but access to Setup will be denied if the

correct password is not entered promptly.

Ø The choice: System or Setup.

Note : To disabled security, select PASSWORD SETTING at Main

Menu, and then you will be asked to enter password. Don't
type anything and just press <Enter>; it will disable security.
Once the security is disabled, the system will boot, and you
can enter Setup freely.

APIC Mode

Via the routing, I/O APIC support a total of 24 interrupts. "Enabled" for
Windows XP and Windows 2000 or Windows 2003.

Ø The choice: Enabled or Disabled.

MPS Version Control For OS

Selects the operating system multiprocessor support version.

Ø The choice: 1.1 or 1.4

- 53 -

OS Select For DRAM > 64MB

Selects the operating system that is running with greater than 64MB of
RAM in the system.

Ø The choice: Non-OS2 or OS2.

Small Logo<EPA> Show

This item allows you to enable or disable the EPA logo.

Ø The choice: Enabled or Disabled.

@ Advanced Chipset Features

This section allows you to configure the system based on the specific features
of the installed chipset. This chipset manages bus speeds and access to sys­tem memory resources, such as DRAM and the external cache. It also coor­dinates communications between the conventional ISA bus and the PCI bus.
It states that these items should never need to be altered. The default settings
have been chosen because they provide the best operating conditions for
your system. If you discovered that data was being lost while using your sys­tem, you might consider making any changes.

Warning: Over CPU DDR clock,voltage or timing(O.C) may damage

hardware. Strongly recommend to set only for expert.
Restore default setting to handle unstable system caused
by O.C .If O.C cause system boot fail, you must clear cmos
and load bios default setting to recovery system.

- 54 -

------ Now CPU Frequency -----

It shows current frequency of CPU Clock.

CPU Clock Ratio

This item allows the user to adjust CPU Clock Ratio.
If CPU is unlocked, item appear.

Ø The Choice: 8X~50X.

CPU FSB Clock

This item allows the user to adjust CPU FSB Clock.

Ø The Choice: Auto, 100MHz, 133MHz, 166MHz, 200MHz.

CPU Over Clock By

Ø The Choice: +0 ~ +15MHz.

CPU Voltage set

This item allows you to set CPU Voltage.

Ø The Choice: Auto, 0.8250V ~ 1.5875V.

Note: Over CPU voltage may damage CPU.

------ Now DDR Frequency -----

It shows current frequency of DDR Clock.

Memory Frequency For

This item allows the user to adjust Memory Frequency.
Ø The Choice: Auto, SYNC, DDR-200, DDR-266, DDR-333

or DDR-400.

DRAM Over Clock By

This item allows the user to fine tuning Memory Clock.

Ø The Choice: 0 ~ 15MHz.

Memory Timing Parameter

The value in this field depends on performance parameters of the installed
memory chips(DRAM). Don't change the value from the factory setting
unless you install new memory that has a different performance rating
than the original DRAMs.

Ø The Choice: Auto or Manual.

- 55 -

CAS Latency Time

When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Don't change this field from
the default value specified by the system designer.

Ø The Choice: 1, 1.5, 2, 2.5, 3, 3.5 or 4.

DRAM RAS# to CAS# Delay

This field lets you insert a timing delay between the CAS and RAS strobe
signals, and you can use it when DRAM is written to, read from, or re­freshed. Faster performance is gained in high speed, more stable perfor­mance, in low speed. This field is applied only when synchronous DRAM
is installed in the system.

Ø The Choice: 1, 2, 3 or 4.

DRAM RAS# Precharge

If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be-incompleted, and the
DRAM may fail to retain data. Fast gives faster performance; and Slow
gives more stable performance. This field is applied only when synchro­nous DRAM is installed in the system.

Ø The Choice: 1, 2, 3 or 4.

Active to Precharge Delay

The precharge time is the number of cycles it takes for DRAM to accumu­late its charge before refresh.

Ø The Choice: 1, 2, 3, 4, 5, 6, 7, or 8.

Memory Hole

You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it can't be cached. The user information of peripher­als that need to use this area of system memory usually discusses their
memory requirements.

Ø The Choice: Enabled or Disabled.

System BIOS Cacheable

Selecting Enabled allows caching of the system BIOS ROM at
F0000h~FFFFFh, resulting in better system performance. However, if any
program is written to this memory area, a system error may result.

Ø The Choice: Enabled or Disabled.

Spectrum Spreading Amount

This item allows you to set the spectrum spreading amount.
Ø The Choice : 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.50%, 1.75%,

or Disabled.

- 56 -

** On-Chip VGA Setting **
AGP Aperture Size

This item defines the size of the aperture if you use an AGP graphics
adapter. The AGP aperture refers to section of the PCI memory address
range used for graphics memory. We recommend that you leave this item
at the default value.

Ø The Choice: None,32MB, 64MB, 128MB, 256MB, 512MB, 1GB

or 2GB.

UMA Frame Buffer Size

This item is select UMA Frame Buffer Size.
It will be shared from system memory.
Ø The Choice: 8M,16M, 32M, 64M, or 128M.

Video Display Devices

You can select boot display device as CRT/TV.
Ø The Choice: Auto, CRT Only or TV Only.

TV Standard

You can select TV mode for Dos.
Ø The Choice: NTSC, PAL, NTSC-JAP or PAL-N.

- 57 -

@ Integrated Peripherals

SB200 OnChip IDE Device

Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
IDE DMA transfer access
Improve IDE HD/CDROM transfer performance.
Ø The choice: Enabled or Disabled.
OnChip IDE Channel 0/1
Use these items to enable or disable the PCI IDE channels that are inte-

grated on the mainboard.
Ø The choice: Enabled or Disabled.
IDE Prefetch Mode <Rd>/<Wrt>
The onboard IDE drive interfaces support IDE prefetching for faster drive

access. If you install a primary and/or secondary add-on IDE interface, set
this field to Disabled if the interface does not support prefetching.

Ø The choice: Enabled or Disabled.

Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmed Input/Output) items let you set a PIO mode
(0-4) for each of the four IDE devices. Modes 0 through 4 provide succes­sively increased performance. In Auto mode, the system automatically
determines the best mode for each device.

Ø The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, or Mode 4.
Primary/Secondary Master/Slave UDMA
If you install a device that supports UltraDMA that provides faster access

to IDE devices, change the item to Auto.
Ø The choice: Disabled or Auto.

- 58 -

IDE HDD Block Mode

Select Enabled for automatic detection of the optimal number of block
read/write per sector the drive can support.

Ø The Choice: Enabled or Disabled.

SB200 OnChip PCI Device

Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
Onboard AC97 Audio
This item allows you to control the onboard AC97 Audio.
Ø The Choice: Auto or Disabled.

SuperIO Device

Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
Onboard Serial Port1
This option is used to assign the I/O address and interrupt request ( IRQ )

for the onboard serial port1 ( COM1 ).
Ø The choice: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,

or Auto.
Onboard Infrared Port
This option is used to assign the I/O address and interrupt request ( IRQ )

for the onboard infrared port.
Ø The choice: Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,

or Auto.
UART Mode Select
This field is available if the Onboard Serial Port 2 field is set to any option

but disabled. UART Mode Select enables you to select the infrared com­munication protocol-Normal ( default ), IrDA, or ASKIR. IrDA is an infra­red communication protocol with a maximum baud rate up to 115.2K
bps. ASKIR is Sharp's infrared communication protocol with a maximum
baud rate up to 57.6K bps.

Ø The choice: SCR, IrDA, or ASKIR.
UR2 Duplex Mode
This item is available when UART 2 mode is set to either ASKIR or IrDA.

This item enables you to determin the infrared function of the onboard
infrared chip. The options are Full and Half ( default ).

Full-duplex means that you can transmit and send information simulta­neously. Half-duplex is the transmission of data in both directions, but
only one direction at a time.

Ø The choice: Full or Half.

- 59 -

Onboard Parallel Port
This item allows you to determine onboard parallel port controller I/O

address and interrupt request ( IRQ ).
Ø The choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, or Disabled.
Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port. Select

Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.

Ø The choice: SPP, EPP, ECP, or ECP+EPP.
ECP Mode Use DMA
When the onboard parallel is set to ECP mode, the parallel port can use

DMA3 or DMA1.
Ø The choice: 1 or 3.

Init Display First

This item allows you to decide to activate whether PCI slot or AGP first.
Ø The Choice: PCI Slot or Onboard.

USB Controller

Set "Enabled" for enable usb 1.1/2.0 controller and usb keyboard & mouse.
Ø The choice: Enabled or Disabled.

Onboard LAN Boot ROM

Decide whether to invoke the Boot ROM of the Onboard LAN chip.
Ø The choice: Disabled or Enabled.

- 60 -

@ Power Management Setup

The Power Management Setup allows you to configure your system to
most effectively saving energy while operating in a manner consistent
with your own style of computer use.

ACPI Function

This item allows you to enable/disable the Advanced Configuration and
Power Management (ACPI).

Ø Always "Enabled".

ACPI Suspend Type

This item allows you to select sleep state when suspend.
Ø The choice: S1(POS), S3(STR), or S1 & S3.

SpeedStep

SpeedStep only for mobile CPU.
Ø The choice: Enabled or Disabled.

Warning: SpeedStep "Enabled" only for Mobile CPU running on work
frequecy. DeskTop CPU strongly recommend set SpeedStep "Disabled".

Power Management Option

This item allows you to decide the timing to enter suspend mode.
Ø The choice: User Define, Min Saving, Max Saving.

HDD Power Down

When this item enabled and after the set up time of system inactivity,
the hard disk drive will be powered down while all other devices
remain active.

Ø The choice: Disabled or 1 Min~15 Min.

- 61 -

Video Off Option

When enabled, this feature allows the VGA adapter to operate in a
power-saving mode.

Always On Monitor will remain on during the power-

saving mode.

Suspend --> Off Monitor is blanked when the system enters

into the suspend mode.

Ø The choice: Always On or Suspend ->Off.

Video Off Method

This determines the manner in which the monitor is blanked.

V/H SYNC+Blank This selection will cause the system to turn off

the vertical and horizontal synchronization
ports and write blanks to the video buffer.

Blank Screen This option only writes blanks to the video

buffer.

DPMS Support Initial display power management signaling.

Ø The choice: V/H SYNC+Blank, DPMS Support, or Blank Screen.

MODEM Use IRQ

This determines the IRQ which the MODEM can use.
Ø The choice: 3, 4, 5, 7, 9, 10, 11, or NA.

Soft-Off by PWR-BTTN

Under ACPI you can create a software power down. In a software
power down, the system can be resumed by Wake UP Alarms. This
item lets you install a software power down that is controlled by the
power button on your system. If the item is set to Instant-Off, then the
power button causes a software power down. If the item is set to Delay4
Sec. then you have to hold the power button down for 4 seconds to
cause a software power down.

Ø The choice: Instant-Off or Delay 4 Sec.

Wake Up by PCI Card

This item Enabled/Disabled PCI Power Management Event to Wake Up
system. Set PCIPME wakeup systen from S1/S3/S4/S5.

Ø The choice: Enabled or Disabled.

Wake Up by Ring

This item determine the system will resume by activating of modem ring.
Set Moden Ring wakeup systen from S1/S3/S4/S5.

Ø The choice: Enabled or Disabled.

- 62 -

USB Wake up

If you are using a USB KB/MS, you can enable this item to allow a KB/
MS to wake up the system from power saving mode. Set Usb device
wakeup systen from S1/S3.

Ø The choice: Enabled or Disabled.

PS2 Keyboard Wake Up

This item allows you to set the PS2 Keyboard Wake Up function.
Set PS2 Keyboard Wake Up system from S3/S4/S5.

Ø The choice: Disabled, Password, or Hot KEY.

KB Wakeup Password

This item allows you to set the KB Wakeup Password.

Ø Press" Enter" to set Password.

Hot Key Wake Up

This item allows you to set the Hot Key Wake Up.

Ø The choice: Ctrl-F1~Ctrl-F12, or Any KEY.

PS2 Mouse Wake Up

This item allows you to enable or disable the PS2 Mouse Wake Up.
Set PS2 Mouse Wake Up system from S3/S4/S5.

Ø The choice: Disabled or Enabled.

Pwron After PWR-Fail

This item defines if the system will be rebooted after the power fails.

Ø The choice: Off, On, Former-Sts.

RTC Alarm Resume

When this item enabled, your can set the date and time at which the
RTC (real-time clock) alarm awakens the system from Suspend mode.

Ø The choice: Disabled or Enabled.

Data (of Month)

This item selects the alarm date.
Ø Key in a DEC number:Min=0, Max=31.

Resume Time (hh:mm:ss)

This item selects the alarm Time.
[hh]
Ø Key in a DEC number:Min=0, Max=23.
[mm/ss]
Ø Key in a DEC number:Min=0, Max=59.

- 63 -

@ PnP/PCI Configurations

This section describes the configuration of PCI bus system. PCI or
Personal Computer Interconnection is a system which allows I/O
devices to operate at the speed CPU itself keeps when CPU
communicating with its own special components.
This section covers some very technical items, and it is strongly
recommended that only experienced users should make any
changes to the default settings.

Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset
Extended System Configuration Data (ESCD) when you exit from Setup
if you have installed a new device or software and the system
reconfiguration has caused such a serious conflict that the operating
system can not boot.

Ø The choice: Enabled or Disabled .

Resource controlled By

The Award Plug-and-Play BIOS has the capacity to automatically
configure all of the boot and Plug-and-Play compatible devices.
However, this capability means absolutely nothing unless you are using
a Plug-and-Play operating system such as Windows 95.

If you set this field to "manual" , choose specific resources by going into
each of the sub-menu that follows this field (a sub-menu is proceeded
by a ">").

Ø The choice: Auto(ESCD) or Manual.

- 64 -

IRQ Resources

When resources are controlled manually, assign each system interrupt a
type, depending on the type of device using the interrupt.

IRQ3/4/5/7/10/11/12/14/15 assigned

This item allows you to determine the IRQ assigned to the ISA bus and
is not available to any PCI slot. Legacy ISA for devices is compliant with
the original PC AT bus specification; PCI/ISA PnP for devices is compli­ant with the Plug-and-Play standard whether designed for PCI or ISA
bus architecture.

Ø The choice: PCI Device or Reserved.

PCI/VGA Palette Snoop

It determines whether the MPEG ISA/VESA VGA Cards can work with
PCI/VGA or not. If you have MPEG ISA/VESA VGA Cards and PCI/
VGA Card worked, Enable this field. Otherwise, please Disable it.

Ø The choice: Enabled or Disabled.

Assign IRQ For VGA

The item aims at assigning the IRQ line to the VGA on your system.
When enabled, activity from the VGA will awaken the system.

Ø The choice: Disabled or Enabled.

Assign IRQ For USB

The item aims at assigning the IRQ line to the USB on your system.
When enabled, activity from the USB will awaken the system.

Ø The choice: Disabled or Enabled.

PCI Latency Timer <CLK>

Set the PCI Latency Timer.
Ø Min = 0, Max = 255

INT Pin1~4 Assignment

Names the interrupt request(IRQ) line assigned to a device connected to
the PCI interface on your system.

Ø The choice: Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.

- 65 -

@ PC Health Status

CPU Fan Speed Control

Set the CPU Fan Speed.
Ø The choice: Smart Fan, Ultra-Low, Low

Note : Before manually modifying the

, Mid , or Full .

CPU fan setting, please make
sure fan connectors are plug
into the correct fan connector
designations on the mainboard.

CPU Temperature below 80 oC , cpu fan speed 1900 rpm.

Ultra-Low

CPU Temperature over 80 oC , cpu fan speed 4000 rpm.
CPU Temperature below 80 oC , cpu fan speed 2500 rpm.

Low

CPU Temperature over 80 oC , cpu fan speed 4000 rpm.
CPU Temperature below 80 oC , cpu fan speed 3000 rpm.

Mid

CPU Temperature over 80 oC , cpu fan speed 4000 rpm.

Full CPU fan always 4000 rpm.

- 66 -

User Set CPU Fan

Enabled you to choose one specific fan for further setting.
Ø The choice: Fan1, Fan2, Fan3, Fan1 & Fan3.

CPU Temp Tag

The item only for 'smart fan' and you
can choose 'smart fan' on 'CPU Fan
Speed Control'. This feature ranges
from 30 0C to 80 0C, in an increment
of 1 0C. When CPU current tempera­ture over CPU Temp Tag (user set,
default value as 65 0C), CPU fan will
speed up. You can refer to table
below.

Ø The choice: Default 65 0C.

CPU Voltage
AGP Voltage
+3.3V
+5V
+12V

-12V
DDR Voltage
+5VSB
Voltage Battery
RS300 Temperature
CPU Temperature
PWM Temperature
Fan1 Speed
Fan2 Speed
Fan3 Speed

Warning :It is Strongly reco-mmended to

disable CPU Fan Auto Guardian
feature, if you wish to use other
fan cooler, allowing the fan to
run at its default speed.

- 67 -

@ Load Fail-Safe Defaults

When you press <Enter> on this item, you will get a confirmation
dialog box with a message similar to:

Load Fail-Safe Defaults (Y/N) ? N

Pressing 'Y' loads the BIOS default values for the most stable, minimal
performance system operations.

@ Load Optimized Defaults

When you press <Enter> on this item, you will get a confirmation
dialog box with a message similar to:

Load Optimized Defaults (Y/N) ? N

Pressing 'Y' loads the default values that are factory-set for optimal
performance system operation.

@ Set Supervisor/User Password

Steps to set supervisor/user password are described as follows:

- 68 -

New Password Setting:

1. While pressing <Enter> to set a password, a dialog box appears to

ask you enter a password.

2. Key in a new password. The password can not exceed eight charac-

ters.

3. System will request you to confirm the new password again.

4. When completed, new code takes effect.

No Password Setting:

If you want to disable the password, just press <Enter> as a password
input is requested.

If You Forget Password:

If you forget the password, the only way to access the system is to clear

the CMOS memory. Please refer to page 27 on clear CMOS setting.

@ Save & Exit Setup

Pressing <Enter> on this item asks for confirmation:

SAVE to CMOS and EXIT (Y/N)? Y

Pressing "Y" stores the selections made in the menus of CMOS - a
special section of memory that stays on after you turn your system off.
The next time you boot your computer, the BIOS configures your
system according to the Setup selections stored in CMOS. After saving
the values the system is restarted again.

@ Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit Without Saving (Y/N)? N

This allows you to exit from Setup without storing in CMOS any
change. The previous selections remain in effect. This exits from the
Setup utility and restarts your computer.

- 69 -