Shurflo 132-0103-CP Installation Manual
INSTALLATION INSTRUCTIONS
OEM Version
Attention Manufacturers
Please include this Installation
Instruction sheet with your Owner’s
Documentation.
(1) Turn off the water supply to your existing faucet (this procedure will vary depending on the specific
1
plumbing system installed on your boat). Cover the sink drain to prevent any small parts or debris
from falling in. Remove your existing faucet, taking care not to damage your existing water lines.
Clean sink area in preparation for new faucet.
(2) Place the faucet in the center hole of the sink. Pull the flex hose all the way up until the hose
2
stops. Slide the black rubber washer and then the metal washer onto the mounting shaft. Screw
the brass lock nut on mounting shaft with the two screws pointing up, as illustrated. Hand tighten
the brass lock nut. Position the faucet on the sink and tighten the lock nut screws with a
screwdriver. CAUTION: DO NOT OVER TIGHTEN THE SCREWS.
:
132-0103-CP
Stasis
Pull-Out Galley Faucet
Chrome
(3) Very gently bend the copper water inlet tubes slightly out, to allow for larger hose clearance.
4
5
6
7
CAUTION: USE CARE WHEN BENDING THE TUBES. Grip at point of bend with one hand and
adjust with the other.
(4) Screw the pipe adapter onto the flex hose. Use Teflon tape on threads. Hold the hose tightly
while turning the adapter. Do not allow hose to twist as it my kink. Push the pipe adapter onto the
third copper pipe with the male fitting, until you feel it “snap” into place. You may need to slightly
rotate the adapter side to side while pushing it on. Tighten the pipe adapter screw to secure. The
pipe adapter screw should screw completely in. Pipe adapter may rotate after connection is
secure. Ensure water supply lines do not interfere with flex hose.
(5) Attach metal weight to hose. Adjust position as desired. Weight must be installed to prevent hose
kinking and for easy hose return.
(6) Connect water supply lines (not provided) to the connector hoses. Wrap the brass fittings on the
connector hoses with Teflon (Plumber’s) tape. Follow the appropriate steps depending on your
water supply lines. If you have pre-assembled water supply hoses with threaded connectors,
simply screw on supply hose. If you have plastic water lines with formed ends, water lines will seat
partially up into the brass fittings. Connect by tightening the coupling nuts. We do NOT suggest
using sweat fittings as they are prone to blow-outs.
(7) Unscrew the spout head from the flex hose. Turn the water supplies back on and allow both hot
and cold water to run for at least one full minute. While water is running, check all connections for
leaks. Replace the spout head. Connections may need re-tightening
132-0103-CP
Stasis
3
2
1
4
5
6
11
7
1) Blue/Red Cap
2) Handle Screw
3) Handle
4) Cap
5) Retainer Ring
6) Cover
7) Ceramic Disc Cartridge
8) Packing Ring
9) Spout Hub
Parts
2
1/8
"
10) Hose Nest
8
9
10
11) Spout Head
12) Valve Body
13) O-Ring
14) O-Ring
15) Internal Vacuum Breaker
12
13
14
16
17
18
19
20
22
24
25
27
28
26
29
15
21
23
30
16) Packing Ring
17) Base Ring
18) Gasket
19) Hose Guide
20) Rubber Washer
21) Metal Washer
22) Lock Nut
23) Lock Nut Screws
24) Mounting Shaft
25) Pipe Adaptor O-Ring
26) Pipe Adaptor
27) Pipe Adaptor Screw
28) Pipe Adapter Washer
29) Flex Hose
30) Weight & Screws
4
1
/8
"
6
1
/4
"
8
1
/4
"
1
/2
"-14 NPSM
Pull-Out Galley Faucet
Chrome
7
1/2
"
6
3/4
"
7"
5"
8
1
/8
"2
1
/8
"
PROPER FINISH CARE:
Your new faucet is protected by a clear-coat. To clean it, you only need to wipe it with a damp, soft cloth. NEVER
use any abrasive cleaners, steel wool, or chemicals, as they will harm the finish and void your warranty. If the
faucet will be installed in a salt-air environment (boat exterior), regular cleaning with gentle soap and carnauba wax
will prolong the life of the finish.
LIMITED WARRANTY
SHURflo Marine Grade Faucets & Accessories are guaranteed to be free from material and workmanship defects under normal use and service for a
period of three (3) years from the date of manufactured vessel for all indoor applications and two (2) years from the date of manufactured vessel for all
outdoor applications. This limited warranty will not apply to faucets or accessories that were improperly installed, misapplied, or incompatible with
components not manufactured by SHURflo. Faucet failure due to foreign debris is not covered under the terms of this limited warranty. SHURflo
will not warrant any faucet that is physically damaged, or altered outside the SHURflo factory. Warranty claims may be resolved by a SHURflo
service center. All returns are to be shipped with charges pre-paid. Package all returns carefully. SHURflo will not be responsible for freight
damage incurred during shipping to a service center. SHURflo's obligation under this warranty policy is limited to the repair or replacement of the
faucets & accessories. Faucets or accessories found not defective (under the terms of this limited warranty) are subject to charges to be paid by the
returnee for the testing and packaging of "tested good" units. Warranty returns will be shipped on a freight allowed basis. SHURflo reserves the
right to choose the method of transportation. SHURflo is not responsible nor will it reimburse for labor necessary to remove and reinstall a faucet or
accessory, if found defective. This warranty is only a representation of the complete Marine Products Limited Warranty outlined by Service Bulletin #1050.
SHURflo reserves the right to update specifications, prices, or make substitutions.
SHURflo*
5900-A Katella Ave.
Cypress, CA 90630
(562) 795-5200 (800) 854-3218
FAX (562) 795-7564
Shipping: 5900-C Katella Ave.
Cypress, CA 90630
(574) 262-0478 (800) 762-8094
SHURflo East
52748 Park Six Court
Elkhart, IN 46514-5427
FAX (574) 264-2169
http://www.shurflo.com
SHURflo Ltd.*
Unit 5 Sterling Park
Gatwick Road, Crawley
West Sussex, RH10 2QT
United Kingdom
+44 1293 424000
FAX +44 1293 421880
911-xxx-132-0103-CP
Rev. 4/04
© 2004, SHURflo
Loading...