THE SHURE UHF MK2 SERIES WIRELESS SYSTEMS MEET THE ESSENTIAL REQUIREMENTS OF THE EUROPEAN R&TTE DIRECTIVE 99/5/E AND ARE ELIGIBLE
TO BEAR THE CE MARKING.
SHURE UHF COMPONENTS BEARING THE MK2 INSIGNIA ARE COMPATIBLE
WITH OTHER SHURE UHF SERIES WIRELESS SYSTEMS, BUT ARE NOT
INTERCHANGEABLE WITH UHF SERIES COMPONENTS; I.E., A UHF MK2
TRANSMITTER CANNOT BE USED WITH A U4 RECEIVER THAT LACKS THE MK2
INSIGNIA.
U1, U2: 152.4 m, minimum, under typical conditions; 487.6 m line of sight
NOTE: Actual working range depends on RF signal absorption, reflection and
interference
Audio Frequency Response
50 to 15,000 Hz, ±2 dB.
NOTE: Overall system frequency response depends on the microphone element
Gain Adjustment Range
U1: 0 to 40 dB
U2: 0 to 26 dB
Modulation
±18 kHz deviation compressor-expander system with pre-and de-emphasis
RF Power Output
U1, U2: 10 mW maximum
Dynamic Range
>102 dB, A-weighted
RF Sensitivity
U4SU4D
-110 dBm
12 dB SINAD
-105 dBm
30 dB SINAD
Image Rejection
90 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (ref. 18 kHz deviation)
>100 dB, A-weighted
Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of
WA302 phone plug) produces positive voltage on pin 2 with respect to pin 3 of low
impedance output and the tip of the high impedance 1/4-inch output
System Distortion(ref. ±18 kHz deviation, 1 kHz modulation)
U4S: 9.6 W min., 13.2 W max.
U4D: 12 W min.,16 W max.
UA840: 15 W min., 16 W max.
Battery Life (Typical)
U1, U2: 12 hours (with 1.5V AA alkaline battery)
Operating Temperature Range
-6° to +49° C
NOTE: Battery characteristics may limit this range
-107 dBm
12 dB SINAD
-102 dBm
30 dB SINAD
2
U1 Transmitter Input(Figure 1)
Connector:TA4F or
Input Configuration:Unbalanced, active
Actual Impedance:18 kΩ with lavalier microphone
Maximum Input Level:6 Vp-p (+7 dBV) for 1% THD at minimum gain setting
TA4F Connector Pin
Assignments:
LEMO Connector
Pin Assignments:
Pin 4: Tied to Shield (Ground for Positive Bias)
Voltage for Remote Power:+5 V supplied to microphone cartridge
LEMO connector (optional)
1 MΩ with instrument cable
using 1 kHz signal.
Pin 1: Tied to Ground
Pin 2: Tied to +5 V
Pin 3: Tied to Audio
Pin 4: Tied thru 20 kΩ Resistor to Ground.
(On instrument adapter cable, Pin 4 floats)
Pin 1: Tied to Pin 3 and 10 kΩ to Ground
Pin 2: +5V
Pin 3: Tied to Pin 1
MICROPHONE
ELEMENT
NOTE: LAVALIER MIC TIES PINS 3 AND 4
TOGETHER; GUITAR CABLE DOES NOT.
1
2
3
4
2
4
3
1
U1L (LEMO 4 PIN) MIC JACK BOARD
499 &!
10K &!
2
4
3
1
499 &!
27 pF
U1 MIC JACK BOARD
500 &!
27 pF
FIGURE 1
U1Transmitter Output
Connector:SKK
Actual Impedance:50 Ω
Nominal Output Level:+10 dBm
Maximum Output Level:+11 dBm
Pin Assignments:Shell = Ground
Center = Signal
27 pF
AUDIO
BIAS
SHIELD
500 &!
20K &!
27 pF
+5 V
AUDIO
GROUND
3
U2 Transmitter Input
Input Configuration:Unbalanced, active
Actual Impedance:20 k Ω
Maximum Input Level:3 Vp-p (0.5 dBV) for 1% THD at minimum gain setting using
1 kHz signal.
U2 Transmitter Output
Connector:SKK
Actual Impedance:50 Ω
Nominal Output Level:+10 dBm
Maximum Output Level:+11 dBm
Pin Assignments:Shell = Ground
Center = Signal
U4S and U4D Receiver Input
Connector:AntennaPower InputNetwork Interface
Connector Type:BNCIEC 32025-Pin D
Actual Impedance:50 Ω ----
Nominal Input Level:-95 to -30 dBm230 VAC,
Maximum Input
Level:
Pin Assignments:Shell = Ground
Voltage for
Remote Power:
+6 dBm
(-20 dBm
recommended)
Center = Signal
12 Vdc, 150 mA
maximum
50/60 Hz
254 VAC, 50/60 Hz--
IEC Standard--
--5V, 700 mA max.
CMOS Logic
U4S and U4D Receiver Output
Connector:MonitorPower
Output
Configuration:
Actual
Impedance:
Nominal
Input Level:
Pin
Assignments:
Voltage/
Current/
Phantom
Power
Protection?
*Output Level: Microphone Level = Line Level - 30 dB
Unbalanced
mono, 1/4 inch
300 Ω--1 k Ω30 ΩSee
--230 VAC, 5A----CMOS
Tip = Hot
Ring = Hot
Sleeve = Gnd
Yes--YesYes5V, 700
Output
--UnbalancedBalancedSee
IEC
Standard
4
High Z
Audio
Tip = Hot
Ring/ Sleeve
= Gnd
Low Z
Audio*
1 = Ground
2 = Hot
3 = Hot
Network
Interface
Appendix
Appendix
Logic
See
Appendix
mA
resettable
polyfuse
Overall Dimensions
U1: 92.2 mm L x 64.7 mm W x 24.2 mm D
U2/58: 228.6 mm L x 51 mm Dia.
U2/SM86: 213 mm L x 49 mm Dia.
U2/BETA 58: 220.9 mm L x 51 mm Dia.
U2/87: 223.5 mm x 51 mm Dia.
U2/BETA 87: 228 mm L x 50 mm Dia
U4S/U4D: 44.5 mm H x 482.6 mm W x 295.3 mm D
Net Weight
U1: 175.2 g without battery
U2/58, U2/BETA 58: 330 g without battery
U2/86: 332 g without battery
U2/87, U2/BETA 87: 339 g without battery
U4S: 3.30 kg
U4D: 3.85 kg
Certification
The Shure UHF series wireless systems meet the essential requirements of the European R&TTE Directive 99/5/EC and are eligible to carry the CE marking.
U1, U2: Conforms to European ETSI Standard EN 300 422 (Parts 1 and 2) and ETS
300445/A1.
U4, U4D: Conforms to European ETSI Standard EN 300 445/A1 and EN 60950.
THIS RADIO EQUIPMENT IS INTENDED FOR USE IN PROFESSIONAL ENTERTAINMENT (CLASS I) AND SIMILAR APPLICATIONS.
Changes or modifications not expressly approved by Shure Incorporated could void your
authority to operate the equipment. Licensing of Shure wireless microphone equipment is
the user's responsibility, and licensability depends on the user's classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing
and ordering frequencies.
R&TTE CONFORMITY INFORMATION
IMPORTANT! Shure Models U1 and U2 Transmitters meet the essential requirements of
the European R&TTE Directive 99/5/EC and are eligible to carry the CE
marking.
Shure Model U4 Receivers meet the essential requirements of the European R&TTE Directive 99/5/EC and are eligible to carry the CE marking.
THIS RADIO EQUIPMENT IS INTENDED FOR USE IN MUSICAL PROFESSIONAL EN-
TERTAINMENT AND SIMILAR APPLICATIONS.
NOTE: THIS RADIO APPARATUS MAY BE CAPABLE OF OPERATING ON SOME
FREQUENCIES NOT AUTHORIZED IN YOUR REGION. PLEASE CONTACT YOUR
NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES FOR WIRELESS MICROPHONE PRODUCTS IN YOUR REGION
Frequency Range of Apparatus: 692 MHz - 862 MHz
6
Licensing: A ministerial license to operate this equipment may be required in certain
areas. Consult your national authority for possible requirements.
Shure Transmitters Models U1 and U2 may be used in the countries and frequency
ranges listed in Table 1.
NOTE: Shure recommends that you maintain a 500 kHz separation between each receiver
channel in the U4D dual channel receivers. Please contact the Shure Customer Service
Department (1-800-434-3350) if you need additional information or assistance in frequency
selection and setup.
TABLE 1
Country
Code
A692-716
B692-716
CH692-716
D692-716
E692-716
F692-716
GB692-716
GR692-716
I692-716
IRL692-716
L692-716
NL692-716
P692-716
DK**800-810
FIN**800,1-810
N**800-810
S**800-810
All Other
Countries
U1-M3,
U2-M3
(692 - 716
MHz)
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
******
U1-R3,
U2-R3
(774 - 782
MHz)
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
U1-R7,
U2-R7
(782 - 810
MHz)
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R6,
U2-R6
(800 - 820
MHz)
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
**838-862
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800,1-819,9
MHz*
800-820
MHz*
800-814
MHz*
U1-R2,
U2-R2
(800 - 830
MHz)
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800,1-819,9
MHz*
800-830
MHz*
800-814
MHz*
U1-S2, U2-S2
(838 - 862
MHz)
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
MHz*
838-862
MHz*
*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
*
*
*
*Please contact your national authority for information on available legal frequencies for your
area and legal use of the equipment.
7
UHF WIRELESS SYSTEM COMPATIBILITY GUIDE
Table 2 provides a convenient overview of frequency-compatible systems in the
838.000 to 862.000 MHz band. Each of the primary groups contains multiple channels
which are all compatible with one another.
Up to 16 Shure UHF Wireless Systems can be operated simultaneously within the 838862 MHz band if using the discontinued UHF KK versions, or a combination of KK and
MK2 S2 versions. Up to 28 UHF MK2 systems can be operated simultaneously within
the 838-862 MHz band.
Note: Combinations of Shure UHF transmitters and UHF MK2 receivers, and combinations of UHF MK2 transmitters and UHF receivers are NOT supposed to work together.
Always use a transmitter-receiver combination of the same frequency version (S2 or
KK).
Groups 1-10 MUST be chosen if the installation includes a pure setup of Shure UHF
Wireless Systems (frequency version KK only) or a mixed setup of Shure UHF and
Shure UHF MK2 Wireless Systems (frequency versions KK and S2)
Groups 1-10 CAN be chosen if the installation includes a pure setup of Shure UHF
MK2 Wireless Systems (frequency version S2 only).
Groups 11-28 CAN ONLY be chosen if the installation includes a pure setup of Shure
UHF MK2 Wireless Systems (frequency version S2 only).
Note: Contact your national frequency authority to get information on the available legal
frequencies for your area and legal use of the equipment.
FREQUENCY GROUP CONTENTS
GROUPS 1-10*
Group 1 contains 10 compatible frequencies which are derived from a combination of
fixed site (Multiple UHF High and Low) frequencies, as well as Indoor Use at Fixed Site
frequencies.
Group 2 contains 14 fixed site frequencies taken entirely from the Multi UHF High and
Low Band (these frequencies are not compatible!).
Groups 3-4 provide 10 compatible frequencies within TV channel 69 (854-862 MHz).
Groups 5-7 provide 16 compatible frequencies within TV channels 68-69 (846-862
MHz).
Groups 8-10 contain 16 compatible frequencies within TV channels 67-69 (838-862
MHz).
GROUPS 11-28 *
Groups 11-13 provides the maximum number of compatible frequencies between 838
and 862 MHz.
Group 14 complies with the new German RegTP regulations for public users (“Nutzergruppe 4“) within TV channels 67-69.
Group 15 complies with the new German RegTP regulations for users of “Nutzergruppe
3A“ within TV channels 67-69.
Group 16 complies with the new German RegTP regulations for users of “Nutzergruppe
3B“ within TV channels 67-69.
Group 17 complies with the new German RegTP regulations for users of “Nutzergruppe
3C“ within TV channels 67-69.
8
Group 18 complies with the new German RegTP regulations for users of “Nutzergruppe
3D“ within TV channels 67-69.
Group 19 complies with the new German RegTP regulations for broadcast users of
“Nutzergruppe 2“ within TV channels 67-69.
Group 20 complies with the new German RegTP regulations for broadcast users of
“Nutzergruppe 1“ within TV channels 67-69.
Group 21 provides the maximum number of compatible frequencies between 838-846
MHz (TV channel 67)
Group 22 provides the maximum number of compatible frequencies between 846-854
MHz (TV channel 68)
Group 23 provides the maximum number of compatible frequencies between 854-862
MHz (TV channel 69)
Group 24 contains compatible “Co-ordinated Frequencies” of the recommended “SET
1" as listed by the JFMG**.
Group 25 contains compatible “Co-ordinated Frequencies” of the recommended “SET
2" as listed by the JFMG**.
Group 26 contains “Co-ordinated Frequencies” for INDOOR use.
Groups 27-28 contain “Co-ordinated Frequencies” for OUTDOOR use.
* Contact your national frequency authority to get information on the available legal
frequencies for your area and legal use of the equipment. Contact the Shure Customer
Service Department if you need additional information on frequency selection and system
setup.
** JMFG Limited is a company that has been contracted by the UK Radiocommunications
Agency since April 1997 to manage and license that part of the radio spectrum used for
Program Making and Special Events in the UK.
9
TABLE 2
SYSTEM COMPATIBILITY GUIDE
S2 FREQUENCY BAND (838 - 862 MHz)
Channel Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 Group 9Group
152,4 mètres dans les conditions typiques; 487.6 m max.
REMARQUE : La distance utile réelle dépend des facteurs affectant le signal RF, tels
que l'absorption, la réflexion et les perturbations.
Réponse en fréquence audio
50 à 15 000 Hz, ±2 dB.
REMARQUE : La réponse en fréquence globale dépend de la qualité du microphone.
Gamme de réglage du gain
U1 : 0 à 40 dB
U2 : 0 à 26 dB
Modulation
Système compresseur-extenseur d'écart ±18 kHz avec préaccentuation et désaccentuation.
Puissance de sortie RF
U1, U2 : 10 mW maximum.
Dynamique
>102 dB, pondéré A
Sensibilité RF
U4SU4D
-110 dBm
12 dB SINAD
-105 dBm
30 dB SINAD
Rejet d'image
90 dB (typique)
Rejet des fréquences parasites
75 dB (typique)
Atténuation ultime (réf. écart de 18 kHz)
>100 dB, pondéré A
Polarité audio
Une pression positive sur le diaphragme du microphone (ou une tension positive appliquée au bout de la fiche téléphonique WA302) engendre une tension positive à la
broche 2 par rapport à la broche 3 de la sortie à basse impédance et à l'extrémité du
jack 1/4 po de la sortie à haute impédance.
Distorsion du système (réf. écart ±18 kHz, modulation 1 kHz)
0,3 % de distorsion harmonique totale (typique).
Alimentation électrique
U1, U2 : piles alcalines AA de 1,5 V; piles au nickel-cadmium en option.
U4 : 230 Vca, 50/60 Hz.
Consommation de puissance: 9.6 W min, 13.2 W max (U4S)
12 W min, 16 W max (U4D)
15 W min, 16 W max (UA840)
Capacité des piles (typique)
12 heures d'utilisation (piles alcalines AA de 1,5 V).
Température de fonctionnement
-6 à +49 °C. REMARQUE : Les caractéristiques des piles peuvent changer ces valeurs.
-107 dBm
12 dB SINAD
-102 dBm
30 dB SINAD
12
Entrée de l'émetteur U1 (Figure 1)
Connecteur :TA4F ou LEMO (en option)
Configuration de l'entrée :Asymétrique, active
Impédance réelle :18 kΩ avec micro-cravate
Niveau d'entrée maximal :6 V c-à-c (+7 dBV) pour 1 % DHT; gain minimal et
Affectation des broches
TA4F :
Broche 4 = 20 kΩ à Masse et Audio (Sur le cordon
adaptateur d'instrument, la broche 4 est flottante)
Affectation des broches LEMO :Broche 1 : à Broche 3 et 10 kΩ à Masse
Tension d'alimentation
fantôme :
1 MΩ avec cordon d'instrument
signal de 1 kHz
Broche 1 : à Masse
Broche 2 : à +5 V
Broche 3 : à Audio
Broche 2 : à +5 V
Broche 3 : à Broche 1
Broche 4 : à Blindage (Masse por biase positif)
+5V alimenté à la cartouche du microphone
500 &!
27 pF
TABLEAU DE U1
POLARISATION
MICROPHONE
2
4
3
1
NOTA: LE M IC RO -C RAVATE RE LE I LES MO RN ES 3 ET 4 , MAIS
LE CORDON DE GUITARE NE LE FAIT P AS.
CIRCUIT DE JACK MICRO U1L (LEMO 4 BROCHES)
1
2
3
4
499 &!
499 &!
10K &!
2
4
3
1
27 pF
FIGURE 1
Sortie de l'émetteur U1
Connecteur :Antenne
Impédance réelle :50 Ω
Niveau de sortie nominal :+10 dBm
Niveau de sortie maximal :+11 dBm
Affectation des broches :Boîtier = Masse
Centre = Signal
500 &!
27 pF
AUDIO
BLINDAGE
20K &!
27 pF
+5 V
AUDIO
MASSE
13
Entrée de l'émetteur U2
Configuration de l'entrée :Asymétrique, active
Impédance réelle :20 kΩ
Niveau d'entrée maximal :3 V c-à-c (+0.5 dBV) pour 1 % DHT; gain minimal et
signal de 1 kHz
Sortie de l'émetteur U2
Connecteur :SKK
Impédance réelle :50 Ω
Niveau de sortie nominal :+10 dBm
Niveau de sortie maximal :+11 dBm
Affectation des broches :Boîtier = Masse
Centre = Signal
Entrée des récepteurs U4S et U4D
Connecteur :AntenneEntrée secteurInterface réseau
Type de connecteur :BNCCEID 25 broches
Impédance réelle :50 Ω----
Niveau d'entrée nominal :-95 à -30 dBm90 à 230 Vca, 50/60
Niveau d'entrée maximal :
Affectation des broches :Boîtier = Masse
Tension d'alimentatio
fantôme :
+6 dBm
(-20 dBm
recommand
Centre = Signal
12 V cc, 150 mA
maximal
é)
Hz
230 V ca, 50/60 Hz--
Norme CEI--
----
LogiqueCMOS
Sortie des récepteurs U4S et U4D
Connecteur :Écouteurs de
Configuration
de la sortie :
Impédance
réelle :
Niveau
d'entrée
nominal :
Affectation
des broches :
Protection
tension/
intensité/
alimentation
fantôme
*Niveau de sortie: mic = ligne - 30 dB
contrôle
Mono
asymétrique, 1/4
po
300 Ω--1 kΩ30 ΩVoir
--90 à 230
Pointe = Sous
tension
Nuque = Sous
tension
Gaine = Masse
OuiOuiOui5V, 700 mA
Sortie
secteur
--AsymétriqueSymétriqueVoir
Vca, 5 A
Norme
CEI
Audio à
haute
impédance
----Logique CMOS
Pointe = Sous
tension
Nuque/gaine
= Masse
Audio à bass
impédance*
1 = Masse
2 = Sous
tension
3 = Sous
tension
Interface
réseau
annexe
annexe
Voir
annexe
max.
14
Encombrement
U1 : 92,2 x 64,7 x 24,2 mm (L x Lr x P)
U2/58 : 228,6 x 51 mm (L x diam.)
U2/86 : 213 x 49 mm (L x diam.)
U2/BETA 58A : 220,9 x 51 mm (L x diam.)
U2/87 : 223,5 x 51 mm (L x diam.)
U2/BETA 87 : 228 x 50 mm (L x diam.)
U4S/U4D : 44,5 x 482,6 x 295,3 mm (H x Lr x P)
Poids net
U1 : 175,2 g sans piles
U2/58, U2/BETA 58A : 330 g sans piles
U2/86: 332 g sans piles
U2/87, U2/BETA 87 : 339 g sans piles
U4S : 3,30 kg
U4D : 3,85 kg
Homologation
Les systèmes sans fil série UHF Shure sont conformes aux exigences essentielles
de la directive européenne R&TTE 99/5/CE et sont autorisés à porter la marque CE.
U1, U2 : Conforme à la norme ETSI européenne EN 300 422 (parties 1 et 2) et ETS
300 445/A1.
U4, U4D : Conforme à la norme ETSI européenne ETS 300 445/A1 et EN 60950.
CE MATéRIEL RADIO EST PRéVU POUR UTILISATION EN SPECTACLES PROFESSIONNELS (CLASSE I) ET APPLICATIONS SIMILAIRES.
Tout changement ou modification n'ayant pas fait l'objet d'une autorisation expresse de
Shure Incorporated peut entraîner la nullité du droit d'utilisation de l'équipement. La licence d'utilisation de l'équipement du microphone sans fil Shure demeure la responsabilité de l'utilisateur, et elle dépend de la classification de l'utilisateur et de l'application
prévue par lui ainsi que de la fréquence sélectionnée. Shure recommande vivement de
se mettre en rapport avec les autorités compétentes des télécommunications pour l'obtention des autorisations nécessaires, ainsi qu'avant de choisir et de commander des
fréquences.
INFORMATIONS DE CONFORMITÉ R&TTE
IMPORTANT ! Les transmetteurs modèles Shure U1 et U2 conforme aux exigences es-
sentielles de la directive européenne R&TTE 99/5/CE et sont autorisés à porter la
marque CE.
Le recepteur modèle Shure U4 conforme aux exigences essentielles de la directive européenne R&TTE 99/5/CE et sont autorisés à porter la marque CE.
CE MATéRIEL RADIO EST PRéVU POUR UTILISATION EN SPECTACLES PROFESSIONNELS ET APPLICATIONS SIMILAIRES.
REMARQUE : IL EST POSSIBLE QUE CE MATéRIEL SOIT CAPABLE DE FONCTIONNER SUR CERTAINES FRéQUENCES NON AUTORISéES LOCALEMENT. SE
METTRE EN RAPPORT AVEC LES AUTORITéS COMPéTENTES POUR OBTENIR
LES INFORMATIONS SUR LES FRéQUENCES AUTORISéES POUR LES
SYSTèMES DE MICROPHONES SANS FIL LOCALEMENT
Gamme de fréquences pour ce matériel : 692 MHz-862 MHz
16
Autorisation d'utilisation : Noter qu'une licence officielle d'utilisation de ce matériel peut
être requise dans certains endroits. Consulter les autorités compétentes pour les spécifications possibles.Les modèles d'transmetteur Shure U1 et U2 peuvent être utilisés dans
les pays et aux gammes de fréquences indiqués au Tableau 1.
REMARQUE : Shure recommande de maintenir une séparation de 500 kHz entre chaque canal de
récepteur dans les récepteurs à canal double U4D. Ne pas hésiter à contacter le service clientèle de
Shure (49-7131-72140) pour toute assistance ou informations complémentaires concernant la
sélection et le réglage des fréquences.
TABLEAU 1
Code de
Pays
A692-716
B692-716
CH692-716
D692-716
E692-716
F692-716
GB692-716
GR692-716
I692-716
IRL692-716
L692-716
NL692-716
P692-716
DK**800-810
FIN**800,1-810
N**800-810
S**800-810
Tous les
autres pays
U1-M3,
U2-M3
(692 - 716
MHz)
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
******
U1-R3,
U2-R3
(774 - 782
MHz)
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
U1-R7,
U2-R7
(782 - 810
MHz)
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R6,
U2-R6
(800 - 820
MHz)
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
**838-862
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800,1-819,9
MHz*
800-820
MHz*
800-814
MHz*
U1-R2,
U2-R2
(800 - 830
MHz)
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800,1-819,9
MHz*
800-830
MHz*
800-814
MHz*
U1-S2, U2-S2
(838 - 862
MHz)
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
MHz*
838-862
MHz*
*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
*
*
*
*Se mettre en rapport avec les autorités compétentes pour obtenir les informations sur les
fréquences autorisées disponibles localement et sur l'utilisation autorisée du matériel.
17
GUIDE DE COMPATIBILITÉ DU SYSTÈME SANS FIL S2 UHF
Le Tableau 2 donne une liste générale des systèmes compatibles en fréquence dans
la bande de 838,000 à 862,000 MHz. Chaque groupe comprend plusieurs canaux compatibles les uns avec les autres.
Jusqu'à 16 systèmes sans fil UHF Shure peuvent être utilisés simultanément dans la
bande de 838 à 862 MHz si ces systèmes sont de versions de fréquence KK (abandonnées) ou d'une combinaison de versions KK et S2.
Jusqu'à 28 systèmes sans fil MK2 UHF Shure peuvent être utilisés simultanément dans
la bande de 838 à 862 MHz s'ils sont tous de versions de fréquence S2.
Remarque : Les combinaisons d'émetteurs UHF Shure et de récepteurs MK2 UHF
Shure ainsi que les combinaisons d'émetteurs MK2 UHF Shure et de récepteurs UHF
Shure NE SONT PAS censées fonctionner. Toujours utiliser les combinaisons
émetteurs-récepteurs de même version de fréquence (S2 ou KK).
Les groupes 1 à 10 DOIVENT être utilisés si l'installation comprend des systèmes
sans fil UHF Shure (fréquence KK seulement) ou des systèmes sans fil UHF Shure et
des systèmes sans fil MK2 UHF Shure (fréquences KK et S2)
Les groupes 1 à 10 PEUVENT être utilisés si l'installation comprend des systèmes
sans fil MK2 UHF Shure seulement (versions de fréquence S2).
Les groupes 11 à 28 peuvent UNIQUEMENT être utilisés si l'installation comprend
des systèmes sans fil MK2 UHF Shure seulement (versions de fréquence S2).
Remarque : Il est possible que cet appareil soit capable de fonctionner sur certaines
fréquences non autorisées localement. Se mettre en rapport avec les autorités compétentes pour obtenir les informations sur les fréquences autorisées pour les microphones sans fil localement.
COMPOSANTS DES GROUPES
Groupes 1 à 10 (Utilisée especialment dans le Royaume-Uni)
Le groupe 1 comprend 10 fréquences compatibles prises qui se sont dérives a partir
d'une combinaison de fréquences fixes multiple UHF haute et basse, ainsi que les
fréquences fixes intérieures utilisées.
Le groupe 2 comprend 14 fréquences pour site fixe prises entièrement de la bande multiple haute et basse UHF (ces fréquences NE SONT PAS compatibles !)
Les groupes 3 à 4 offrent 10 fréquences compatibles dans le canal de télévision 69 (854
à 862 MHz).
Les groupes 5 à 7 offrent 16 fréquences compatibles dans les canaux de télévision 68
et 69 (846 à 862 MHz).
Les groupes 8 à 10 offrent 16 fréquences compatibles dans les canaux de télévision 67
à 69 (832 à 862 MHz).
Groupes 11 à 28
Les groupes 11 à 13 offrent le nombre maximum de fréquences compatibles entre 838
et 862 MHz.
Le groupe 14 est conforme aux réglementations allemandes RegTP pour utilisateurs
publics (« Nutzergruppe 4 ») dans les canaux de télévision 67 à 69.
Le groupe 15 est conforme aux nouvelles réglementations allemandes RegTP pour utilisateurs du groupe « Nutzergruppe 3A » dans les canaux de télévision 67 à 69.
Le groupe 16 est conforme aux nouvelles réglementations allemandes RegTP pour utilisateurs du groupe « Nutzergruppe 3B » dans les canaux de télévision 67 à 69.
18
Le groupe 17 est conforme aux nouvelles réglementations allemandes RegTP pour utilisateurs du groupe « Nutzergruppe 3C » dans les canaux de télévision 67 à 69.
Le groupe 18 est conforme aux nouvelles réglementations allemandes RegTP pour utilisateurs du groupe « Nutzergruppe 3D » dans les canaux de télévision 67 à 69.
Le groupe 19 est conforme aux nouvelles réglementations allemandes RegTP pour utilisateurs de diffusion du groupe « Nutzergruppe 2 » dans les canaux de télévision 67 à
69.
Le groupe 20 est conforme aux nouvelles réglementations allemandes RegTP pour util-
isateurs de diffusion du groupe « Nutzergruppe 1 » dans les canaux de télévision 67 à
69.
Le groupe 21 offre le nombre maximum de fréquences compatibles entre 838 et 846
MHz (canal de télévision 67).
Le groupe 22 offre le nombre maximum de fréquences compatibles entre 846 et 854
MHz (canal de télévision 67).
Le groupe 23 offre le nombre maximum de fréquences compatibles entre 854 et 862
MHz (canal de télévision 67).
Le groupe 24 comprend les « fréquences coordonnées » du « GROUPE 1 » recom-
mandé comme indiqué par le JFMG**.
Le groupe 25 comprend les « fréquences coordonnées » du « GROUPE 2 » recom-
mandé comme indiqué par le JFMG**.
Le groupe 26 comprend les « fréquences coordonnées » pour utilisation À L'IN-
TÉRIEUR de bâtiments.
Les groupes 27 à 28 comprennent les « fréquences coordonnées » pour utilisation À
L'EXTÉRIEUR de bâtiments.
*Se mettre en rapport avec les autorités compétentes pour obtenir les informations sur les
fréquences autorisées disponibles localement et sur l'utilisation autorisée du matériel.
** JMFG Limited est une entreprise qui, sous contrat de l'UK Radiocommunications Agency
depuis avril 1997, gère et octroie les licences de la partie du spectre de fréquences radio
utilisée pour les émissions de radio et les reportages au Royaume-Uni.
19
TABLEAU 2
SYSTÈMES COMPATIBLES EN FRÉQUENCE DANS LA BANDE S2 (838 - 862 MHZ)
150 m Minimum unter Normalbedingungen; 500 m maximal.
HINWEIS: Die tatsächliche Reichweite hängt von der HF-Signalabsorption, -reflexion und -interferenz ab.
Audiofrequenzgang
50 bis 15,000 Hz, ±2 dB.
HINWEIS: Der Gesamtaudiofrequenzgang des Systems hängt vom Mikrophonelement ab.
Verstärkungsbereich
U1: 0 bis 40 dB
U2: 0 bis 26 dB
Modulation
±18 kHz Komprimierungs-/Dekomprimierungssystem mit Preemphasis und Deemphasis.
Dynamikbereich
>102 dB, mit A-Bewertung
HF-Empfindlichkeit:
U4SU4D
-110 dBm
12 dB SINAD
-105 dBm
30 dB SINAD
HF-Leistungsabgabe
U1, U2: maximal 10 mW
Spiegelselektion
90 dB (typisch)
Oberwellenunterdrückung
75 dB (typisch)
Grenzschalldämmung (bzgl. 18 kHz Abweichung)
>100 dB, mit A-Bewertung
Audiopolarität
Positiver Druck auf die Mikrophonmembran (oder positive Spannung an der Spitze
des Klinkensteckers WA302) erzeugt positive Spannung an Pin 2 hinsichtlich Pin 3
des Niederimpedanzausgangs und der Spitze des Hochimpedanz-6,3mm-Ausgangs.
U1, U2: 1,5-V-Alkalibatterie, wahlweise NiCd
U4: 230 V Wechselstrom, 50/60 Hz
Leistungsaufnahme: 9.6 W min, 13.2 W max (U4S)
12 W min, 16 W max (U4D)
15 W min, 16 W max (UA840)
Batterielebensdauer Sender (typisch)
12 Stunden (für 1,5-V-Alkalibatterien)
Betriebstemperaturbereich
-6° bis +49° C
HINWEIS: Batterieeigenschaften können diesen Bereich einschränken.
-107 dBm
12 dB SINAD
-102 dBm
30 dB SINAD
22
U1-Sendereingang (Abbildung 1)
Anschluß:TA4F oder LEMO-Anschluß (optional)
Eingangskonfiguration:Asymmetrisch, aktiv
Tatsächliche Impedanz:18 kΩ Bei Lavalier-Mikrophon
Maximaler Eingangs-
6 Vss (+7 dBV) für 1% Gesamtklirrfaktor bei minimaler
pegel:
TA4F
Pinkonfiguration:
Instrumentenadapterkabeln ist Pin 4 nicht geerdet)
LEMO Pinkonfiguration:Pin 1: an Pin 3 und 10 kΩ an Erdung
Spannung für
Phantomspeisung:
1MΩ mit Instrumentenkabel
Verstärkungseinstellung mit 1 kHz Signal
Pin 1: Erdung
Pin 2: +5V
Pin 4 : an 20 kΩ für Erdung & Audio (bei
Pin 3: Audio
Pin 2: +5V
Pin 3: Pin 1
Pin 4: an der Schirmung (Erdung)
+5 V Versorgung an Mikrophonkapsel
MIKROPHON
ELEMENT
HINWEIS: DAS LAVALIERKABEL VERBINDET Pin 3 UND 4; DAS
GITARRENKABEL ERFÜLLT DIESE FUNKTION NICHT
U1, H x B x T: 92,2 mm x 64,7 mm x 24,2 mm
U2/58, L x Durchmesser: 228,6 mm x 51 mm
U2/SM86, L x Durchmesser: 213 mm x 49 mm
U2/BETA 58A, L x Durchmesser: 220,9 mm x 51 mm
U2/87, L x Durchmesser: 235,5 mm x 51mm
U2/BETA 87, L x Durchmesser: 228 mm x 50 mm
U4S/U4D: H x B x T: 44,5 mm x 482,6 mm x 295,3 mm
Nettogewicht
U1: 175,2 g ohne Batterien
U2/58, U2/BETA 58A: 330 g ohne Batterien
U2/86: 332 g ohne Batterien
U2/87, U2/BETA 87: 339 g ohne Batterien
U4S: 3,3 kg
U4D: 3,85 kg
Zulassung
Die Drahtlossysteme der Serie Shure UHF entsprechen den Grundanforderungen
der europäischen R&TTE-Richtlinie 99/5/EC und sind zum Tragen des CE-Zeichens
berechtigt.
U1, U2: Entspricht der europäischen ETSI Norm EN 300 422, Teil 1 und 2, und ETS
300 445/A1.
U4, U4D: Entspricht der europäischen ETSI Norm EN 300 445/A1 und EN 60950.
DIESES FUNKGERäT IST ZUR VERWENDUNG IM UNTERHALTUNGSGEWERBE (KLASSE I) UND IN ÄHNLICHEN ANWENDUNGEN VORGESEHEN.
Nicht ausdrücklich von Shure Incorporated genehmigte Änderungen oder Modifikationen können den Entzug der Betriebsgenehmigung für das Gerät zur Folge haben. Das
Erlangen einer Lizenz für drahtlose Shure-Mikrofonsysteme obliegt dem Benutzer. Die
Erteilung einer Lizenz hängt von der Klassifizierung und Anwendung durch den Benutzer sowie von der ausgewählten Frequenz ab. Shure empfiehlt dem Benutzer dringend, sich vor der Auswahl und Bestellung von Frequenzen mit der zuständigen
Fernmelde-/Regulierungsbehörde hinsichtlich der ordnungsgemäßen Zulassung in
Verbindung zu setzen.
R&TTE-ÜBEREINSTIMMUNGSINFORMATIONEN
WICHTIG! Die Senders Modells U1 und U2 entsprechen den Grundanforderungen der
europäischen R&TTE-Richtlinie 99/5/EC und sind zum Tragen des CE-Zeichens berechtigt.
Der Empfänger Modell U4 entsprechen den Grundanforderungen der europäischen
R&TTE-Richtlinie 99/5/EC und sind zum Tragen des CE-Zeichens berechtigt.
DIESES FUNKGERäT IST ZUR VERWENDUNG IM UNTERHALTUNGSGEWERBE
UND IN ÄHNLICHEN ANWENDUNGEN VORGESEHEN.
HINWEIS: DIESES GERäT KANN MöGLICHERWEISE AUF EINIGEN FREQUENZEN ARBEITEN, DIE IN IHREM GEBIET NICHT ZUGELASSEN SIND. WENDEN SIE
SICH BITTE AN DIE ZUSTäNDIGE BEHöRDE, UM INFORMATIONEN üBER ZUGELASSENE FREQUENZEN FüR DRAHTLOSE MIKROFONPRODUKTE IN IHREM
GEBIET ZU ERHALTEN.
Frequenzbereich den dieses Gerät: 692 MHz-862 MHz
Zulassung: Es ist zu beachten, dass in einigen Gebieten für den Betrieb dieses Geräts
u.U. eine behördliche Zulassung erforderlich ist. Wenden Sie sich bitte an die zuständige Behörde, um Informationen über mögliche Anforderungen zu erhalten.
26
Die Shure-Sendermodelles U1 und U2 können in den Ländern und mit den Frequenzbereichen verwendet werden, die in Tabelle 1 aufgeführt sind.
HINWEIS: Shure empfiehlt, 500 kHz Kanaltrennung zwischen jedem Empfängerkanal in den 2Kanal-Empfängern U4D aufrecht zu erhalten. Wenn weitere Informationen oder Unterstützung
bei der Frequenzauswahl und Einrichtung gewünscht werden, wenden Sie sich bitte an die
Kundendienstabteilung von Shure (49-7131-72140)
TABELLE 1
Lander-KurzelU1-M3,
A692-716
B692-716
CH692-716
D692-716
E692-716
F692-716
GB692-716
GR692-716
I692-716
IRL692-716
L692-716
NL692-716
P692-716
DK**800-810
FIN**800,1-810
N**800-810
S**800-810
Alle anderen
Länder
U2-M3
(692 - 716
MHz)
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
******
U1-R3,
U2-R3
(774 - 782
MHz)
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
U1-R7,
U2-R7
(782 - 810
MHz)
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R6,
U2-R6
(800 - 820
MHz)
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
**838-862
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800,1-819,9
MHz*
800-820
MHz*
800-814
MHz*
U1-R2,
U2-R2
(800 - 830
MHz)
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800,1-819,9
MHz*
800-830
MHz*
800-814
MHz*
U1-S2,
U2-S2
(838 - 862
MHz)
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
MHz*
838-862
MHz*
*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
*
*
*
*Für Informationen bezüglich der für Ihr Gebiet verfügbaren gesetzlich zugelassenen Frequenzen
und der gesetzlichen Bestimmungen für den Einsatz der Geräte setzen Sie sich bitte mit der
zuständigen örtlichen Behörde in Verbindung.
27
KOMPATIBILITÄTSLEITFADEN FÜR UHF-S2-DRAHTLOSSYSTEME
Tabelle 2 stellt eine praktische Übersicht über frequenzkompatible Systeme im Frequenzbereich von 838.000 bis 862.000 MHz dar. Jede Gruppe enthält mehrere Kanäle,
die alle miteinander kompatibel sind.
Bis zu 16 Shure UHF-Drahtlossysteme können gleichzeitig innerhalb des 838-862
MHz-Frequenzbereichs betrieben werden, wenn es sich bei den Systemen um KK-Frequenzversionen (Produktion eingestellt) oder eine Kombination von KK- und S2-Ausführungen handelt.
Bis zu 28 Shure UHF-MK2-Drahtlossysteme können gleichzeitig innerhalb des 838-862
MHz-Frequenzbereichs betrieben werden, wenn alle Systeme S2-Frequenzausführungen sind.
Hinweis: Kombinationen von Shure UHF-Sendern und Shure UHF-MK2-Empfängern
und Kombinationen von Shure UHF-MK2-Sendern und Shure UHF-Empfängern sind
NICHT für den gemeinsamen Einsatz vorgesehen. Es müssen stets Sender/
Empfänger-Kombinationen derselben Frequenzausführung (S2 oder KK) verwendet
werden.
Gruppen 1-10 MÜSSEN verwendet werden, wenn folgende Systeme in der Installation vorhanden sind Shure UHF-Drahtlossysteme (nur KK-Frequenzausführungen)
oder Shure UHF-Drahtlossysteme und Shure UHF-MK2-Drahtlossysteme (KK- und S2Frequenzausführungen).
Gruppen 1-10 KÖNNEN verwendet werden, wenn folgende Systeme in der Installation vorhanden sind nur Shure UHF-MK2-Drahtlossysteme (S2-Frequenzausführungen).
Gruppen 11-28 können NUR verwendet werden, wenn folgende Systeme in der Installation vorhanden sind nur Shure UHF-MK2-Drahtlossysteme (S2-Frequenzausführungen)
Hinweis: Dieses Gerät kann möglicherweise auf einigen Frequenzen arbeiten, die an
Ihren Standorten nicht zugelassen sind. Wenden Sie sich bitte an die zuständige Behörde, um Informationen über zugelassene Frequenzen für drahtlose Mikrofone an
Ihren Standorten zu erhalten.
GRUPPENZUSAMMENSETZUNG
Gruppen 1-10*
Gruppe 1 enthält 10 kompatible Frequenzen, die sich aus einer Kombination aus Feststandort- (mehrere UHF-Hoch- und Niedrig-) Frequenzen sowie Feststandortfrequenzen zur Nutzung in geschlossenen Räumen ableiten.
Gruppe 2 enthält 14 Feststandortfrequenzen, die gänzlich dem Multi-UHF-Hoch- und
Niedrigfrequenzbereich entnommen sind (diese Frequenzen sind NICHT kompatibel!).
Gruppen 3-4 bieten 10 kompatible Frequenzen innerhalb des Fernsehkanals 69 (854862 MHz).
Gruppen 5-7 bieten 16 kompatible Frequenzen innerhalb der Fernsehkanäle 68-69
(846-862 MHz).
Gruppen 8-10 bieten 16 kompatible Frequenzen innerhalb der Fernsehkanäle 67-69
(838-862 MHz).
28
Gruppen 11-28*
Gruppen 11-13 bieten die maximale Anzahl kompatibler Frequenzen zwischen 838 und
862 MHz.
Gruppe 14 entspricht den deutschen RegTP-Verordnungen (der Regulierungsbehörde
für Telekommunikation und Post) für öffentliche Nutzer („Nutzergruppe 4“) innerhalb
der Fernsehkanäle 67-69.
Gruppe 15 entspricht den neuen deutschen RegTP-Verordnungen für Nutzer der
„Nutzergruppe 3A“ innerhalb der Fernsehkanäle 67-69
Gruppe 16 entspricht den neuen deutschen RegTP-Verordnungen für Nutzer der
„Nutzergruppe 3B“ innerhalb der Fernsehkanäle 67-69
Gruppe 17 entspricht den neuen deutschen RegTP-Verordnungen für Nutzer der
„Nutzergruppe 3C“ innerhalb der Fernsehkanäle 67-69
Gruppe 18 entspricht den neuen deutschen RegTP-Verordnungen für Nutzer der
„Nutzergruppe 3D“ innerhalb der Fernsehkanäle 67-69
Gruppe 19 entspricht den neuen deutschen RegTP-Verordnungen für Nutzer der
„Nutzergruppe 3A“ im neuen zulässigen Frequenzbereich bis zu 814 MHz.
Gruppe 20 entspricht den neuen deutschen RegTP-Verordnungen für Rundfunknutzer
der „Nutzergruppe 1“ innerhalb der Fernsehkanäle 67-69
Gruppe 20 entspricht den neuen deutschen RegTP-Verordnungen für Rundfunknutzer
der „Nutzergruppe 2“ im neuen zulässigen Frequenzbereich bis zu 814 MHz.
Gruppe 21 bieten die maximale Anzahl kompatibler Frequenzen zwischen 838 und 862
MHz (Fernsehkanäle 67).
Gruppe 22 bieten die maximale Anzahl kompatibler Frequenzen zwischen 846 und 854
MHz (Fernsehkanäle 68).
Gruppe 23 bieten die maximale Anzahl kompatibler Frequenzen zwischen 854 und 862
MHz (Fernsehkanäle 69).
Gruppe 24 enthält kompatible „koordinierte Frequenzen“ des empfohlenen „SET 1“
gemäß JFMG-Auflistung**.
Gruppe 25 enthält kompatible „koordinierte Frequenzen“ des empfohlenen „SET 2“
gemäß JFMG-Auflistung**.
Gruppe 26 enthält „koordinierte Frequenzen“ für die Nutzung in GESCHLOSSENEN
RÄUMEN.
Gruppen 27-28 enthalten „koordinierte Frequenzen“ für die Nutzung im FREIEN.
*Informationen über die an Ihren Standorten verfügbaren zulässigen Frequenzen und die
gesetzlichen Bestimmungen für den Einsatz der Geräte sind von der zuständigen örtlichen
Frequenzbehörde einzuholen.
** JMFG Limited ist ein Unternehmen, das im Auftrag der britischen Fernmeldebehörde seit
April 1997 den für Programmerstellung und Sonderveranstaltungen verwendeten Teil des
Radiofrequenzspektrums in Großbritannien und Nordirland verwaltet und Lizenzen erteilt.
.
.
.
.
.
29
TABELLE 2
FREQUENZKOMPATIBLE SYSTEME IM FREQUENZBEREICH S2 (838 - 862 MHz)
152,4 m mínimo, bajo condiciones típicas; 487.6 m (1600 pies) máximo.
NOTA: El alcance real depende de los niveles de absorción, reflexión e interferencia
de RF.
Respuesta de audiofrecuencia
50 a 15.000 Hz, ±2 dB.
NOTA: La respuesta de frecuencia del sistema total depende del elemento de micrófono utilizado
Gama de ajuste de ganancia
U1: 0 a 40 dB
U2: 0 a 26 dB
Modulación
Desviación de frecuencia de ±18 kHz con sistema de compresor/expansor y filtros
de preénfasis y deénfasis
Potencia de salida RF
U1, U2: 10 mW máx.
Gama dinámica
>102 dB (ponderación A)
Sensibilidad de RF
U4SU4D
-110 dBm
12 dB SINAD
-105 dBm
30 dB SINAD
Rechazo de imágenes
90 dB típico
Rechazo de señales espurias
75 dB típico
Silenciamiento máximo (ref. desviación de 18 kHz)
>100 dB (ponderación A)
Polaridad de señal de audio
Una presión positiva en el diafragma del micrófono (o un voltaje positivo aplicado a
la punta de la clavija tipo audífono WA302) produce un voltaje positivo en la clavija
2 con respecto a la clavija 3 de la salida de baja impedancia y con respecto a la punta
de la salida de alta impedancia con jack de 1/4 pulg.
Distorsión de sistema (ref. desviación de ±18 kHz, modulación de 1 kHz)
Distorsión armónica total: 0,3% típica
Requisitos de alimentación
U1, U2: Baterías tamaño AA de 1,5 V; baterías de NiCad opcionales.
U4: 230 VCA, 50/60 Hz
Consunción de alimentación: 9.6 W min, 13.2 W max (U4S)
12 W min, 16 W max (U4D)
15 W min, 16 W max (UA840)
Duración de la batería (típica)
12 horas (con baterías alcalinas AA de 1,5 V)
Gama de temperatura de funcionamiento
-6° a +49°C
NOTA: Las características de la batería podrían limitar esta gama.
-107 dBm
12 dB SINAD
-102 dBm
30 dB SINAD
32
Entrada de transmisor U1 (Figura 1)
Conector:TA4F o LEMO (opcional)
Configuración de
entrada:
Impedancia real:18 kΩ con micrófono de corbata
Nivel máximo de entrada:6 Vp-p (+7 dBV) para 1% de THD usando señal de 1 kHz
con ganancia en valor de ajuste mínimo
Conexión de clavijas de
conector TA4F:
Clavija 4: 20 kΩ respecto a tierra y audio
(en el cable adaptador para instrumento, la clavija 4 flota)
Conexión de clavijas de
conector LEMO:
Voltaje para potencia
Suministro de +5 V al cartucho del micrófono
fantasma:
Desequilibrada, activa
1 MΩ con cable para instrumento
Clavija 1: Tierra
Clavija 2: +5 V
Clavija 3: Audio
Clavija 1: a Clavija 3 y 10 kΩ a tierra
Clavija 2: +5 V
Clavija 3: Audio
Clavija 4: a escudo (tierra)
ELEMENTO DEL
MICROFONO
NOTA: LA CONEXION DE MICROFONO PARA CORBATA CONECTA
LACLAVIJA2ALA3;PERO EL CABLE DE GUITARRA NO LO HACE
TARJETA DE JACK DE MICROFONO U1L (CONECTOR LEMO DE 4 CLAVIJAS)
1
2
3
4
2
4
3
1
499 &!
10K &!
TARJETA DE JACKS PARA
MICROFONOS U1
2
4
500 &!
3
1
499 &!
27 pF
27 pF
FIGURA 1
Salida de transmisor U1
Conector: SKK
Impedancia real:50 Ω
Nivel nominal de salida:+10 dBm
Nivel máximo de salida:+11 dBm
Conexión de clavijas:Casco = Tierra
Centro = Señal
500 &!
20K &!
27 pF
AUDIO
POLARIZACION
BLINDAJE
27 pF
+5 V
AUDIO
TIERRA
33
Entrada de transmisor U2
Configuración de entrada:Desequilibrada, activa
Impedancia real:20 kΩ
Nivel máximo de entrada:3 Vp-p (+0.5 dBV) para 1% de THD usando señal de 1 kHz con
ganancia en valor de ajuste mínimo
Salida de transmisor U2
Conector:SKK
Impedancia real:50 Ω
Nivel nominal de salida:+10 dBm
Nivel máximo de salida:+11 dBm
Conexión de clavijas:Casco = Tierra
Centro = Señal
Entrada de receptores U4S y U4D
Conector:AntenaEntrada de potenciaConexión a red
Tipo de conector:BNCIEC 320Tipo D, 25 clavijas
Impedancia real:50 Ω ----
Nivel nominal de
entrada:
Nivel máximo de
entrada:
Conexión de
clavijas:
Voltaje para
potencia remota:
-95 a -30 dBm230 VCA, 50/60 HzLógica CMOS
+6 dBm
(-20 dBm
recomendado)
Casco = Tierra
Centro = Señal
12 VCC, 150 mA máx.----
254 VCA, 50/60 Hz--
Estándar IEC--
Salida de receptores U4S y U4D
Conector:MonitorPotencia de
Configuración
de salida
Impedancia
real:
Nivel nominal
de entrada:
Conexión de
clavijas:
¿Protección de
voltaje/
corriente/
potencia
fantasma?
*Nivel de salida: nivel de micrófono = nivel de línea - 30 dB
Monofónica,
desequilib.,
1/4 pulg
300 Ω --1 kΩ 30 Ω Vea
-- 230 VCA, 5
Punta = Señal
Anillo = Señal
Manguito =
Tierra
Sí--SíSí5 V, 700
salida
--DesequilibradaEquilibradaVea
A
Estándar
IEC
Audio alta
impedancia
----Lógica
Punta = Señal
Anillo/manguito
= Tierra
Audio baja
impedancia*
1 = Tierra
2 = Señal
3 = Señal
Conexión
a red
Apéndice
Apéndice
CMOS
Vea
Apéndice
mA máx.
34
Dimensiones totales
U1: 92,2 mm (largo) x 64,7 mm (an.) x 24,2 mm (alt.)
U2/58: 228,6 mm (largo) x 51 mm (diám.)
U2/SM86: 213 mm (largo) x 49 mm (diám.)
U2/BETA 58A: 220,9 mm (largo) x 51 mm (diám.)
U2/87: 223,5 mm x 51 mm (diám.)
U2/BETA 87: 228 mm (largo) x 50 mm (diám.)
U4S/U4D: 44,5 mm (alt.) x 482,6 (an.) x 295,3 mm (prof.)
Peso neto
U1: 175,2 g sin batería
U2/58, U2/BETA58A: 330 g sin batería
U2/SM86: 332 g sin batería
U2/87, U2/BETA 87: 339 g sin batería
U4S: 3,30 kg
U4D: 3,85 kg
Certificaciones
Los sistemas inalámbricos de la serie UHF de Shure cumplen con los requisitos esenciales de la directriz europea 99/5/EC de RTTE y califican para llevar la marca CE.
U1, U2: Conformen a la norma ETSI europea EN 300 422 (partes 1 y 2) y ETS 300
445/A1.
U4, U4D: Conformen a la norma ETSI europea ETS 300 422 y EN 60950.
ESTE EQUIPO DE RADIO HA SIDO DISEñADO PARA USARSE EN APLICACIONES DE ENTRETENIMIENTO PROFESIONAL (CLASE I) Y SIMILARES.
Las modificaciones o los cambios efectuados sin la aprobación expresa de Shure Incorporated podrían anular la autorización concedida para usar el equipo. La obtención
de licencias de operación para equipos de micrófonos inalámbricos Shure es responsabilidad del usuario, y la otorgabilidad de licencias dependerá de la clasificación y la
aplicación del usuario y de la frecuencia seleccionada. Shure recomienda enfáticamente al usuario ponerse en contacto con las autoridades de telecomunicaciones correspondientes respecto a la obtención de licencias antes de seleccionar y solicitar
frecuencias.
INFORMACION DE CONFORMIDAD RTTE
IMPORTANTE: Los transmisores modelos U1 y U2 de Shure cumplen con los requisi-
tos esenciales de la directriz europea 99/5/EC de RTTE y califican para llevar la marca
CE.
El receptor modelo U4 de Shure cumple con los requisitos esenciales de la directriz
europea 99/5/EC de RTTE y califican para llevar la marca CE.
ESTE EQUIPO DE RADIO HA SIDO DISEñADO PARA USARSE EN APLICACIONES
DE ENTRETENIMIENTO PROFESIONAL Y SIMILARES.
NOTA: ES POSIBLE QUE ESTE EQUIPO FUNCIONE EN ALGUNAS FRECUENCIAS NO AUTORIZADAS EN SU REGION. POR FAVOR CONTACTE A LA AUTORIDAD NACIONAL PARA OBTENER INFORMACION ACERCA DE LAS FRECUENCIAS AUTORIZADAS PARA PRODUCTOS CON MICROFONOS INALAMBRICOS
EN SU ZONA
Gama de frecuencias de este equipo: 692 MHz-862 MHz
36
Licencia de uso: Tenga presente que se puede requerir una licencia ministerial para
hacer funcionar este equipo en algunas áreas. Consulte a la autoridad nacional sobre los
posibles requisitos.
Los transmisores Shure modelos U1 y U2 pueden usarse en los países y gamas de frecuencias indicados en la Tabla 1.
NOTA: Shure recomienda mantener una separación de 500 kHz entre los canales de cada receptor
en los receptores U4D de dos canales. Comuníquese con el Departamento de Servicio de Shure
(49-7131-72140) si necesita información adicional o ayuda para la selección de frecuencias y
configuración del sistema.
TABLA 1
Codigo de
País
A692-716
B692-716
CH692-716
D692-716
E692-716
F692-716
GB692-716
GR692-716
I692-716
IRL692-716
L692-716
NL692-716
P692-716
DK**800-810
FIN**800,1-810
N**800-810
S**800-810
Demás países******
U1-M3,
U2-M3
(692 - 716
MHz)
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R3,
U2-R3
(774 - 782
MHz)
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
U1-R7,
U2-R7
(782 - 810
MHz)
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R6,
U2-R6
(800 - 820
MHz)
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
**838-862
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800,1-819,9
MHz*
800-820
MHz*
800-814
MHz*
U1-R2,
U2-R2
(800 - 830
MHz)
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800,1-819,9
MHz*
800-830
MHz*
800-814
MHz*
U1-S2, U2-S2
(838 - 862
MHz)
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
MHz*
838-862
MHz*
*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
*
*
*
* Comuníquese con la autoridad nacional para obtener información en cuanto a las frecuencias legales disponibles y usos legales del equipo en su área.
37
GUIA DE COMPATIBILIDAD DE SISTEMA INALAMBRICO UHF S2
La Tabla 2ofrece un resumen de los sistemas con frecuencias compatibles en la banda
de 838,000 a 862,000 MHz. Cada grupo contiene canales múltiples, los cuales son
compatibles entre sí.
Hasta 20 sistemas inalámbricos UHF de Shure pueden funcionar simultáneamente en
la banda de los 838-862 MHz, si los sistemas son de versión de frecuencias KK (discontinuados), o una combinación de sistemas de versión KK y S2.
Hasta 30 sistemas inalámbricos UHF MK2 de Shure pueden funcionar simultáneamente en la banda de 838-862 MHz, si todos los sistemas son de versión de frecuencias S2.
Nota: Los transmisores UHF de Shure no están diseñados para funcionar con los receptores UHF MK2 de Shure, como tampoco los transmisores UHF MK2 de Shure están diseñados para funcionar con los receptores UHF de Shure. Siempre use transmisores y receptores de una misma versión de frecuencias (S2 ó KK).
Grupos 1-10 DEBEN usarse si la instalación incluye Sistemas inalámbricos UHF de
Shure (sólo versión de frecuencias KK) o Sistemas inalámbricos UHF de Shure y sistemas inalámbricos UHF MK2 de Shure (versiones de frecuencias KK y S2)
Grupos 1-10 PUEDEN usarse si la instalación incluye Sistemas inalámbricos UHF
MK2 de Shure (versiones de frecuencias S2).
Grupos 11-28 SOLAMENTE pueden usarse si la instalación incluye Sistemas inalámbricos UHF MK2 de Shure (versiones de frecuencias S2).
Nota: Este aparato es capaz de funcionar con algunas frecuencias no autorizadas para
su región. Por favor comuníquese con las autoridades nacionales para obtener información para el uso autorizado de micrófonos inalámbricos en su región.
CONTENIDO DEL GRUPO
Grupos 1-10*
El Grupo 1 contiene 10 frecuencias compatibles que se derivan de una combinación de
frecuencias de sitio fijo (UHF múltiples, altas y bajas), al igual que frecuencias de sitio
fijo para uso puertas adentro.
El Grupo 2 contiene 14 frecuencias de sitio fijo tomadas en su totalidad de las bandas
alta y baja múltiples de UHF (estas frecuencias NO son compatibles).
Los Grupos 3-4 proporcionan 10 frecuencias compatibles comprendidas dentro del canal 69 de TV (854-862 MHz).
Los Grupos 5-7 proporcionan 16 frecuencias compatibles comprendidas dentro de los
canales 68-69 de TV (846-862 MHz).
Los Grupos 8-10 proporcionan 16 frecuencias compatibles comprendidas dentro de los
canales 67-69 de TV (838-862 MHz).
Grupos 11-16
Los Grulpos 11-13 ofrecen el número máximo de frecuencias compatibles entre 838 y
862 MHz.
El Grupo 14 cumple con las regulaciones RegTP de Alemania para usuarios públicos
(“Nutzergruppe 4").
El Grupo 15 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
“Nutzergruppe 3A” dentro canales 67-69 de TV.
El Grupo 16 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
“Nutzergruppe 3B” dentro canales 67-69 de TV.
38
El Grupo 17 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
“Nutzergruppe 3C” dentro canales 67-69 de TV.
El Grupo 18 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
“Nutzergruppe 3D” dentro canales 67-69 de TV.
El Grupo 19 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
difusión de “Nutzergruppe 2" dentro canales 67-69 de TV.
El Grupo 20 cumple con las nuevas regulaciones RegTP de Alemania para usuarios de
difusión de “Nutzergruppe 1" dentro canales 67-69 de TV.
El Grupo 21 ofrece el número máximo de frecuencias compatibles entre 838 y 846 MHz
(canal 67 de TV)
El Grupo 22 ofrece el número máximo de frecuencias compatibles entre 846 y 854 MHz
(canal 68 de TV)
El Grupo 23 ofrece el número máximo de frecuencias compatibles entre 854 y 862 MHz
(canal 69 de TV)
El Grupo 24 contiene “frecuencias coordinadas” compatibles recomendadas según
“SET 1", según lo estipula JFMG**.
El Grupo 25 contiene “frecuencias coordinadas” compatibles recomendadas según
“SET 2", según lo estipula JFMG**.
El Grupo 26 contiene “frecuencias coordinadas” para uso PUERTAS ADENTRO.
Los Grupos 27-28 contienen “frecuencias coordinadas” para uso PUERTAS AFUERA.
*Comuníquese con la autoridad nacional para obtener información en cuanto a las
frecuencias legales disponibles y usos legales del equipo en su área.
** JMFG Limited es una empresa que ha sido contratada por la Agencia de
Radiocomunicaciones del Reino Unido desde abril de 1997 para administrar y otorgar
licencias sobre la parte del espectro radial utilizada para la preparación de programas y
eventos especiales en el Reino Unido.
39
TABLA 2
SISTEMAS CON FRECUENCIAS COMPATIBLES EN LA BANDA S2 (838 - 862 MHz)
CanalGrupo 1 Grupo 2 Grupo 3 Grupo 4 Grupo 5 Grupo 6 Grupo 7 Grupo 8 Grupo 9 Grupo 10
Minimo 152,4 m (500 piedi), in condizioni tipiche; 487.6 m, massimo.
NOTA: la portata effettiva di esercizio dipende dall'assorbimento, dalla riflessione e
dall'interferenza del segnale RF.
Risposta in audiofrequenza
Da 50 a 15.000 Hz, ±2 dB.
NOTA: la risposta in frequenza complessiva dipende dall'elemento microfonico.
Campo di regolazione del guadagno
U1: da 0 a 40 dB.
U2: da 0 a 26 dB.
Modulazione
Deviazione di ±18 kHz, sistema compressore-espansore con preenfasi e deenfasi.
Uscita di potenza RF
U1, U2: 10 mW massimo.
Gamma dinamica
>102 dB, ponderata A.
Reiezione della frequenza immagine
90 dB (valore tipico).
Reiezione dei segnali spuri
75 dB (valore tipico).
Sensibilità RF
U4SU4D
-110 dBm
12 dB SINAD
-105 dBm
30 dB SINAD
Silenziamento massimo (rif. deviazione di 18 kHz)
>100 dB, ponderato A.
Polarità audio
Una pressione positiva sul diaframma del microfono (o una tensione positiva applicata all'estremità della spina telefonica WA302) produce una tensione positiva sul
piedino 2 rispetto al piedino 3 dell'uscita a bassa impedenza e alla punta dell'uscita
da 1/4" ad alta impedenza.
Distorsione del sistema (rif. deviazione di ±18 kHz, modulazione di 1 kHz)
Distorsione armonica totale (TDH): 0,3% (valore tipico).
Alimentazione
U1, U2: pile alcaline AA da 1,5 V; pile NiCd opzionali.
U4: 230 V c.a., 50/60 Hz.
Consunzione di potenza: 9.6 W min; 13.2 W max (U4S)
12 W min; 16 W max (U4D)
15 W min; 16 W max (UA840)
Durata della batteria (valore tipico)
12 ore (con le pile alcaline AA da 1,5 V).
Campo della temperatura di esercizio
Da -6 a +49 °C
NOTA: le caratteristiche della batteria possono limitare questo campo.
-107 dBm
12 dB SINAD
-102 dBm
30 dB SINAD
42
Entrada de transmisor U1 (Figura 1)
Conector:TA4F o LEMO (opcional)
Configuración de entrada:Desequilibrada, activa
Impedancia real:18 kΩ con micrófono de corbata
Nivel máximo de entrada:6 Vp-p (+7 dBV) para 1% de THD usando señal de 1 kHz
Conexión de clavijas de
conector TA4F:
(en el cable adaptador para instrumento, la clavija 4 flota)
Conexión de clavijas de
conector LEMO:
Voltaje para potencia
fantasma:
1 MΩ con cable para instrumento
con ganancia en valor de ajuste mínimo
Clavija 1: Tierra
Clavija 2: +5 V
Clavija 4: 20 kΩ respecto a tierra y audio
Clavija 1: a Clavija 3 y 10 kΩ a tierra
Clavija 3: Audio
Clavija 2: +5 V
Clavija 3: Audio
Clavija 4: a escudo (tierra)
Suministro de +5 V al cartucho del micrófono
ELEMENTO
MICROFONICO
NOTA: PERMICROFONILAVALIER,IPIEDINI3E4SARANNO
COLLEGATI; NON LO SARANNO PER UN CAVO PER CHITARRA.
SCHEDA JACK MIC U1L (CONNETTORE LEMO A 4 PIEDINI)
2
2
4
4
3
3
1
1
1
2
3
4
499 &!
10K &!
499 &!
SCHEDA JACK MIC U1
500 &!
27 pF
27 pF
FIGURA 1
Uscita del trasmettitore U1
Connettore:SKK
Impedenza effettiva:50 Ω
Livello di uscita massimo:+11 dBm
Piedinatura:Guscio = Massa
Conduttore centrale = Segnale
500 &!
27 pF
20K &!
27 pF
AUDIO
POLARIZZAZIONE
SCHERMATURA
+5 V
AUDIO
MASSA
43
Ingresso del trasmettitore U2
Configurazione d'ingressoSbilanciata, attiva
Impedenza effettiva:20 kΩ
Livello di uscita massimo:3 Vp-p (+0.5 dBV) per una TDH dell'1% al valore minimo di
guadagno con un segnale a 1 kHz.
Uscita del trasmettitore U2
Connettore: SKK
Impedenza effettiva:50 Ω
Livello di uscita nominale:+10 dBm
Livello di uscita massimo:+11 dBm
Piedinatura:Guscio = Massa
Conduttore centrale = Segnale
Ingressi dei ricevitori U4S e U4D
Connettore:SMCAlimentazione
Tipo di connettore:BNCIEC 320“D” a 25 piedini
Impedenza effettiva:50 Ω ----
Livello d'ingresso
nominale:
Livello d'ingresso
massimo:
Piedinatura:Guscio = Massa
Tensione
alimentazione
remota:
Da -95 a -30 dBm230 V c.a., 50/60 HzLogica CMOS
+6 dBm (consigliati -20
12 V c.c., 150 mA max.----
dBm)
Conduttore centrale =
Segnale
d'ingresso
254 V c.a., 50/60 Hz--
A norma IEC--
Interfaccia di rete
Uscite dei ricevitori U4S e U4D
Connettore:MonitoraggioAlimentazion
Configurazion
e di uscita
Impedenza
effettiva:
Livello
d'ingresso
nominale:
Piedinatura:Punta =
Protezione di
tensione/
corrente/
alimentazione
virtuale?
*Livello di uscita: livello microfonico = livello di linea - 30 dB
Monofonica
sbilanciata,
1/4"
300 Ω--1 kΩ30 ΩVedi
--230 V c.a., 5
Tensione
Anello =j
Tension
Manicotto =
Massa
Si--SiSi5 V, 700 mA
e di uscita
--SbilanciataBilanciataVedi
A
A norma
IEC
Z audio altaZ audio bass*Interfaccia di
Appendice
Appendice
----Logica CMOS
Punta =
Tensione
manicotto =
44
Anello/
Massa
1 = Massa
2 = Tensione
3 =Tensione
Appendice
rete
Vedi
max.
Dimensioni complessive
U1: 92,2 x 64,7 x 24,2 mm (A x L x P)
U2/58: 228,6 x 51 mm (A x diam.)
U2/86: 213 x 49 mm (A x diam.)
U2/BETA 58A: 220,9 x 51 mm (A x diam.)
U2/87: 223,5 x 51 mm (A x diam.)
U2/BETA 87: 228 x 50 mm (A x diam.)
U4S/U4D: 44,5 x 482,6 x 295,3 mm (A x L x P)
Peso netto
U1: 175,2 g senza batteria
U2/58, U2/BETA 58A: 300 g senza batteria
U2/86: 332 g senza batteria
U2/87, U2/BETA 87: 339 g senza batteria
U4S: 3,30 kg; U4D: 3,85 kg
Omologazioni
I radiosistemi Shure serie UHF sono conformi ai requisiti essenziali specificati nella
direttiva europea R&TTE 99/5/EC e possono essere contrassegnati con il marchio CE.
U1, U2: Conforme alla norma ETSI europea EN 300 422 (partes 1 y 2) y ETS 300 445/
A1.
U4, U4D: Conforme alla norma ETSI europea ETS 300 422/A1 y EN 60950.
QUESTO APPARECCHIO RADIO è INTESO PER L'USO NELL'INTRATTENIMENTO A
LIVELLO PROFESSIONALE (CLASS I) E APPLICAZIONI SIMILI.
Eventuali modifiche di qualsiasi tipo non espressamente autorizzate dalla Shure Incorporated possono annullare il permesso di utilizzo di questo apparecchio. Chi usa l'apparecchio microfonico senza fili Shure ha la responsabilità di procurarsi la licenza adatta al suo impiego; la concessione di tale licenza dipende dalla classificazione dell'operatore, dall'applicazione e dalla frequenza selezionata. La Shure suggerisce vivamente
di rivolgersi alle autorità competenti per le telecomunicazioni riguardo alla concessione
della licenza appropriata e prima di scegliere e ordinare frequenze.
INFORMAZIONI SULLA CONFORMITÀ ALLA DIRETTIVA R&TTE
IMPORTANTE: I trasmettitori Shure modellos U1 e U2 conformen ai requisiti essen-
ziali specificati nella direttiva europea R&TTE 99/5/EC e possono essere contrassegnati con il marchio CE.
Il ricevitore Shure modello U4 conforme ai requisiti essenziali specificati nella direttiva
europea R&TTE 99/5/EC e possono essere contrassegnati con il marchio CE.
QUESTO APPARECCHIO RADIO è INTESO PER L'USO NELL'INTRATTENIMENTO
A LIVELLO PROFESSIONALE E APPLICAZIONI SIMILI.
NOTA: QUESTO APPARECCHIO PUò ESSERE IN GRADO DI FUNZIONARE A
FREQUENZE NON AUTORIZZATE NELLA REGIONE IN CUI SI TROVA L'UTENTE.
RIVOLGERSI ALLE AUTORITà COMPETENTI PER OTTENERE LE INFORMAZIONI
RELATIVE ALLE FREQUENZE AUTORIZZATE NELLA PROPRIA REGIONE PER I
PRODOTTI MICROFONICI SENZA FILI
Gamma di frequenza per questo apparecchio: 692 - 862 MHz
46
Concessione della licenza all'uso: Tenere presente che per usare questo apparecchio in certe aree può essere necessaria una licenza ministeriale. Per i possibili requisiti, rivolgersi alle autorità competenti.
I trasmettitorI Shure, modellos U1 e U2, può essere utilizzato nei Paesi e alle frequenze
elencati nella Tabella 1.
NOTA: la Shure suggerisce di mantenere una separazione di 500 kHz tra i canali dei ricevitori a
doppio canale U4D. Chiamate il servizio di assistenza clienti Shure (49-7131-72140) per richiedere ulteriori informazioni o assistenza nella selezione della frequenza e nella configurazione.
TABELLA 1
Codice del
Paese
A692-716
B692-716
CH692-716
D692-716
E692-716
F692-716
GB692-716
GR692-716
I692-716
IRL692-716
L692-716
NL692-716
P692-716
DK**800-810
FIN**800,1-810
N**800-810
S**800-810
Tutti gli altri
Paesi
U1-M3,
U2-M3
(692 - 716
MHz)
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
MHz*
******
U1-R3,
U2-R3
(774 - 782
MHz)
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
774-782
MHz*
(782 - 810
U1-R7,
U2-R7
MHz)
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
782-810
MHz*
MHz*
MHz*
MHz*
MHz*
U1-R6,
U2-R6
(800 - 820
MHz)
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
**838-862
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800-820
MHz*
800,1-819,9
MHz*
800-820
MHz*
800-814
MHz*
U1-R2,
U2-R2
(800 - 830
MHz)
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800-830
MHz*
800,1-819,9
MHz*
800-830
MHz*
800-814
MHz*
U1-S2, U2-S2
(838 - 862
MHz)
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
MHz*
838-862
MHz*
*
838-862
MHz*
838-862
MHz*
838-862
MHz*
838-862
MHz*
*
*
*
*
47
GUIDA ALLA COMPATIBILITÀ DEL RADIOSISTEMA UHF S2
La Tabella 2 fornisce una descrizione generale dei sistemi compatibili in frequenza nella banda compresa fra 838,000 e 862,000 MHz. Ciascun gruppo contiene più canali
compatibili fra loro.
Entro la banda 838-862 MHz possono funzionare contemporaneamente fino a 16 radiosistemi Shure UHF per frequenza KK (fuori commercio) o, in una combinazione di
sistemi, per le frequenze KK e S2.
Sempre entro questa banda possono funzionare contemporaneamente fino a 28 radiosistemi Shure UHF MK2 purché siano tutti nella versione per la frequenza S2.
Nota: le combinazioni di trasmettitori Shure UHF e ricevitori Shure UHF MK2, e di trasmettitori UHF MK2 e ricevitori Shure UHF NON possono essere usate insieme. Usare
combinazioni di trasmettitori/ricevitori per la stessa frequenza (S2 o KK).
Gruppi 1-10 DEVONO essere usati se l'installazione include Radiosistemi Shure UHF
(solo per la frequenza KK) oppure Radiosistemi Shure UHF e Shure UHF MK2 (per le
frequenze KK e S2)
Gruppi 1-10 POSSONO essere usati se l'installazione include solo radiosistemi Shure
UHF MK2 (per frequenza S2).
Gruppi 11-28 Possono essere usati SOLO se l'installazione include i radiosistemi
Shure UHF MK2 (per frequenza S2).
Nota: Questa apparecchiatura potrebbe funzionare a frequenze non autorizzate nella
regione in cui si trova l'utente. Rivolgersi alle autorità competenti per informazioni sulle
frequenze autorizzate localmente per i microfoni senza fili.
ELENCO DEI GRUPPI
Gruppi 1-10*
Il gruppo 1 contiene 10 frequenze compatibili, in una combinazione di frequenze per installazioni fisse (UHF alte e basse multiple) e per installazioni fisse in ambienti interni.
Il gruppo 2 contiene 14 frequenze per installazioni fisse, interamente appartenenti alla
banda di frequenze UHF alte e basse multiple (queste frequenze NON sono compatibili).
I gruppi 3-4 forniscono 10 frequenze compatibili comprese nel canale televisivo 69
(854-862 MHz).
I gruppi 5-7 forniscono 16 frequenze compatibili comprese nei canali televisivi 68-69
(846-862 MHz).
I gruppi 8-10 forniscono 16 frequenze compatibili comprese nei canali televisivi 67-69
(838-862 MHz).
Gruppi 11-28*
I gruppi 11-13 forniscono il numero massimo di frequenze compatibili fra 838 e 862
MHz.
Il gruppo 14 è compatibile con le norme tedesche RegTP per gli utenti pubblici (“Nutzergruppe 4") nei canali televisivi 67-69.
Il gruppo 15 è compatibile con le nuove norme tedesche RegTP per gli utenti di “Nutzergruppe 3A” nei canali televisivi 67-69.
Il gruppo 16 è compatibile con le nuove norme tedesche RegTP per gli utenti di “Nutzergruppe 3B” nei canali televisivi 67-69.
Il gruppo 17 è compatibile con le nuove norme tedesche RegTP per gli utenti di “Nutzergruppe 3C” nei canali televisivi 67-69.
48
Il gruppo 18 è compatibile con le nuove norme tedesche RegTP per gli utenti di “Nutzergruppe 3D” nei canali televisivi 67-69.
Il gruppo 19 è compatibile con le nuove norme tedesche RegTP per gli utenti della radiodiffusione di “Nutzergruppe 2" nei canali televisivi 67-69.
Il gruppo 20 è compatibile con le nuove norme tedesche RegTP per gli utenti della radiodiffusione di “Nutzergruppe 1" nei canali televisivi 67-69.
IL gruppo 21 forniscono il numero massimo di frequenze compatibili fra 838 e 846 MHz.
IL gruppo 22 forniscono il numero massimo di frequenze compatibili fra 846 e 854 MHz.
IL gruppo 23 forniscono il numero massimo di frequenze compatibili fra 854 e 862 MHz.
Il gruppo 24 contiene “frequenze coordinate” compatibili del “SET 1" raccomandato,
omologato dalla JFMG**.
Il gruppo 25 contiene “frequenze coordinate” compatibili del “SET 2" raccomandato,
omologato dalla JFMG**.
Il gruppo 26 contiene “frequenze coordinate” per l'uso in AMBIENTI INTERNI.
I gruppi 27-28 contengono “frequenze coordinate” per l'uso in AMBIENTI ESTERNI.
*Rivolgersi alle autorità competenti per informazioni sulle frequenze autorizzate localmente e
sulle norme che regolano l'uso delle apparecchiature.
** Nell'aprile 1997, la UK Radiocommunications Agency ha affidato alla JMFG Limited la
gestione dello spettro a radiofrequenza riservato alla produzione e agli eventi speciali nel
Regno Unito.
49
TABELLA 2
SISTEMI COMPATIBILI IN FREQUENZA NELLA BANDA S2 (838 - 862 MHz)
The Shure “Master List” (Groups A1-B4) is a comprehensive index of all system frequencies offered in the 838-862 MHz band, in 25 kHz increments.
LISTE MAÎTRESSE
La “Liste maîtresse” (groupes A1 à B4) est un index complet de toutes les fréquences
de systèmes utilisées dans la bande de 838 à 862 MHz, par tranches de 25 kHz.
HAUPTLISTE
Die Shure „Hauptliste“ (Gruppen A1-B4) enthält alle Systemfrequenzen, die im Frequenzbereich von 838 bis 862 MHz zur Verfügung stehen (in Stufen von 25 kHz).
LISTA MAESTRA
La “Lista maestra” de Shure (Grupos A1-B4) es un índice completo de todas las frecuencias ofrecidas en la banda de 838-862 MHz, en intervalos de 25 kHz cada uno.
L'ELENCO PRINCIPALE
L'elenco principale Shure (gruppi A1-B4) costituisce un indice completo di tutte le frequenze di sistema offerte nella banda 838-862 MHz, in incrementi di 25 kHz.
FREQ. (MHZ) GROUP
838.000A11
838.025A12
838.050A13
838.075A14
838.100A15
838.125A16
838.150A17
838.175A18
838.200A19
838.225A110
838.250A111
838.275A112
838.300A113
838.325A114
838.350A115
838.375A116
838.400A117
838.425A118
838.450A119
838.475A120
838.500A121
838.525A122
838.550A123
838.575A124
838.600A125
838.625A126
838.650A127
838.675A128
838.700A129
838.725A130
838.750A131
838.775A132
838.800A133
838.825A134
838.850A135
838.875A136
838.900A137
CHANNEL
FREQ. (MHZ) GROUP
838.925A138
838.950A139
838.975A140
839.000A141
839.025A142
839.050A143
839.075A144
839.100A145
839.125A146
839.150A147
839.175A148
839.200A149
839.225A150
839.250A151
839.275A152
839.300A153
839.325A154
839.350A155
839.375A156
839.400A157
839.425A158
839.450A159
839.475A160
839.500A161
839.525A162
839.550A163
839.575A164
839.600A165
839.625A166
839.650A167
839.675A168
839.700A169
839.725A170
839.750A171
839.775A172
839.800A173
839.825A174
52
CHANNEL
FREQ. (MHZ) GROUP
839.850A175
839.875A176
839.900A177
839.925A178
839.950A179
839.975A180
840.000A181
840.025A182
840.050A183
840.075A184
840.100A185
840.125A186
840.150A187
840.175A188
840.200A189
840.225A190
840.250A191
840.275A192
840.300A193
840.325A194
840.350A195
840.375A196
840.400A197
840.425A198
840.450A199
840.475A21
840.500A22
840.525A23
840.550A24
840.575A25
840.600A26
840.625A27
840.650A28
840.675A29
840.700A210
840.725A211
840.750A212
CHANNEL
FREQ. (MHZ) GROUP
840.775A213
840.800A214
840.825A215
840.850A216
840.875A217
840.900A218
840.925A219
840.950A220
840.975A221
841.000A222
841.025A223
841.050A224
841.075A225
841.100A226
841.125A227
841.150A228
841.175A229
841.200A230
841.225A231
841.250A232
841.275A233
841.300A234
841.325A235
841.350A236
841.375A237
841.400A238
841.425A239
841.450A240
841.475A241
841.500A242
841.525A243
841.550A244
841.575A245
841.600A246
841.625A247
841.650A248
841.675A249
841.700A250
841.725A251
841.750A252
841.775A253
841.800A254
841.825A255
841.850A256
841.875A257
841.900A258
841.925A259
841.950A260
841.975A261
842.000A262
842.025A263
842.050A264
842.075A265
842.100A266
842.125A267
842.150A268
842.175A269
842.200A270
842.225A271
842.250A272
842.275A273
842.300A274
842.325A275
842.350A276
842.375A277
842.400A278
842.425A279
CHANNEL
FREQ. (MHZ) GROUP
842.450A280
842.475A281
842.500A282
842.525A283
842.550A284
842.575A285
842.600A286
842.625A287
842.650A288
842.675A289
842.700A290
842.725A291
842.750A292
842.775A293
842.800A294
842.825A295
842.850A296
842.875A297
842.900A298
842.925A299
842.950A31
842.975A32
843.000A33
843.025A34
843.050A35
843.075A36
843.100A37
843.125A38
843.150A39
843.175A310
843.200A311
843.225A312
843.250A313
843.275A314
843.300A315
843.325A316
843.350A317
843.375A318
843.400A319
843.425A320
843.450A321
843.475A322
843.500A323
843.525A324
843.550A325
843.575A326
843.600A327
843.625A328
843.650A329
843.675A330
843.700A331
843.725A332
843.750A333
843.775A334
843.800A335
843.825A336
843.850A337
843.875A338
843.900A339
843.925A340
843.950A341
843.975A342
844.000A343
844.025A344
844.050A345
844.075A346
844.100A347
CHANNEL
FREQ. (MHZ) GROUP
844.125A348
844.150A349
844.175A350
844.200A351
844.225A352
844.250A353
844.275A354
844.300A355
844.325A356
844.350A357
844.375A358
844.400A359
844.425A360
844.450A361
844.475A362
844.500A363
844.525A364
844.550A365
844.575A366
844.600A367
844.625A368
844.650A369
844.675A370
844.700A371
844.725A372
844.750A373
844.775A374
844.800A375
844.825A376
844.850A377
844.875A378
844.900A379
844.925A380
844.950A381
844.975A382
845.000A383
845.025A384
845.050A385
845.075A386
845.100A387
845.125A388
845.150A389
845.175A390
845.200A391
845.225A392
845.250A393
845.275A394
845.300A395
845.325A396
845.350A397
845.375A398
845.400A399
845.425A41
845.450A42
845.475A43
845.500A44
845.525A45
845.550A46
845.575A47
845.600A48
845.625A49
845.650A410
845.675A411
845.700A412
845.725A413
845.750A414
845.775A415
CHANNEL
53
FREQ. (MHZ) GROUP
845.800A416
845.825A417
845.850A418
845.875A419
845.900A420
845.925A421
845.950A422
845.975A423
846.000A424
846.025A425
846.050A426
846.075A427
846.100A428
846.125A429
846.150A430
846.175A431
846.200A432
846.225A433
846.250A434
846.275A435
846.300A436
846.325A437
846.350A438
846.375A439
846.400A440
846.425A441
846.450A442
846.475A443
846.500A444
846.525A445
846.550A446
846.575A447
846.600A448
846.625A449
846.650A450
846.675A451
846.700A452
846.725A453
846.750A454
846.775A455
846.800A456
846.825A457
846.850A458
846.875A459
846.900A460
846.925A461
846.950A462
846.975A463
847.000A464
847.025A465
847.050A466
847.075A467
847.100A468
847.125A469
847.150A470
847.175A471
847.200A472
847.225A473
847.250A474
847.275A475
847.300A476
847.325A477
847.350A478
847.375A479
847.400A480
847.425A481
847.450A482
847.475A483
CHANNEL
FREQ. (MHZ) GROUP
847.500A484
847.525A485
847.550A486
847.575A487
847.600A488
847.625A489
847.650A490
847.675A491
847.700A492
847.725A493
847.750A494
847.775A495
847.800A496
847.825A497
847.850A498
847.875A499
847.900A51
847.925A52
847.950A53
847.975A54
848.000A55
848.025A56
848.050A57
848.075A58
848.100A59
848.125A510
848.150A511
848.175A512
848.200A513
848.225A514
848.250A515
848.275A516
848.300A517
848.325A518
848.350A519
848.375A520
848.400A521
848.425A522
848.450A523
848.475A524
848.500A525
848.525A526
848.550A527
848.575A528
848.600A529
848.625A530
848.650A531
848.675A532
848.700A533
848.725A534
848.750A535
848.775A536
848.800A537
848.825A538
848.850A539
848.875A540
848.900A541
848.925A542
848.950A543
848.975A544
849.000A545
849.025A546
849.050A547
849.075A548
849.100A549
849.125A550
849.150A551
849.175A552
54
CHANNEL
FREQ. (MHZ) GROUP
849.200A553
849.225A554
849.250A555
849.275A556
849.300A557
849.325A558
849.350A559
849.375A560
849.400A561
849.425A562
849.450A563
849.475A564
849.500A565
849.525A566
849.550A567
849.575A568
849.600A569
849.625A570
849.650A571
849.675A572
849.700A573
849.725A574
849.750A575
849.775A576
849.800A577
849.825A578
849.850A579
849.875A580
849.900A581
849.925A582
849.950A583
849.975A584
850.000A585
850.025A586
850.050A587
850.075A588
850.100A589
850.125A590
850.150A591
850.175A592
850.200A593
850.225A594
850.250A595
850.275A596
850.300A597
850.325A598
850.350A599
850.375A61
850.400A62
850.425A63
850.450A64
850.475A65
850.500A66
850.525A67
850.550A68
850.575A69
850.600A610
850.625A611
850.650A612
850.675A613
850.700A614
850.725A615
850.750A616
850.775A617
850.800A618
850.825A619
850.850A620
850.875A621
CHANNEL
FREQ. (MHZ) GROUP
850.900A622
850.925A623
850.950A624
850.975A625
851.000A626
851.025A627
851.050A628
851.075A629
851.100A630
851.125A631
851.150A632
851.175A633
851.200A634
851.225A635
851.250A636
851.275A637
851.300A638
851.325A639
851.350A640
851.375A641
851.400A642
851.425A643
851.450A644
851.475A645
851.500A646
851.525A647
851.550A648
851.575A649
853.525A728
853.550A729
853.575A730
853.600A731
853.625A732
853.650A733
853.675A734
853.700A735
853.725A736
853.750A737
853.775A738
853.800A739
853.825A740
853.850A741
853.875A742
853.900A743
853.925A744
853.950A745
853.975A746
854.000A747
854.025A748
854.050A749
851.600A650
851.625A651
851.650A652
851.675A653
851.700A654
851.725A655
851.750A656
851.775A657
851.800A658
851.825A659
851.850A660
851.875A661
851.900A662
851.925A663
851.950A664
851.975A665
852.000A666
CHANNEL
FREQ. (MHZ) GROUP
852.025A667
852.050A668
852.075A669
852.100A670
852.125A671
852.150A672
852.175A673
852.200A674
852.225A675
852.250A676
852.275A677
852.300A678
852.325A679
852.350A680
852.375A681
852.400A682
852.425A683
852.450A684
852.475A685
852.500A686
852.525A687
852.550A688
852.575A689
852.600A690
852.625A691
852.650A692
852.675A693
852.700A694
852.725A695
852.750A696
852.775A697
852.800A698
852.825A699
852.850A71
852.875A72
852.900A73
852.925A74
852.950A75
852.975A76
853.000A77
853.025A78
853.050A79
853.075A710
853.100A711
853.125A712
853.150A713
853.175A714
853.200A715
853.225A716
853.250A717
853.275A718
853.300A719
853.325A720
853.350A721
853.375A722
853.400A723
853.425A724
853.450A725
853.475A726
853.500A727
854.075A750
854.100A751
854.125A752
854.150A753
854.175A754
854.200A755
854.225A756
CHANNEL
FREQ. (MHZ) GROUP
854.250A757
854.275A758
854.300A759
854.325A760
854.350A761
854.375A762
854.400A763
854.425A764
854.450A765
854.475A766
854.500A767
854.525A768
854.550A769
854.575A770
854.600A771
854.625A772
854.650A773
854.675A774
854.700A775
854.725A776
854.750A777
854.775A778
854.800A779
854.825A780
854.850A781
854.875A782
854.900A783
854.925A784
854.950A785
854.975A786
855.000A787
855.025A788
855.050A789
855.075A790
855.100A791
855.125A792
855.150A793
855.175A794
855.200A795
855.225A796
855.250A797
855.275A798
855.300A799
855.325A81
855.350A82
855.375A83
855.400A84
855.425A85
855.450A86
855.475A87
855.500A88
855.525A89
855.550A810
855.575A811
855.600A812
855.625A813
855.650A814
855.675A815
855.700A816
855.725A817
855.750A818
855.775A819
855.800A820
855.825A821
855.850A822
855.875A823
855.900A824
CHANNEL
55
FREQ. (MHZ) GROUP
855.925A825
855.950A826
855.975A827
856.000A828
856.025A829
856.050A830
856.075A831
856.100A832
856.125A833
856.150A834
856.175A835
856.200A836
856.225A837
856.250A838
856.275A839
856.300A840
856.325A841
856.350A842
856.375A843
856.400A844
856.425A845
856.450A846
856.475A847
856.500A848
856.525A849
856.550A850
856.575A851
856.600A852
856.625A853
856.650A854
856.675A855
856.700A856
856.725A857
856.750A858
856.775A859
856.800A860
856.825A861
856.850A862
856.875A863
856.900A864
856.925A865
856.950A866
856.975A867
857.000A868
857.025A869
857.050A870
857.075A871
857.100A872
857.125A873
857.150A874
857.175A875
857.200A876
857.225A877
857.250A878
857.275A879
857.300A880
857.325A881
857.350A882
857.375A883
857.400A884
857.425A885
857.450A886
857.475A887
857.500A888
857.525A889
857.550A890
857.575A891
857.600A892
CHANNEL
FREQ. (MHZ) GROUP
857.625A893
857.650A894
857.675A895
857.700A896
857.725A897
857.750A898
857.775A899
857.800A91
857.825A92
857.850A93
857.875A94
857.900A95
857.925A96
857.950A97
857.975A98
858.000A99
858.025A910
858.050A911
858.075A912
858.100A913
858.125A914
858.150A915
858.175A916
858.200A917
858.225A918
858.250A919
858.275A920
858.300A921
858.325A922
858.350A923
858.375A924
858.400A925
858.425A926
858.450A927
858.475A928
858.500A929
858.525A930
858.550A931
858.575A932
858.600A933
858.625A934
858.650A935
858.675A936
858.700A937
858.725A938
858.750A939
858.775A940
858.800A941
858.825A942
858.850A943
858.875A944
858.900A945
858.925A946
858.950A947
858.975A948
859.000A949
859.025A950
859.050A951
859.075A952
859.100A953
859.125A954
859.150A955
859.175A956
859.200A957
859.225A958
859.250A959
859.275A960
859.300A961
56
CHANNEL
FREQ. (MHZ) GROUP
859.325A962
859.350A963
859.375A964
859.400A965
859.425A966
859.450A967
859.475A968
859.500A969
859.525A970
859.550A971
859.575A972
859.600A973
859.625A974
859.650A975
859.675A976
859.700A977
859.725A978
859.750A979
859.775A980
859.800A981
859.825A982
859.850A983
859.875A984
859.900A985
859.925A986
859.950A987
859.975A988
860.000A989
860.025A990
860.050A991
860.075A992
860.100A993
860.125A994
860.150A995
860.175A996
860.200A997
860.225A998
860.250A999
860.275B11
860.300B12
860.325B13
860.350B14
860.375B15
860.400B16
860.425B17
860.450B18
860.475B19
860.500B110
860.525B111
860.550B112
860.575B113
860.600B114
860.625B115
860.650B116
860.675B117
860.700B118
860.725B119
860.750B120
860.775B121
860.800B122
860.825B123
860.850B124
860.875B125
860.900B126
860.925B127
860.950B128
860.975B129
861.000B130
CHANNEL
FREQ. (MHZ) GROUP
861.025B131
861.050B132
861.075B133
861.100B134
861.125B135
861.150B136
861.175B137
861.200B138
861.225B139
861.250B140
861.275B141
861.300B142
861.325B143
861.350B144
861.375B145
861.400B146
861.425B147
861.450B148
861.475B149
861.500B150
861.525B151
861.550B152
861.575B153
861.600B154
861.625B155
861.650B156
861.675B157
861.700B158
861.725B159
861.750B160
861.775B161
861.800B162
861.825B163
861.850B164
861.875B165
861.900B166
861.925B167
861.950B168
861.975B169
862.000B170
CHANNEL
57
SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
In U.S.A., Phone: 1-847-600-2000 Fax: 1-847-600-1212
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414
In Asia, Phone: 1-852-2893-4290 Fax: 1-852-2893-4055
International Fax: 1-847-600-6446
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.