Shuttle DS47 Quick Start Manual
DS47 Quick Guide
__p
Front Panel
F1 F5
Back Panel
B2
B1 B6
F2 F3
F4
B3
【
F7
English
F1. USB2.0 Ports x4
F2. Power LED
F6
B7 B8B4 B5
F3. HDD LED
F4. Power Button
F5. COM 1 :
Support RS232/RS422/RS485
F6. COM 2 :
Support RS232
F7. SD Card Reader
】
B1. C-MOS Port
B2. DVI-I Port
B3. HDMI Port
B4. Mic-In
B5. Headphone
B6. USB3.0 Ports x2
B7. LAN Ports x2
B8. DC IN
62R-DS4700-4801
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
Intel
NM70 Chipset
®
Intel® Celeron® Processor 847
Motherboard Illustration Back
Super I/O
C10
Battery Connector
Pin Assignments (CN1):
1=V_BAT
2=GND
C12
Audio Connector
Pin Assignments
(Audio2):
1=PULL AGND
2=LINE-R
3=N/C
4=LINE-L
5=PULL AGND
6=FRONT_L
7=N/C
8=PRONT_SENSE
9=PULL AGND
10=FRONT_R
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.
1. Unscrew the two screws of the chassis cover.
11=BK_AUDIO-JD
12=MIC1_R
13=AGND
14=MIC1_L
13 11 9 7 5 3 1
14 12 10 8 6 4 2
C11
FAN2 connector
Pin Assignments:
1=-FANIO2
1
2=GND
3=FANPEM2
C13
CMOS Port
Pin Assignments (SW2):
1=PWRSW2=+5V
3=GND
4=Clear Cmos
1
2 4
1 3
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer's instructions.
C. Component Installation
1. As shown, unfasten the screw first. Install the Mini PCIe card
into the Mini PCIe slot and affix it with a screw.
Mini
PCIe slot
1
Screw
2
3
Left / Right Panel
Kensington® Lock Port
Motherboard Illustration Front
Panel Voltage
Select - JP3
Power Button - SW3
HDD LED
Power LED
USB 2.0 Ports x4
2.5 inch HDD slot
Mini PCIe Slot - CN3
LAN Ports x2
DC IN
USB 3.0 Ports x2
C11
Headphone
Mic In
C1
C2
Kensington® Lock Port
Converter Voltage Select - JP4
C3
Fan Connector - Fan1
C4
COM Port 1
COM Port 2
Power connector - SW1
C5
COM1&COM2
C6
Power Switch - JP2
C7
SMBUS
Mini PCIe slot with
mSATA support - PCIE1
LVDS Connector - LVDS1
C8
J1 AUTO PWR_SW
C9
Battery Connector - CN1
C10
Fan2 Connector
C11
DDR3 SODIMM slots
C12
Audio Connector - AUDIO2
DVI-I Port
C13
CMOS Port - SW2
HDMI Port
Panel Voltage Select
C1
Pin Assignments (JP3):
1=+3.3V
2=Panel_VDD
3=+5.0V
Power Button
C2
Pin Assignments (SW3)
C3
Converter Voltage Select
Pin Assignments (JP4):
1=+12V
2=INV_PWR_SRC
3=+5V
FAN_1 connector
C4
Pin Assignments (FAN1):
1=Ground
2=+12V
3=SPEED_SENSE
4=PWM_CTRL
Power Connector
C5
Pin Assignments (SW1):
1=+HD_LED
2=PWR_LED
3=-HD_LED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NUUL
3 1 2
1 2 3 4
1
3
5
7
9
Jumper Settings
C6
COM1&COM2 Power Switch
JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal.
3 1 2
2
4
6
8
JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V
Pin Assignments (JP2):
1=-XRI1 2=COM_-XRI1
3=-XRI2 4=COM_-XRI2
5=+5V 6=+5V
7=COM1_PWR 8=COM2_PWR
9=+12V 10=+12V
C7
SMBUS
Pin Assignments:
1=SMBCLK_SB
2=SMBDATA_SB
3=+5V
4=GND
C8
LVDS Connector
Pin Assignments (LVDS1):
1=N/C
2=Converter-PWR
3=N/C
4=Converter-PWR
5=N/C
6=Converter-PWR
7=GND
8=Converter-PWR
9=N/C
10=GND
31=LVDS_ACK_N
32=LVDS_BCK_N
33=GND
34=GND
35=LVDS_A2P
36=LVDS_B2P
37=LVDS_A2N
38=LVDS_B2N
39=GND
40=GND
C9
J1 AUTO PWR_SW
Pin Assignments:
SHORT=Disabled
OPEN=Enabled
1
11=GND
12=LVDS_DDAT
13=PWMO
14=LVDS_DCLK
15=GND
16=Panel_VDD
17=BKLTEN
18=Panel_VDD
19=PWMO
20=Panel_VDD
41=LVDS_A1P
42=LVDS_B1P
43=LVDS_A1N
44=LVDS_B1N
45=GND
46=GND
47=LVDS_A0P
48=LVDS_B0P
49=LVDS_A0N
50=LVDS_B0N
21=GND
22=GND
23=LVDS_A3P
24=LVDS_B3P
25=LVDS_A3N
26=LVDS_B3N
27=GND
28=GND
29=LVDS_ACK_P
30=LVDS_BCK_P
50
1
4 6 8 10
123 5 7 9
49
12
2. Slide the cover forwards and upwards.
2
1
B. Memory Module Installation
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
notch
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
1
2
45-degree
angle
3
Latch
5. Repeat the above steps to install additional memory modules, if required.
Latch
SODIMM slot
2. Unscrew the rack from the chassis.
3. Place the HDD in the rack and secure with the two screws from the side.
4. Put the HDD in the chassis and push toward right untill it inserts into the
SATA&SATA Power Connector.
5. Refasten the screw.
D. Complete
1. Replace the covers and refasten the screws.
2 . Complete.
Please load the optimized BIOS settings.
Operation Position:
1) Device must only be used in vertical position with the DVI
port facing up.
2) Please make sure to use either the supplied feet or the VESA
mount.
The product’s color and specification will depend on the actual shipping product.
L
53R-DS4703-1001
Loading...