Shure WA470 User Guide

Model W A470

Antenna Splitter/ Combi ner User Guide

When using multiple receivers, select antennas for each

WA470 as follows:

When used as an antenna splitter, the Shure Model
WA470 Antenna Splitter/Combiner allows two diversity
VHF receivers or up to four non-diversity VHF receivers
to receive signals from only two antennas. This minimizes
the number of antennas required and helps prevent inter­ference problems in installations with multiple receivers.

When used as an antenna combiner, the WA470 routes
signals from four antennas to the inputs of a single VHF
diversity receiver, while retaining true diversity perfor­mance. This is useful in applications where one wireless
system must provide coverage in two areas.

Optimum results can be achieved by using Shure
WA380 half-wave antennas and WA420 or other 50Ω
coaxial cables. The WA470 can be used with the quarter­wave antennas supplied with the wireless systems if the
antennas are mounted directly to the WA470.

NOTE: Each wireless system must operate on a d ifferent
frequency. Frequencies must be selected in accordance
with government regulations and system characteristics.
Contact your Shure dealer for more information.

Selecting the Proper Antenna

Shure recommends using WA380 half–wave antennas
with the WA470 splitter/combiner. Half–wave antennas
provide up to 3 dB more gain than quarter–wave anten­nas. Half–wave antennas must be used if antennas are
not mounted directly to the WA470. They are available in
three configurations, which correspond to three frequency
bands:

• WA380A - 169 to 185 MHz

• WA380B - 185 to 200 MHz

• WA380C - 200 to 230 MHz

Installing the WA470 as an Antenna Splitter

To install the WA470 as an antenna splitter, refer to Figure
1 and proceed as follows:

• If the frequencies are both in the same band, select
antennas for that band.

• If the frequencies span two adjacent bands, select
antennas for the lowest frequency band.

• If the frequencies span all three bands, use one
WA380A antenna and one WA380C antenna. This will
cover the entire frequency range with only a slight
decrease in system performance.

1.Slide the WA470 into a 19-in. audio equipment rack and
secure it using four screws and washers.

2.Mount two half–wave antennas around the installation
as desired:

• To wall mount the antennas, use the mounting brackets

supplied with the WA380 antennas.

• To rack mount the antennas, use a Shure WA440 Rack

Mount Kit .

• To mount the antennas on microphone stands, us e Shure

A57 swiv el adapters (or equiv alent) .

NOTE: As an alternative, two quarter–wave antennas
may be mounted directly on the front of the WA470.

3.Connect each antenna to the WA470 using coaxial
cables (WA420 or equivalent).

4.Fully extend the antennas for optimum reception.

5.Using the supplied RF cables, connect the antenna in­puts of the receivers to the RF outputs of the WA470.

1/2 WAVE

ANTENNAS

2002, Shure Incorporated
27B8399 (Rev. 4)

NON–DIVERSITY RECEIVERS

WA470

DIVERSITY RECEIVERS

WA470

WA470 INSTALLED AS ANTENNA SPLITTER

FIGURE 2

1/2 WAVE

ANTENNAS

Printed in U.S.A.

Installing the WA470 as an Antenna Combiner

The WA470 c an b e used t o c ombine s ignals f rom f our a nten­nas into the inputs of a single diversity receiver, while r etain­ing true diver sity perf ormance. This is par ticularly usef ul in
applications where two wireless systems must provide cov­erage in adjacent areas. To i nstall the W A470 a s an a ntenna
combiner, refer to Figure 2 and proceed as follows:

6.Slide the WA470 into a 19-inch audio equipment rack.

7.Secure the WA470 to the rack with four screws and
washers.

8.Mount four half–wave antennas, two in each area, as
desired:

• To wall mount the antennas, use the mounting brackets

supplied with the WA420 antennas.

• To rack moutn the antennas, use a Shure WA440 Rack

Mount Kit.

• To mount the antennas on microplhone stands, use

Shure A57 Swivel Adapters (or equivalent).

9.Connect each pair of antennas to WA470 connectors A
and B. Use Shure WA420 Antenna Cable or any 50Ω,
low loss antenna cable (RG–8x or equivalent).

10.Using the supplied interconnecting RF cables, connect
the WA470 output connectors to the antenna inputs on
the receiver, as shown in Figure 2.

SPECIFICATIONS

RF Carrier Frequency Range

169 to 230 MHz

Antenna Input Impedance

50Ω nominal

RF Output Impedance

50Ω nominal

Overall Dimensions

44.45 mm H x 482 mm L x 57.15 mm D
(1-3/4 in. x 19 in. x 2-1/4 in.)

Weight

779.63 g (1 lb, 11.5 oz.)

WA470 INSTALLED AS ANTENNA COMBINER

FIGURE 2

FURNISHED ACCESSORIES

0.6 m (2 ft.) coaxial Interconnecting RF Cable (4) 95B8217. . .

OPTIONAL ACCESSORIES

169 to 185 MHz Antenna WA380A. . . . . . . . . . . . . . . . . . . . .

185 to 200 MHz Antenna WA380B. . . . . . . . . . . . . . . . . . . . .

200 to 230 MHz Antenna WA380C. . . . . . . . . . . . . . . . . . . . .

6.1 m (20 ft.) Coaxial Cable Assembly WA420. . . . . . . . . . .

Antenna Rack Mount Kit WA440. . . . . . . . . . . . . . . . . . . . . .

SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
In U.S.A., Phone: [phone] Fax: [phone]
In Europe, Phone: [phone] Fax: [phone]
In Asia, Phone: [phone] Fax: [phone]
International Fax: [phone]