Page 1
SG41J1 Quick Guide
【
__p
English
】
Jumper Settings
A. Begin Installation
Note: For safety reasons, please ensure that the power cord is
disconnected before opening the case.
5. Spread an even layer of thermalcompound
on the CPU die.
4. Connect the Serial ATA and power cables to the HDD.
Front Panel
F1
F2
F4
F5
F6
F4
Back Panel
B11
B7
B1
B12
B2
B3
B11
B5
B4 B8
B6
Mainboard Illustration
Clear CMOS Button
LAN & USB2.0 (x2) Ports
Line-In/Line-Out/MIC Ports
B9
B10
B11
F3
F1. HDD LED
F2. Power Button / Power LED
F3. ODD Eject Button
F4. USB2.0 Ports
F5. Microphone
F6. Headphone
B1. AC Power Socket
B2. PS/2 Mouse Port
B3. PS/2 Keyboard Port
B4. DVI Port
B5. VGA Port
B6. USB2.0 Ports
B7. LAN Port
B8. Microphone-In Port
B9. Audio Line-Out Port
B10. Audio Line-In Port
B11. Wireless LAN Perforation
B12. Serial Port Preforation
DVI & VGA Port can not be used,
if a PCI Express graphics card is
installed.
USB2.0 (x2) Ports
VGA \DVI Port
PS/2 K/B & M/S Ports
Front Audio Header
C1
Pin Assignments (JP3):
1=MIC2_L
2=AGND
3=MIC2_R
4=FRONT-JD
5=LINE2-R
6=SENSE1_RETURN
7=FRONT_SENSE
8=KEY
9=LINE2-L
10=SENSE2_RETURN
C2
Front Panel Connector
Pin Assignments (JP2):
1=+HD_LED
2=PWR_LED
3=-HD_LED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NULL
10=KEY
FAN Connectors
C3
C4
AUX-IN Connector
4
3
2
1
C5
USB Header
Pin Assignments (USB1,2):
1=5V_USB 2=5V_USB
3=USB A- 4=USB B5=USB A+ 6=USB B+
7=GND 8=GND
9=KEY 10=NULL
C6
LPC HEADER
Pin Assignments (JP1):
1=+12V 2=5V 3=5VSB 4=SERIRQ
5=SIO48M 6=SIO_PCLK 7=SIORST 8=LFRAME
9=LAD3 10=LAD2 11=-12V 12=3VSB
13=NULL 14=LDRQ0 15=SIO_PME 16=LAD1
17=LAD0 18=+3.3V 19=GND 20=GND
(CPU_FAN1,SYS_FAN1)
4
3
2
1
11 12 13 14 15 16 17 18 19 20
Pin Assignments:
1=Ground
2=+12V
3=SPEED_SENSE
4=PWM_CTRL
Pin Assignments (
1=AUX-in-Left
2=Ground
3=Ground
4=AUX-in-Right
9 7 5 3 1
10
8 6 4 2
AUX_IN1
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and remove upwards.
Serial ATA Cable
Note: Please be sure to use an appropriate amount of heatsink
compound.
Serial ATA Power Cable
5. Connect the IDE Cable and power cables to the Optical Drive.
2
C. CPU Cooler Installation
1. Screw the Intel CPU FAN on to the mainboard and connect the fan
connector.
1
1
3. Unfasten the rack mount screws and remove the rack.
4
Fan Connector
3
Power Cable IDE Cable
2
Note: An COM / LPT ports bracket is available optionally from
Shuttle.
F. Expansion Card Installation
Note: Please refer to the user guide of the Intel CPU FAN you bought
to install the fan.
CPU cooler dimensions: 75 x75 x80 mm (Max.)
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
Note: Note: The maximum size for a graphics card to fit in the
chassis is 273mm x 98mm x 38mm
D. DDR memory module Installation
1. Unlock the DIMM latch.
B. CPU Installation
2. Align the DDR module’s cutout with the DIMM slot notch.
1. First unlock and raise the socket lever.
2. Lift the metal load plate on the CPU socket.
):
Note: This 775 pin socket is touch-sensitive and pins bend easily.
Always apply extreme care when installing a CPU and limit the
number of times that you remove or change the CPU.
2
1
3. Orientate the CPU and socket, aligning the yellow triangle on the
corner of the CPU with the triangle on the socket. Make sure the CPU
is perfectly horizontal, insert the CPU into the socket.
4. Remove the protective socket cover. Close the load plate, lower the
CPU socket lever and lock in place.
LGA775 Processor
Slide the DDR module into the DIMM slot.
Cutout
Notch
Latch Latch
3. Check that the latches are closed, and the DDR modules are firmly
installed.
Note: Repeat to install additional DDR modules if desired.
E. HDD and Optical Drive Installation
1. Place the HDD and optical drive in the rack and secure with screws
from the side.
PCI slot
PC I- Ex pre ss
x16 slot
Card PCB
2mm
2. Install the PCI/PCI Express x16 card (Optional) into the PCI/PCI Express
x16 slot.
42mm
Chassis
Cover
Card PCB
2mm
20mm
22mm
Chassis
Cover
C4
AUX-In1 Connector
C1
Front Audio
SYS_FAN Connector
C3
One PCI Express x16 Slot
C2
Front Panel
Serial ATA- SATA 1,2,3
USB
C5
Connector
ICH7 Chipset
BIOS Chip
Connector
One IDE Slot
Header
s- USB1, 2
One PCI
ATX Power Connector- ATX1
LGA775 Package CPU Socket
CPU_FAN Connector
Intel G41 Chipset
ITE 8718F Chipset
LPC Header
240 pins DDR DIMM (x2) Slots
ATX Power Connector- ATX2
C6
C3
1 2 3 4 5 6 7 8 9 10
Informations de sécurité
Lire les précautions d’usage avant l’installation d’un Shuttle XPC
ATTENTION
Ne pas replacer correctement la pile peut endommager l’ordinateur.
Remplacez uniquement par la même ou un équivalent comme recommandé par Shuttle.
Débarrassez-vous des piles usagées d’après les instructions du constructeur..
Etat de conformité du laser
Le lecteur de disque optique dans ce PC est un produit à laser.
Le label de classication du lecteur laser est situé sur le lecteur.
Produit laser de classe 1
Attention : Radiations laser à l’ouverture. Eviter l’exposition au faisceau laser.
[Français]
Safety Information
Read the following precautions carefully before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classication label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION：INVISIBLE LASER RADIATION WHEN OPEN.AVOIDEXPOSURETO BEAM.
Triangle Markings
Note: Failure to correctly align the CPU and socket can result in
damage to the CPU.
Lever
2. Place the rack in the chassis and refasten the rack.
3. Place the power cables in the rack clip located on the underside of the
rack mount. Then loosen the purse lock and separate the Optical Drive
power cable.
3. Secure the bracket.
G. Fixing the cover
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Note: Please load the optimized BIOS values.
The product’s actual color may vary from the product as shown in this guide.
L
53R-SG41J3-2001
Loading...