Shurflo 133-0414-CG Installation Manual

INSTALLATION INSTRUCTIONS

Your new SHURflo Marine Grade Faucet will
give you years of trouble-free performance.
Thank you for choosing SHURflo Marine
Grade Faucets. Please read these instructions
carefully before installing your new faucet. If
you have any additional questions about the
installation of this faucet, please feel free to
contact one of our friendly customer service
representatives at 1-800-854-3218.

133-0414-CG

Pisces

Mini-Spread Faucet

Chrome/Gold

1

2

3

4

(1) Turn off the water supply to your existing faucet (this procedure will vary depending on the

specific plumbing system installed on your boat). Cover the sink drain to prevent any small
parts or debris from falling in. Remove your existing faucet, taking care not to damage your
existing water lines. Clean sink area in preparation for new faucet.

(2) Remove the lock nut (with screws), metal washer and rubber washer from both valves.

Wrap the male fittings on the connector hoses with Teflon (Plumber’s) tape and screw them
into the bottom of the valves. Use a wrench or pliers on the hex nut molded into the base of
the male fitting. Do NOT attempt to tighten by turning the hose itself. Place valves in sink
holes (both valves are identical, either one can be used for the left or the right side).
Position the escutcheon so that it aligns with the top thread of the valve body. From under
the sink, slide the rubber then metal washers onto the valves. Screw lock nuts onto the
valves (with the two screws pointing up) and hand tighten. Position valve on the sink and
tighten the lock nut screws with a screwdriver. CAUTION
SCREWS.

(3) Remove the Y connector, spout nut, metal spout washer and rubber spout washer from the

spout assembly. Line up the spout base and gasket with the bottom of the spout and set it
in the center hole of the sink. Lock the rubber and metal washers together and from under
the sink, slide them onto the shank and up against the bottom of the sink. Position spout
and secure with spout nut. Wrap both male fittings on the Y connector with Teflon
(Plumber’s) tape and attach it to the end of the spout shank. Connect female fittings on the
connector hoses to the Y connector.

: DO NOT OVER TIGHTEN

5

(4) Connect water supply lines (not provided) to the valve inlet tubes. Wrap the brass fittings on

the inlet tubes with Teflon (Plumber’s) tape. Follow the appropriate steps depending on
your water supply lines. If you have pre-assembled water supply hoses with threaded
connectors, simply screw on supply hose. If you have plastic water lines with formed ends,
water lines will seat partially up into the brass fittings. Connect by tightening the coupling
nuts. We do NOT suggest using sweat fittings as they are prone to blow-outs.

(5) After installation is complete, remove the aerator. Be careful not to scratch the finish. Turn

the water supply back on and allow both hot and cold water to run for at least one full
minute. While water is running, check all connections for leaks. Replace aerator.
Connections may need re-tightening.

133-0414-CG

Pisces

Mini-Spread Faucet

Parts

14

16

15

17

18

19

20

21

22

23

24

13

2

1) Handle Cap

1

2) Handle Screw

3) Pisces Handle

4) Retainer Nut

5) Escutcheon

6) Gasket

3

7) Ceramic Disc Cartridge

8) Valve

4

9) Rubber Washer

10) Metal Washer

5

11) Lock Nut

12) Lock Nut Screws

13) Connector Hose

6

14) Spout

15) Aerator

16) Lift-Rod Hole Plug

7

17) Spout Shank

18) O-Ring

19) Spout Base

20) Spout Base Gasket

8

21) Rubber Spout Washer

22) Metal Spout Washer

23) Spout Nut

24) Y Connector

From the galley to the head…
You can enjoy the entire Pisces
family throughout your boat!

Chrome/Gold

9

10

11

12

The matching optional

Pop-Up Drain kit with

lift-rod is available

through your retailer.

Ask for 131-0419-CG

PROPER FINISH CARE:

Your new faucet is protected by a clear-coat. To clean it, you only need to wipe it with a damp, soft cloth. NEVER
use any abrasive cleaners, steel wool, or chemicals, as they will harm the finish and void your warranty. If the
faucet will be installed in a salt-air environment (boat exterior), regular cleaning with gentle soap and carnauba wax
will prolong the life of the finish.

LIMITED WARRANTY

SHURflo Marine Grade Faucets & Accessories are guaranteed to be free from material and workmanship defects under normal use and service for a period of
five (5) years from the date of purchase. This limited warranty will not apply to faucets or accessories that were improperly installed, misapplied, or
incompatible with components not manufactured by SHURflo. Faucet failure due to foreign debris is not covered under the terms of this limited warranty.
SHURflo will not warrant any faucet that is physically damaged or altered outside the SHURflo factory. Warranty claims may be resolved by a SHURflo
service center. All returns are to be shipped with charges pre-paid. Package all returns carefully. SHURflo will not be responsible for freight damage
incurred during shipping to a service center. SHURflo's obligation under this warranty policy is limited to the repair or replacement of the faucets &
accessories. Faucets or accessories found not defective (under the terms of this limited warranty) are subject to charges to be paid by the returnee for the
testing and packaging of "tested good" units. Warranty returns will be shipped on a freight allowed basis. SHURflo reserves the right to choose the method
of transportation. SHURflo is not responsible nor will it reimburse for labor necessary to remove and reinstall a faucet or accessory if found defective. This
warranty is only a representation of the complete Marine Products Limited Warranty outlined by Service Bulletin #1050.

SHURflo reserves the right to update specifications, prices, or make substitutions.

SHURflo*

5900-A Katella Ave.

Cypress, CA 90630

[phone] [phone]

FAX [phone]

Shipping: 5900-C Katella Ave.

Cypress, CA 90630

SHURflo East

52748 Park Six Court

Elkhart, IN 46514-5427

[phone] [phone]

FAX [phone]

http://www.shurflo.com

SHURflo Ltd.*

Unit 5 Sterling Park

Gatwick Road, Crawley

West Sussex, RH10 2QT

United Kingdom

[phone]

FAX [phone]

© 2004, SHURflo