Shure X100E User Manual

222

HARTREY

AVE..

EVANSTON.

AREA

CODE

3121866.2200

TWX: 910.231-0048

THE

PREMIER FAMILY OF STEREO SOUND REPRODUCERS

CABLE

IL.

60204 U.S.A.

SHUREMICRO

TELEX:

72.4381

MODEL

X100E

STEREO

DYNETIC@

PHONOGRAPH CARTRIDGE

CARTRIDGE AND

N75EC 10 X 18p (.OW4 .0007 in.) Biradial (Elliptical)

N75-3t

microns

(.0025 in.)

Spher~cal

toptlonal 78 rpm Stylus:

*Output voltage5 glven for stereo cut record For MONO cut record,

output vollagc at both left channel and rlght channel cartrldge

will

'"lracking forces greater than maxlmum lnd~cated should not be used

NET WEIGHT: 6.2 grdnls INDUCTANCE: DC RESISTANCE: 630 ohms

OPTIMUM farads total ohms with almost no audible change in frequency response. Total capacitance includes both tone arm wiring and amplifier input circuit.

FOUR-CHANNEL: This Stereo Dynetic@ cartridge is compatible with all four-channel matrix systems.

MONOPHONIC OPERATION: Set function switch on amplifier to "MONO" or right channels in parallel.

CONNECTIONS (see Figure ground (usually green) to "RG left ground (usually blue) to "LC." If metal head is causing ground loop hum, remove the ground tab. The metallic cartridge shield is disconnected from the right channel ground by the removal of the ground tab.

CAUTION. ronncctlon to cartridge

STYLUS REPLACEMENT (see ure stylus and gently pull forward out of stylus Into socket and press untll

housing

MOUNTING [12.7 mm (112 in.)

mounting centers]:

Mounting

2. Connect leads to cartridge (see

3. Lay cartridge in shell and align

4. Reinsert stylus (see Stylus Re- FIGURE

RECOMMENDED STYLUS CLEANING: Use or smaller), an stylus damage or corrosion. Always brush stylus from back to front; never brush or wipe stylus from front to back or side to side.

TO PRESERVE STYLUS LIFE:

3. If it is necessary to manually place the tone arm

4. Correct improper set-down adjustment or malfunction of the turntable

6. Use proper vertical tracking force setting for each cartridge.

8. When dusting the turntable protect the stylus with the stylus guard. SPECIAL NOTE:

cartrldge, be certain that any replacement stylus you buy bears the following certification on the package: "This Stereo

manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY

WILL SERIOUSLY DEGRADE THE PERFORMANCE OF YOUR CARTRIDGE.

ALL GENUINE "DYNETICB" STYLI ARE MANUFACTURED BY SHURE BROTHERS INC. LOOK FOR THE NAME SHURE ON THE STYLUS For more information on your Shure stylus, write for booklet: the Small World of

FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated 222 Hartrey Avenue, product that it will be free, in normal use, of any defects in workmanship and materials for a period of one year from date of purchase. You should retain proof of date of purchase. Shure is not liable for any consequential damages. fully repack the unit and return it prepaid to:

If you are not in the United States, return the unit to your dealer or Authorized Service Center for repair. The unit will be repaired or replaced and returned to you promptly, and if it cannot be repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear.

PATENT NOTICE: of the following

Brown

9.3

6.2 mV

Dark

Green

71%

oi ilgures above

720

millihenries

47,000 ohms resistance in parallel with 400 to 500 pico-

LOAD:

capacitance

"A+B." If amplliier is not equipped with this switch, connect left and

110

not make solder

Grasp molded houslng of

cartridge

Remove stylus guard and stylus (see Stylus Replacement).

Figure mountlng holes on ~ide of car-

tridge with holes or threads in shell. Follow turntable manufacturer's instructions to mount cartridge in tone arm or plug-in shell.

placement).

alcohol-distilled

Follow turntable or tone arm instructions when force. Do not handle the tone cause the arm to sweep across the record.

while turntable is record groove.

changing mechanism to prevent the stylus from striking the edge of the turntable or record. Do not stack more records than turntable manufacturer recommends. Take care to properly insert the stylus into the cartridge assembly and the cartridge and shell

Do not use badly warped, cracked or imperfect records.

Insert replacement

mates wlth

1).

If this Shure product has any defects as described above, care-

cartridge

screws are provided.

trlmmcd to approximately 6 mm (1/4 in.), dipped in alcohol or

water solution. Commercial cleaning solutions may cause

rotating,

To maintain the original performance standards of your

Stylus."

Evanston, Illinois 60204, warrants to the owner of this

Shure Brothers lncorporated Attention: Service Department

1501

Arlington Heights, Illinois 60004

Cartridge

U.S.

patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.

STYLI

SPECIFICATIONS

within

20 to

2 dB

20.000

20 to

20,000

Set

ampllfler to "MONO" or "A+ B

20 dB

kHz

2 to 4 grams

grams

400

1,000

10,000

at 3 grams

Hz Hz Hz

37 cm/sec

12 cm/sec

terminals

per channel. Load resistance can be up to 70,000

1):

Right "hot" lead (usually red) to "R," right

Left "hot" lead (usually white) to

terminals

Fig-

casr

kFNNNEL

TEWINAL-

ibZNEL

;;",","I;,,

17L+L

-1

FIGURE

camel's hair brush (No. 2 size

adjusting

arm

while it is in operat~on srrlce this may

release it as soon as the stylus engages the

asscmbly into the tone arm receptacle.

West Shure Drive

and stylus manufactured under one or more

in the record groove

Dynetic@ stylus is precision

/RIGHT

CHANNkL TERMINAL

-GROUND TAB

RIGHT

CHANNEL GROUND TERMINAL

GROUNDED

antiskating

Visit to

YShure"),

"L,"

CASE

GRIP.

cm/sec