Shure SBC250 User Manual

SBC250
2-Up Networked Docking Station

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor

dance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara
tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam
aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas
es, on the apparatus.

16. The MAINS plug or an appliance coupler shall remain readily operable.

17. The airborne noise of the Apparatus does not exceed 70dB (A).

18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing
connection.

1/12

19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

21. Operate this product within its specified operating temperature range.

Explanation of Symbols

Caution: risk of electric shock

Caution: risk of danger (See note.)

Direct current

Alternating current

On (Supply)

Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION

Shure Incorporated

Stand-by

Equipment should not be disposed of in the normal waste stream

WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing
to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from
the factory setting.

General Description

SBC250 networked docking station provides simple charging, configuration, and storage for either 2 ULXD6 and
ULXD8 transmitters. Dock transmitters for 15 minutes to get 1 hour of use, or charge for 3 hours for a full charge.

Connect to a network to adjust transmitter settings and monitor rechargeable battery information. Use Shure con

trol software such as Wireless Workbench or other external control systems such as AMX or Crestron to monitor
and make changes.

®

Features

• Compatible with ULXD6 and ULXD8 transmitters using Shure rechargeable batteries

• Connect up to 2 transmitters for 15 minutes to get 1 hour of use, or 3 hours for a full charge

• Easily adjust transmitter settings using Shure control software such as Wireless Workbench and external con

trol systems such as AMX or Crestron

• Monitor rechargeable battery information such as health, temperature, charge, and cycle using control software

• Update transmitter and docking station firmware using Shure Update Utility

2/12

Shure Incorporated

• Rack- or wall-mountable with Shure URT3 mounting tray (sold separately)

Rack and Wall Mounting

SBC250 can be rack- or wall-mounted using the optional Shure URT3 universal rack tray for added flexibility when
storing ULXD6 boundary microphones.

① When mounting to a rack, position the rotatable ears on the URT3 with the

holes facing forward

② For mounting to a wall, rotate the ears so the holes are flush with the surface

Caution: When mounted on the wall, insert and remove ULXD6 boundary microphones vertically to avoid damag

ing the USB connector

More Information Available Online

A comprehensive online user guide is available at pubs.shure.com (http://pubs.shure.com).

3/12

Controls and Connectors

Shure Incorporated

① Power Switch

Powers the unit on or off.

② AC Power

IEC connector 100 - 240 V AC.

③ Power LED

• On = Docking station is on

• Off = Docking station is off

④ Ethernet Port

Connect to an Ethernet network to enable remote device control and monitoring using Wireless Workbench or oth

er control software.

⑤ Ethernet Link Speed LED (Amber)

• Off = 10 Mbps

• On = 100 Mbps

⑥ Ethernet Status LED (Green)

• Off = No network link

• On = Network link established

• Flashing = Network link active

⑦ Charging Slots (USB 3.0)

Slide any ULXD6 or ULXD8 transmitter with Shure rechargeable batteries into slots to begin charging.

4/12