Shurflo 135-0405-CG Installation Manual

INSTALLATION INSTRUCTIONS

Your new SHURflo Marine Grade Faucet will
give you years of trouble-free performance.
Thank you for choosing SHURflo Marine
Grade Faucets. Please read these instructions
carefully before installing your new faucet. If
you have any additional questions about the
installation of this faucet, please feel free to
contact one of our friendly customer service
representatives at 1-800-854-3218.

1

(1) Turn off the water supply to your existing faucet (this procedure will vary depending on the

specific plumbing system installed on your boat). Remove old shower set.

(2) Remove handle and wall plate from valve assembly. Remove the handle cap and handle screw.

Slide handle off the cartridge. Remove the two wall plate screws. Slide wall plate off the trim

2

sleeve. Make sure the wall plate gasket stays inside the back of the wall plate.

135-0405-CG

Pisces

Pressure Balanced

Single Handle Shower

Chrome/Gold

(3) From the back side of the bulkhead, slide the valve assembly through the hole in the bulkhead.

Note that the brass valve is stamped with “UP”. Make sure that the “UP” is on the top side when
positioned.

3

(4) Connect hot/cold water supply lines (not provided) to the inlet tubes. The inlet tubes are the 1/2”

NPT-Female tubes on the left and right sides of the valve. Wrap the fittings with Teflon
(Plumber’s) tape. This procedure will vary depending on the specific plumbing system installed on
your boat.

4

(5) Connect 1/2” NPT water line from the shower head or bulkhead elbow (not included) to the

shower head (top) port. Wrap the fitting on the water line with Teflon (Plumber’s) tape. Thread
tub port plug into the tub port (bottom) (if you are not using a tub spout with this installation).
Wrap the plug with Teflon (Plumber’s) tape.

5

(6) Replace handle and wall plate onto valve assembly. Slide wall plate back onto the trim sleeve

and insert the two screws. Be careful not to damage the wall plate gasket. Tighten the handle
screw and replace the handle cap. It may be necessary to secure the valve inside the wall to
prevent movement. This procedure will vary depending on the specific design of your boat.
Suggestions: Use the screw-holes molded into the valve. Use strapping material. Wedge item in
place.

6

(7) After installation is complete, turn the water supply back on and allow both hot and cold water to

run for at least one full minute. Make sure both shut-off valves are in the open position. While
water is running, check all connections for leaks. Connections may need re-tightening. You may
also want to adjust the max. temperature dials to allow for more or less hot water to pass.

135-0405-CG

Pisces

1

2

3

6

7

8

1) Handle Cap

2) Handle Screw

3) Pisces Handle

4) Wall Plate

5) Wall Plate Gasket

6) Wall Plate Screws

7) Retainer Ring

8) Trim Sleeve

9) Max. Temperature Dial A

4

10) Max. Temperature Dial B

11) Cartridge

5

12) O-Ring

13) Seat

14) Spring

15) Valve

16) Tub Port Plug

17) Shut-Off Valve

18) Shut-Off Valve Spring

19) Pressure Balance Housing

20) Pressure Balance Spool

Parts

From the galley to the head…
You can enjoy the entire Pisces
family throughout your boat!

Pressure Balanced

Single Handle Shower

Chrome/Gold

10

19

20

12

15

9

11

13

14

16

17

18

PROPER FINISH CARE:

Your new faucet is protected by a clear-coat. To clean it, you only need to wipe it with a damp, soft cloth. NEVER
use any abrasive cleaners, steel wool, or chemicals, as they will harm the finish and void your warranty. If the
faucet will be installed in a salt-air environment (boat exterior), regular cleaning with gentle soap and carnauba wax
will prolong the life of the finish.

LIMITED WARRANTY

SHURflo Marine Grade Faucets & Accessories are guaranteed to be free from material and workmanship defects under normal use and service for a period of
five (5) years from the date of purchase. This limited warranty will not apply to faucets or accessories that were improperly installed, misapplied, or
incompatible with components not manufactured by SHURflo. Faucet failure due to foreign debris is not covered under the terms of this limited warranty.
SHURflo will not warrant any faucet that is physically damaged or altered outside the SHURflo factory. Warranty claims may be resolved by a SHURflo
service center. All returns are to be shipped with charges pre-paid. Package all returns carefully. SHURflo will not be responsible for freight damage
incurred during shipping to a service center. SHURflo's obligation under this warranty policy is limited to the repair or replacement of the faucets &
accessories. Faucets or accessories found not defective (under the terms of this limited warranty) are subject to charges to be paid by the returnee for the
testing and packaging of "tested good" units. Warranty returns will be shipped on a freight allowed basis. SHURflo reserves the right to choose the method
of transportation. SHURflo is not responsible nor will it reimburse for labor necessary to remove and reinstall a faucet or accessory if found defective. This
warranty is only a representation of the complete Marine Products Limited Warranty outlined by Service Bulletin #1050.

SHURflo reserves the right to update specifications, prices, or make substitutions.

SHURflo*

5900-A Katella Ave.

Cypress, CA 90630

[phone] [phone]

FAX [phone]

Shipping: 5900-C Katella Ave.

Cypress, CA 90630

SHURflo East

52748 Park Six Court

Elkhart, IN 46514-5427

[phone] [phone]

FAX [phone]

http://www.shurflo.com

SHURflo Ltd.*

Unit 5 Sterling Park

Gatwick Road, Crawley

West Sussex, RH10 2QT

United Kingdom

[phone]

FAX [phone]

© 2004, SHURflo