Shure SE110 User Manual

©2007, Shure Incorporated
27EN3254 (Rev. 2)

Sound Isolating™ Earphones

SE110

Balanced MicroSpeakers and a

stylish sound isolating design to

deliver a rich, lifelike listening

experience, the Shure SE110 is
an ideal portable listening device
upgrade. An included modular cable

and interchangeable Sound

Isolating™ sleeves provide a

comfortable, personalized

t. The carrying case further

enhances the portability of

these lightweight earphones.

Printed in U.S.A.

Suggested methods for wearing the earphones are
illustrated below.

WEARING THE EARPHONES

Over the ear

in back

Over the ear

in front

Tighten the cable and take up slack by raising the cable sleeve.

Straight down

in front

Cable

Sleeve

If the earphone seems to be lacking in low frequency response (bass),
check the tightness of the seal between the earphone and your ear, or
try one of the other sleeve options.

INSERTING THE EARPHONES

Warning: Do not push the earphone sleeve beyond the ear canal opening.

To change earphone sleeve, twist and pull sleeve to remove it from the nozzle.

Push new sleeve onto nozzle until you feel it slide completely over barb. If any
part of the nozzle is exposed, sleeve is not properly installed. Replace sleeves if

they do not grip the nozzle tightly

Grasp the body of earphone and gently twist to remove.

Nozzle Barb

REMOVING THE EARPHONES

Note: Do not pull on cable to remove earphone.

Your earphones come with a selection of sleeves. Make sure the sleeve

you choose is easy to insert into your ear, ts comfortably, and is easy

to remove from your ear.

Soft Flex Sleeves

In small, medium, and large sizes.
Made from pliable rubber.

Soft Foam Sleeves

CHOOSING AN EARPHONE SLEEVE

When using the foam sleeves, compress the sleeve

between your ngers before inserting it into the ear canal.

Hold the earphone in place for about ten seconds while the
foam expands and creates a tight seal.

Note: carefully slide sleeve over earphone nozzle barb for a secure grip.

If you notice a change in sound quality, remove the sleeve and check
the nozzle of your earphone. If nozzle is blocked, clear obstruction by
using wire loop end of cleaning tool.

Cleaning

Tool

Wire Loop

Nozzle

Barb

CLEANING THE EARPHONE NOZZLE

Nozzle

When cleaning, do not force any object through the earphone
nozzle! This will damage the earphone sound lter.

Warning: The wax removal loop is only to be used to clean

earphones. Any other use, such as using the tool to clean
ears, could result in injury.

• Soft Carrying Case

• Fit Kit: contains soft foam and soft ex sleeves plus a cleaning tool

• Stereo Extension Cable - 3 ft. (91 cm)

ACCESSORIES

For information about earphone accessories (listed below) and other

FURNISHED ACCESSORIES

Shure products visit: www.shure.com

Transducer type Balanced armature drivers

Sensitivity (at 1kHz) 113 dB SPL/mW

Impedance (at 1kHz) 27 W

DC Resistance 18.5 W

Frequency Range 22Hz - 17.5kHz

TECHNICAL SPECIFICATIONS

Input connector 3.5 mm (1/8 in.) gold-plated stereo plug

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

Phone: [phone] U.S. Fax: [phone] Int’l Fax: [phone]

Shure Europe GmbH, Phone: [phone] Fax: [phone]

Shure Asia Limited, Phone: [phone] Fax: [phone]

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Europe, Middle East, Africa:

Asia, Pacic:

• Replacement Sleeves • Extension Cables

• Carrying Cases • Push To Hear (PTH)

• Music Phone Adapter • Volume Control

User Guide
Earphone

SE110

Careful maintenance ensures a tight seal between the sleeve and
nozzle, improving sound quality and product safety.



MAINTENANCE









x

CERTIFICATION

Keep the earphones and sleeves as clean and dry as possible.

To clean sleeves, remove them from earphones, gently rinse in
warm water and air dry. Foam sleeves require a longer drying

time. Inspect for damage and replace if necessary.

Ear sleeves must be completely dry before reusing.

Wipe the earphones and sleeves with mild antiseptic to avoid
infections. Do not use alcohol-based disinfectants.

Do not expose earphones to extreme temperatures.

Replace the sleeves if they do not t properly.

Do not attempt to modify this product. Doing so will void the
warranty and could result in personal injury and/or product failure.

Eligible to bear CE marking.

Conforms to European EMC Directive 89/336/EEC.

Meets applicable tests and performance criteria in

European Standard EN 55103 (1996) Parts 1 and 2, for

residential (E1) and light industrial (E2) environments.

Net weight 30g (1.05 oz)

Operational temperature -18° C to 57° C (0° F to 135° F)

Storage temperature -29° C to 74° C (-20° F to 165° F)

Those who use earphones regularly for extended periods of time often
nd custom-t molded sleeves offer the best comfort and sound isolation.

Ask a Hearing Health Care Professional about creating custom molded

sleeves for your earphones. For more information, contact:

CUSTOM EARPHONE SLEEVES

Sensaphonics Hearing Conservation Toll Free: [phone]

660 N. Milwaukee Avenue In Chicago: [phone]

Chicago, IL 60622

e-mail: [e-mail]

www.sensaphonics.com