Shure X100 User Manual

222

HARTREY

AVE..

EVANSTON.

TWX:

910.231.0048

THE

PREMIER FAMILY OF STEREO SOUND REPRODUCERS

IL.

TELEX:

60204

72-4381

STEREO DYNETIC@

'Io0

CARTRIDGE AND STYLUS SPECIFICATIONS

*&P

N75-6

151~

(.0006 in.)

Spher~cal

N75-3t

6% (.0025

Spherical

?Optional 78 rpm Stylus: Set amplifier to "MONO" or "A+B."

*Output voltages given for stereo cut record. For MONO cut record,

output voltage at both left channel and right channel cartridge terminals will be

**Tracking forces greater than maximum indicated should not be used.

NET WEIGHT: 6.2 grams

INDUCTANCE: 720 millihenries DC RESISTANCE: 630 ohms OPTIMUM LOAD: 47,000 ohms resistance in parallel with 400 to 500 pico-

farads total capacitance per channel. Load resistance can be up to 70,000 ohms with almost no audible change in frequency response. Total capacitance includes both tone arm wiring and amplifier input circuit.

FOUR-CHANNEL: This Stereo

four-channel matrix systems.

MONOPHONIC OPERATION: Set function switch on amplifier to "MONO" or

right channels in parallel. CONNECTIONS (see Figure

ground (usually green) to "RG." Left "hot" lead (usually white) to left ground (usually blue) to "LG." If metal head is causing ground loop hum, remove the ground tab. The metallic cartridge shield is disconnected from the right channel ground by the removal of the ground tab.

CAUTION: Do not make solder

connection to cartridge terminals.

STYLUS REPLACEMENT (see Fig-

ure 2): Grasp molded housing of

stylus and gently pull forward

out of cartridge. Insert replace-

ment stylus into socket and press

until housing mates with cartridge case. FIGURE

MOUNTING [12.7 mm (1/2 in.)

mounting centers]: Mounting screws are provided.

2. Connect leads to cartridge (see

4. Reinsert stylus (see Stylus Re-

RECOMMENDED STYLUS CLEANING: Use a camel's hair brhsh (No. 2 size or smaller), trimmed to approximately 6 mm an alcohol-distilled water solution. Commercial cleaning solutions may cause stylus damage or corrosion. Always brush stylus from back to front; never brush or wipe stylus from front to back or side to side.

TO PRESERVE STYLUS LIFE:

2. Do not handle the tone arm while

4. Correct improper set-down adjustment or malfunction of the turntable

5. Take care to properly insert the stylus into the cartridge assembly and

6. Use proper vertical tracking force setting for each cartridge.

8. When dusting the turntable protect the stylus with the stylus guard. SPECIAL NOTE:

cartridge, be certain that any replacement stylus you buy bears the following certification on the package: "This Stereo

manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY WILL SERIOUSLY DEGRADE THE PERFORMANCE OF YOUR CARTRIDGE. ALL GENUINE BROTHERS INC. LOOK FOR THE NAME SHURE ON THE STYLUS

For more information on your Shure stylus, write for pamphlet: "Don't be

penny-wise and sound foolish." FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated YShure"),

222 Hartrey Avenue, Evanston, Illinois 60204, warrants to the owner of this product that it will be free, in normal use, of any defects in workmanship and materials for a period of one year from date of purchase. You should

retain proof of date of purchase. Shure is not liable for any consequential

damages. If this Shure product has any defects as described above, care-

fully repack the unit and return

If you are not in the United States, return the unit to your dealer or Authorized Service Center for repair. The unit will be repaired or replaced and returned to you promptly, and if it cannot be repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear.

PATENT NOTICE: Cartridge and stylus manufactured under one or more

of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.

Beige

Dark

Green

in.)

71%

of figures above.

"A+B." If amplifier is not equipped with this switch, connect left and

Remove stylus guard and stylus (see Stylus Replacement).

1).

Figure

Lay cartridge in shell and align mounting holes on side of cartridge with holes or threads in shell. Follow turntable manu-

facturer's instructions to mount cartridge in tone arm or plug-in shell.

placement). FIGURE

Follow turntable or tone arm instructions when adjusting antiskating force.

cause the arm to sweep across the record. If it is necessary to manually place the tone arm in the record groove while turntable is rotating, release it as soon as the stylus engages the record groove.

changing mechanism to prevent the stylus from striking the edge of the turntable or record. Do not stack more turer recommends.

the cartridge and shell assembly into the tone arm receptacle. Do not use badly warped, cracked or imperfect records.

"DYNETIC@" STYLI ARE MANUFACTURED BY SHURE

6.2

20,000

6.2 mV

20,000

To maintain the

Shure Brothers lncorporated Attention: Service Department 15W West Shure Drive Arlington Heights, Illinois 60004

PHONOGRAPH CARTRIDGE

Dynetic@ cartridge is compatible with all

1): Right "hot" lead (usually red) to OR," right

within

2 dB

kHz

1v2

grams

to3

grams

400

1,000

10,W

at 2 grams

Hz Hz Hz

18 cm/sec

25 cm/sec

14 cm/sec

"L,"

kEzNEL

TERM'NAL-/

(1/4 in.), dipped in alcohol or

it is in operation since this may

records than turntable manufac-

ortginal performance standards of your

Dynetic@ stylus is precision

(AL633)

prepaid to:

CASE

GRIP.

U.S.A