Shure ShowLink AD610 Important Safety Instructions Manual
AD610 -- ShowLink® Access Point
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor
dance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara
tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam
aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas
es, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing
connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
1/13
21. Operate this product within its specified operating temperature range.
Explanation of Symbols
Caution: risk of electric shock
Caution: risk of danger (See note.)
Direct current
Alternating current
On (Supply)
Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION
Shure Incorporated
Stand-by
Equipment should not be disposed of in the normal waste stream
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing
to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from
the factory setting.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or
other reproductive harm.
AD610 ShowLink Access Point
The AD610 ShowLink access point enables real-time remote control of all ShowLink-enabled Axient™ transmit
ters, including both digital and analog models. The access point allows comprehensive management of transmitter
parameters from the receiver or Wireless Workbench 6 using 2.4 GHz wireless network communication. All para
meter changes occur without interruption to the performer.
®
Multiple access points can extend the operational range or increase the number of transmitters supported on the
ShowLink network. The access point also features true diversity antenna inputs.
Features
• Real-time wireless remote control of up to 24 transmitters per ShowLink access point
• New RF design and true diversity antenna scheme for improved link performance
• Easy transmitter authentication—Recognizes linked transmitters upon IR sync
• Provides coverage area approximately the same as the transmitter’s range
• Automatic hand-offs between multiple access points extend operating range
2/13
Shure Incorporated
• Automated channel selection—Independently scans 2.4 GHz frequency range and determines best channel for
use
• Automatic frequency agility—Moves a ShowLink network to the best available 2.4 GHz channel in the event of
signal degradation
• Wireless Workbench 6 software supports networked control of all device functions and provides a ShowLink
plot for viewing 2.4 GHz signal levels
• Receives power via Power over Ethernet (PoE) network connection or from an external power supply
• Versatile mounting options—Fits microphone stand adapters and has builtin ¼"20 and M6 x 1.0 threading for
installation
• Backwards compatible with Axient analog transmitters and receiver
ShowLink Access Point Overview
① ShowLink 2.4 GHz detachable antennas
For 2.4 GHz signals
② ShowLink Data Status LED (blue)
• ON Steady: Linked, no data transmission
• Flashing: Transmitting data. Rate of flashing indicates level of activity
3/13
③ Power Status LED (green/amber/red)
• Steady Green: Power ON, power source = PoE
• Steady Amber: Power ON, power source = external power supply
• Red Flashing: Response to remote ID flash command
④ Ethernet Status LED (green)
• ON Steady: Ethernet connected, no traffic
• ON Flashing: Ethernet connected, flashing corresponds to volume of data traffic
⑤ ¼"-20 threaded mounting point
Use to wall-mount the access point
⑥ External power supply connector
Connection point for external power supply
⑦ Reset button
Shure Incorporated
Press to restore factory settings
⑧ Ethernet port
For network connection and Class 1 PoE
⑨ Scanning antenna for channel agility
Scans the 2.4 GHz spectrum for the best frequency
⑩ M6 x 1.0 threaded mounting point
Use to mount access point to safety cable
Furnished Accessories
Wireless Microphone Clip WA371
5/8" to 3/8" Thread Adapter 31A1856
Shielded 25 foot Ethernet cable for ShowLink access point, RJ45-to-EtherCon
connector
95A15104
Power Supply PS43
Note: Model availability depends on region. See your local Shure dealer or distributor for details.
4/13
Loading...