Shure Sound Isolating SE310 User Manual

SE310

Sound Isolating™ Earphones

Featuring sound isolating
design and Tuned BassPort
enhanced Hi-Definition

MicroSpeakers, the Shure

SE310 delivers extended

range audio and enhanced

bass. An ideal personal
listening device upgrade, the
stylish Shure SE310 includes
a carrying case, modular

cable, interchangeable

Sound Isolating™ sleeves

and adapters—providing

a comfortable,

personalized fit and

maximum portability

©2006, Shure Incorporated
27EN3244 (Rev. 2)

Printed in U

.S.A.

INSERTING THE EARPHONES

If the earphone seems to be lacking in low frequency response (bass), check
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.

To replace sleeve, carefully remove old one and slide new sleeve over nozzle barb. If any
part of the nozzle is exposed, sleeve is not properly installed. Replace sleeves if they do
not grip the nozzle tightly

WEARING THE EARPHONES

Three suggested methods for wearing the earphones are illustrated below.

Tighten the cable and take up slack by raising the cable sleeve.

Over the ear

in back

Over the ear

in front

Straight down

in front

Cable

Sleeve

Nozzle Barb

CHOOSING AN EARPHONE SLEEVE

Your earphones come with a selection of sleeves. Make sure the sleeve you
choose is easy to insert into your ear, fits comfortably, and is easy to remove
from your ear.

Soft Foam Sleeves

When using the foam sleeves, compress the sleeve between your
fingers before inserting it into the ear canal. Hold the earphone in
place for about ten seconds while the foam expands and creates
a tight seal.

Triple-Flange Sleeves

If desired, the sleeve stem may be shortened. Use sharp scissors
to carefully trim the stem to the desired length.

Soft Flex Sleeves

In small, medium, and large sizes.
Made from pliable rubber.

Note: carefully slide sleeve over earphone nozzle barb for a secure grip.

REMOVING THE EARPHONES

Grasp the body of the earphone and gently twist to remove.

CLEANING THE EARPHONE NOZZLE

If you notice a change in sound quality, remove the sleeve and check
the nozzle of your earphone. If nozzle is blocked, clear obstruction
by using wire loop end of cleaning tool.

Nozzle

Wire Loop

When cleaning, do not force any object through the earphone nozzle!

This will damage the earphone sound filter.

Note: Do not pull on cable to remove the earphone.

Warning: Do not push the earphone sleeve beyond the ear canal opening.

Sleeve

Sleeve Over Barb

Cleaning
Tool

FURNISHED ACCESSORIES

• Deluxe Carrying Case

• Fit Kit: contains soft foam, soft flex and triple flange sleeves plus
cleaning tool

• Stereo Extension Cable - 3 ft. (91cm)

TECHNICAL SPECIFICATIONS

Transducer type Balanced-armature drivers

Sensitivity (at 1kHz) 111 dB SPL/mW

Impedance (at 1kHz) 28 W

Frequency Range 22Hz- 19kHz

DC Resistance

23 W

Input connector 3.5 mm (1/8 in.) gold-plated stereo plug

Net weight 28g (1 oz)

Operational temperature -18° C to 57° C (0° F to 135° F)

Storage temperature -29° C to 74° C (-20° F to 165° F)

CUSTOM EARPHONE SLEEVES

Those who use earphones regularly for extended periods of time often find
custom-fit molded sleeves offer the best comfort and sound isolation.

Sensaphonics Hearing Conservation Toll Free: [phone]

660 N. Milwaukee Avenue In Chicago: [phone]

Chicago, IL 60622

e-mail: [e-mail]

www.sensaphonics.com

MAINTENANCE

Careful maintenance ensures a tight seal between the sleeve and nozzle,
improving sound quality and product safety.



Keep the earphones and sleeves as clean and dry as possible.



To clean sleeves, remove them from earphones, gently rinse in warm
water and air dry. Foam sleeves require a longer drying time. Inspect for
damage and replace if necessary.

Ear sleeves must be completely dry before reusing.



Wipe the earphones and sleeves with mild antiseptic to avoid infections.
Do not use alcohol-based disinfectants.



Do not expose earphones to extreme temperatures.



Replace sleeves if they do not fit properly.

CERTIFICATION

Eligible to bear CE marking.
Conforms to European EMC Directive 89/336/EEC.

Meets applicable tests and performance criteria in European
Standard EN

55103 (1996) Parts 1 and 2, for residential (E1) and

light industrial (E2) environments.

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: [phone] U.S. Fax: [phone] Int’l Fax: [phone]

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: [phone] Fax: [phone]

Asia, Pacific:

Shure Asia Limited, Phone: [phone] Fax: [phone]

ACCESSORIES

For information about earphone accessories (listed below) and other Shure
products visit: www.shure.com

• Replacement Sleeves • Extension Cables

• Carrying Cases • Push To Hear (PTH)

• Adapters • Volume Control

Ask a Hearing Health Care Professional about creating custom molded sleeves
for your earphones. For more information, contact: