Shure SCL5 User Manual

/

©2007, Shure Incorporated
27EN3251 (Rev. 1)

Sound Isolating Earphones

SCL5

The SCL5 combines Dual Live

Performance Drivers with an Inline

Crossover to create the same reference-

quality audio developed for

professional musicians.

The result of dedicated

speakers for highs

and lows is the faithful

reproduction of precision

highs, natural mids, and

full-bodied bass.

Printed in U.S.A.

WEARING THE EARPHONES

Two popular methods for wearing the earphones are illustrated below.

Over the ear
in back

Tighten the cable and take up slack by raising the cable sleeve .

Over the ear
in front

INSERTING THE EARPHONES

If the earphone seems to be lacking in low frequency response (bass), check
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.

Warning: Do not push the earphone sleeve beyond the ear canal opening.

left ear

Make sure that the sleeve completely
covers the earphone nozzle. If any part

of the nozzle is exposed, the sleeve is
not properly installed.

right ear

CHOOSING AN EARPHONE SLEEVE

Your earphones come with a selection of sleeves. Make sure the sleeve you

use is easy to insert into your ear, ts comfortably, and is easy to remove from

your ear.

Soft Flex Sleeves

In small, medium, and large sizes. Made from pliable rubber.

Yellow and Black Foam Sleeves

When using the foam sleeves, compress the sleeve between

your ngers before inserting it into the ear canal. Hold the

earphone in place for about ten seconds while the foam
expands and creates a tight seal. Black foams come in
small, medium and large sizes.

Triple-Flange Sleeves

If desired, the sleeve nozzle may be shortened. Use sharp
scissors to carefully trim the nozzle to the desired length.

CLEANING THE EARPHONE NOZZLE

If the nozzle of your earphone is blocked, clean the nozzle using the supplied
wax removal loop.

Wax Removal Loop

Nozzle

When cleaning, do not force any object through the earphone nozzle! This will

damage the earphone sound lter.

If necessary, the supplied replacement nozzles may be used. See the back of
this guide for instructions on nozzle replacement.

Warning: The wax removal loop is only to be used to clean
earphones. Any other use, such as using the tool to clean
ears, could result in injury.

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

Phone: [phone] U.S. Fax: [phone] Int’l Fax: [phone]

Shure Europe GmbH, Phone: [phone] Fax: [phone]

Shure Asia Limited, Phone: [phone] Fax: [phone]

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Europe, Middle East, Africa:

Asia, Pacic:

MAINTENANCE

Careful maintenance ensures a tight seal between the sleeve and nozzle,
improving sound quality and product safety.

Keep the earphones and sleeves as clean and dry as possible.



To clean sleeves, remove them from earphones, gently rinse in
warm water and air dry. Foam sleeves require a longer drying
time. Inspect for damage and replace if necessary.



Ear sleeves must be completely dry before reusing.

Wipe the earphones and sleeves with mild antiseptic to avoid



infections. Do not use alcohol-based disinfectants.

Do not expose earphones to extreme temperatures.



Replace the sleeves if they do not t properly.



Do not attempt to modify this product. Doing so will void the

x

warranty and could result in personal injury and/or product failure.

FURNISHED ACCESSORIES

• Premium Carrying Case

• Fit Kit: contains soft foam, soft ex and triple ange sleeves plus

cleaning tool

• Stereo Adapter Plug - 1/4 in. (6.5mm) to 1/8 in. (3.5mm)

ACCESSORIES

For information about earphone accessories (listed below) and other Shure
products visit: www.shure.com

• Replacement Sleeves • Extension Cable

• Carrying Case • Push To Hear (PTH Module)

• Adapters • Volume Control

TECHNICAL SPECIFICATIONS

Transducer type Dual low mass/high energy

Sensitivity (at 1kHz) 122 dB SPL/mW

Impedance (at 1kHz) 110 W

Output connector Gold-plated 3.5 mm (1/8-inch) stereo plug

Cable length 155 cm (61”)

Net weight 31 g (1.1 oz.)

Operational temperature -18° C to 57° C (0° F to 135° F)

Storage temperature -29° C to 74° C (-20° F to 165° F)

CUSTOM EARPHONE SLEEVES

Those who use earphones regularly for extended periods of time often nd
custom-t molded sleeves offer the best comfort and sound isolation.

Ask a Hearing Health Care Professional about creating custom molded sleeves
for your earphones. For more information, contact:

Sensaphonics Hearing Conservation Toll Free: [phone]

660 N. Milwaukee Avenue In Chicago: [phone]

Chicago, IL 60622

e-mail: [e-mail]

www.sensaphonics.com

CERTIFICATION

Eligible to bear CE marking.

Conforms to European EMC Directive 89/336/EEC.

Meets applicable tests and performance criteria in European Standard
EN 55103 (1996) Parts 1 and 2, for residential (E1) and light industrial (E2)
environments.