Shure orporated AXT610 Users manual

AXT610 Showlink Wireless Access Point

DRAFT

The AXT610 ShowLink wireless access point delivers real-time wireless control of the Axient transmitters. The access point uses
the 2.4 GHz spectrum to relay parameter changes made at the receiver or in Wireless Workbench 6 to the transmitter. All parameter
changes occur instantly without interrupting the performer.

A single access point can support up to 16 transmitters. Multiple access points can be used to extend the control range or increase
transmitter capacity.

Showlink 2.4 GHz Detachable

Antenna

Features





PUSH

Showlink Data Status LED

Power Status LED

Ethernet Status LED

Threaded mounting point

External Power Supply Connector

Axient Wireless

Showlink Acces Point

  



Reset Settings Button

Ethernet Port

AXT610





 Scanning Antenna for Channel

Agility

• Real-time wireless control of transmitters - make parameter changes
without interrupting performers

• Simple interface - LEDs instantly show the health of the Showlink
connection, Ethernet data, and the power supply

• High transmitter capacity - control 16 transmitters with a single access
point

• Build an expandable network - increase capacity and coverage by
adding more access points to the network

• Convenient power options - uses power over Ethernet (PoE) supplied
by other Axient components for fewer cables

• Expanded coverage range - coverage range is equal to the
broadcasting range of the transmitters

• Automatic network addressing - DHCP IP addressing automatically
configures the network address

• Reliable performance - the access point uses channel agility to scan
and monitor the quality of the 2.4 GHz communication channel.
If channel quality deteriorates, the access point automatically switches
to a clear frequency

• Remote monitoring - remotely monitor access point status and change
settings using Wireless Workbench (WWB) software

Included Accessories

• WA371 wireless microphone clip for mounting on a mic stand

• Euro thread adapter for WA371

• C825 shielded 25-foot Ethernet cable for ShowLink access point, RJ45 to EtherCon connector

Revision: 1.3 (12/21/10)

1

Showlink Basics

PUSH

DRAFT

ShowLink Channels and 2.4 GHz Spectrum

ShowLink channels that enable remote control of Axient transmitters operate in the 2.40 to 2.484 GHz portion of the RF spectrum in accordance with
the IEEE 802.15.4 protocol. Within the 2.4 GHz spectrum, 16 channels are available for ShowLink communication.

Available spectrum, low interference, and global availability make the 2.4 GHz spectrum an ideal choice for hosting ShowLink channels. Devices that
share the 2.4 GHZ spectrum, including Wi-Fi, are manufactured to efficiently share the spectrum and cause minimal interference.

To ensure reliable communication, the access point contains an internal scanning radio that analyzes the 2.4 GHz spectrum hundreds of times per
second. If interference is detected, the access point uses channel agility to automatically switch to a clear channel within the spectrum. All transmitters
associated with the access point will continue to communicate uninterrupted on the new ShowLink channel.

Transmitter Capacity

A single access point supports up to 16 transmitters. Any transmitter
within range of an active access point with available capacity will be
automatically controlled by that access point. When multiple access
points are used to increase transmitter capacity or increase coverage
range, the network will automatically divide transmitter control between
each access point. All changes in control between access points occur
seamlessly and automatically, without requiring user intervention.

Power

Power Over Ethernet

The Shure Ethernet switch and Axient rack components offer
Power over Ethernet (PoE) enabled network ports. When the
access point is connected to a PoE enabled network port using
a CAT 5E shielded Ethernet cable, power will automatically be
supplied as long as the host component is powered on.

External Power Supply (Optional)

If power over Ethernet (PoE) is not available, an external power
source supplying 15VDC ±10% (250mA) can power the access point.

1. Connect the power source to the external power supply jack.

2. Tighten the locking ring to secure the plug.

3. Plug the power supply AC line cord into an AC power source.

4. Connect a CAT 5E shielded Ethernet cable to the access point.

Coverage Area

The coverage area of the access point matches the transmitter’s RF
range. Use the ShowLink Test feature in the receiver menu to map
the boundaries of the coverage area. Multiple access points can be
used to increase the coverage area or expand coverage to multiple
rooms.

2.4 GHz Command Channel Agility

If the access point experiences interference from Wi-Fi or other
devices sharing the spectrum, channel agility automatically switches
to a clear channel.

PUSH

External Power

Supply Jack

Ethernet
Port

Networking

Networking the access point using a Shure Ethernet switch or a DHCP enabled router automatically assigns an IP address, simplifying
network setup. The network connection allows the access point to share data with networked Axient components and enables wireless
control of the transmitters.

Reset Option

Pressing the reset button located on the bottom of the housing
restores the access point to the following settings:

• IP Address Mode = DHCP

• Channel Agility = Enabled

• Device ID = AXT610

• All associated transmitters will be cleared

• Channel Mask = All frequency exclusions will be cleared

Revision: 1.3 (12/21/10)

2

Reset Button