Shure ME930ED II User Guide

222

HARTREY

AYE..

EVANSTON.

IL. 60204

Q

MICROPHONES AND ELECTRONIC COMPONENTS

AREA

CODE

3121866.2200

TWX: 910-231-0048 TELEX: 72-4381

.

CABLE:

U.S

SHUREMICRO

THE PREMIER FAMILY OF STEREO SOUND REPRODUCERS

MODEL
ME930ED

11

STEREO DYNETIC@

PHONOGRAPH CARTRIDGE

CARTRIDGE AND STYLI SPECIFICATIONS

HZ - 22

20 to

within

5.0

N75ED

Type 2

5

X

18~

(.0002

.0007 in.)

Biradial
(Elliptical)

N75-31.

?%25 in.)
Spherical

toptional 78 rpm Stylus:
*Output voltages given for stereo cut record. For MONO cut record,

output voltage at both

will

'*Tracking forces greater than

NET

INDUCTANCE: 720

DC RESISTANCE: 630 ohms

OPTIMUM LOAD: 47,000 ohms resfstance in parallel with 400 to 500 p~co­farads total capacitance per channel. Load resistance can be up to 70,000
ohms with almost no audible change in frequency response. Total capaci­tance includes both tone arm

FOUR-CHANNEL: This Stereo
four-channel matrix systems.

MONOPHONIC OPERATION: Set function switch on amplifier to "MONO"
or
right channels in parallel.

CONNECTIONS (see Figure 1): Right "hot" lead (usually red) to "R," right
ground (usually green) to
left ground (usually blue) to
hum, remove the ground tab. The metallic cartridge shield is disconnected
from the right channel ground by the removal of the ground tab.

CAUTION: Do not make solder
connection to cartridge terminals,

STYLUS REPLACEMENT (see Fig­ure 2): Grasp molded housing of
stylus and gently pull forward out

of cartridge. Insert
stylus into socket and press until
housing mates with cartridge case.

MOUNTING [12.7 mm (1/2 in.)

mounting centers]:

Mounting screws are provided.

1.

2.

3.

4.

Copyright 1979. Shure Brothers
27A1446 (SE) Prlnted ~n U.S.A

Black

X

Dark

Green

be 71% of f~gures above.

WEIGHT:

"A+B."

Remove stylus guard and stylus
(see Stylus Replacement).
Connect leads to cartridge (see
Figure
Lay cartridge in shell and align
mounting holes on side of car­tridge with holes or threads in
shell. Follow turntable manu­facturer's instructions to mount
cartridge in tone arm or plug-in
shell.
Reinsert stylus (see Stylus Re- FIGURE
placement).

If ampl~fier is no1 equlpped with this swltch, connect left and

1).

mV

20,000

Hz

6.2 mV

20 to

20,000

Hz

Set arnplifier to "MONO" or

left channel and right channel cartridge terminals

maxlmum

6.2

grams
niilllhenries

wlring and arnplifier input circuit.

Dynetic@ cartridge is compatible with all

"RG

"

"LG."

replacemenl

25 dB

at

2 d~

-

1,000

Hz

-

to

grams

1%

to

grams

indicated

Left "hot" lead (usually white) to "L,"

If

metal head is causing ground loop

GROUND

Inc.

(OVER)

400

3/4

1,000 Hz

I!/..

10,000 Hz - 19 cm/sec

at 1 gram

3

"Ad-B."

should not be used.

1

FIGURE

2

C~/S~C

-

33

cm/sec

CHANNEL

GROUNDED

TO

CASE

A.

RECOMMENDED STYLUS CLEANING:
or smaller), trimmed to

alcohol-distilled

an
stylus damage or corrosion. Always brush stylus from back to front; never
brush or wipe stylus from front to back or side to side.

TO PRESERVE STYLUS LIFE:

1.

Follow turntable or tone arm instructions when adjusting antiskating
force.

2. Do not handle the tone arm while it is in operation since this may
cause the arm to sweep across the record.

1s necessary to manually place the tone arm in the record groove

3. If it
while turntable is rotating, release it as soon as the stylus engages the
record groove.

4. Correct improper set-down adjustment or malfunction of the turntable
changing mechanism to prevent the stylus from striking the edge of the
turntable or record. Do not stack more records than turntable manufac­turer recommends.

5. Take care to properly insert the stylus into the cartridge assembly and
cartrldge and shell assembly into the tone arm receptacle.

the

6. Use proper vertical

7.

Do not use badly warped, cracked or imperfect records.

8. When dusting the turntable protect the stylus with the stylus guard.

SPECIAL NOTE: To maintain the original performance standards
cartrldge, be certaln that any replacement stylus you buy bears the follow-

ina

certification

m;nufactured by Shure
WILL SERIOUSLY DEGRADE THE PERFORMANCE OF YOUR CARTRIDGE.
ALL GENUINE "DYNETICO" STYLI ARE MANUFACTURED
BROTHERS INC. LOOK

For more information on your Shure stylus, write for booklet:
the Small World of a Stylus."

FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated
222 Hartrey Avenue, Evanston, Illinois 60204, warrants to the owner of this
product that it will be free, in normal use, of any defects in workmanship
and materials
retain proof of date of purchase. Shure is not liable for any consequential
damages.
fully repack the unit and return it prepaid to:

If you are not in the United States, return the unit to your dealer or
Authorized Service Center for repair. The unit will be repaired or replaced
and returned to you promptly, and if it cannot be repaired or replaced,

you may elect to receive a refund. This warranty does not include stylus wear.

PATENT NOTICE:
of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.

for a period of one year from date of purchase. You should

If this Shure product has any defects as described above, care-

approximately

water solution. Commercial cleaning solutions may cause

tracklng force setting for each cartridge.

on the ~ackare: "This Stereo DvneticO stvlus is

roth hers

FOR

Shure Brothers lncorporated
Attention: Service Department
1501 West Shure Drive
Arlington Heights, Illinois 60004

Cartridge

Use a camel's hair brush (No. 2 size

6 mm (1/4 in.), dipped in alcohol or

of

your

Inc." AVOID

THE NAME SHURE ON THE STYLUS GRIP.

and stylus manufactured under one or more

INFERIOR

IM~TATIONS.

recision

BY

SHURE

"A

Visit to

YShure"),

THEY

Manufactured by Shure Brothers lncorporated

222

Hartrey Avenue, Evanston,

IL

60204