M951D SERIES:
M95HEID AND M95EDID
DESTATICIZER
CARTRIDGES
The M951D Series
With the Unique Shure Destaticizer
And Shure Side-Guard Stylus Protector
The M95HEID and M95EDID cartridges combine M95 performance and high trackability with the Shure Destaticizer whose
conductive carbon fibers ground static charges on the record
surface. An added bonus is the Side-Guard Stylus Protection
System which responds to accidental side thrusts on the stylus
by withdrawing the entire shank and tip safely into the stylus
housing before damage can occur.
OPERATION OF DESTATICIZER OPERATION OF SIDE-GUARD
3
Because the Destaticizer excludes static from the amplifier and
speakers, static-caused clicks and pops are eliminated from the
audio system. In addition, the conductive fibers prevent static
charges, either on the record or on the turntable dustcover, from
attracting or repelling the tone arm. The arm-to-record distance,
the tracking angle, and the tracking force remain constant; and
the cartridge retains its full potential tracking ability.
The Destaticizer's tiny groove-contact fibers reach down into the
groove and sweep away interfering dust and grit. The
Destaticizer contains more than 10,000 individual fibers with an average
diameter of
clean before the stylus reaches it, the stylus tracks the groove
7.6~
(.00(13 in.) each. Because the groove is swept
and not the dust. Reproduction is enhanced, and both record and
stylus life are prolonged, because the dust particles are prevented from abrading either the groove or the diamond tip.
Two
M951D Models are available:
The
M95HEID has a distortion-reducing nude hyperelliptical dia-
mond tip and tracking force of
The
M95EDlD has a nude biradial (elliptical) diamond tip and
tracking force of to
1
W
grams.
to 1% grams.
STYLUS REMOVAL AND REPLACEMENT
A
FIGURE
FIGURE
1
EFT
CYML
li(l,E
LEFT
CWNHEL
GRWD
BUL
2
IMPORTANT: Always remove the stylus before making connections or mounting the cartridge. The cartridge's Destaticizer
should be in the "guard" position throughout. Exercise care so
your fingers don't slip and damage the stylus tip or shank.
ELECTRICAL CONNECTIONS
MIGHT
CHANNEL
SR0"ND
RITHT
CHON
RED
Connect the cartridge as shown. In many tone arms, lead wiring
is color coded and matches this cartridge's color coded terminals.
MOUNTING
Mounting centers are standard
ware is provided. Refer to the tone arm manual for specific
details, such as the need for spacers.
The two basic mounting methods are:
1.
Mounting the cartridge in a tone arm shell that has unthreaded
clearance holes.
2.
Mounting the cartridge in a tone arm shell that has threaded
mounting holes.
12.7
mm
(%").
Mounting hard-
THREADED
HOLES
CARTRIDGE MOUNTING, METHOD
*Top of cartridge mounting block should be parallel to record.
Use spacers if necessary.
J
6
CARTRIDGE MOUNTING, METHOD
FIGURE
3
1
FIGURE
4
X
CARTRIDGE LEVELING
FIGURE
5
2
SURFACE
CONDUCTIVE>
FIBERS
'::.{:,
civ',GunRD"
FIGURE
6
TRACKING FORCE
These cartridges are designed for a stylus tip tracking force
range of 0.75 to 1.5 grams. When the Destaticizer rests on the
record in the operating position, it exerts a downward force of 0.5
grams that must also be accommodated in the total tone arm
tracking force setting. Therefore, set the tracking force as
follows.
obta~n this force at
To
the stylus tip adjustment to
0.75 grams 1.25 grams
1.0 gram 1.5 grams
1.5 grams 2.0 grams
Set the arm tracking force
8
When using an external gauge (such as the Shure SFG-2 Stylus
Force Gauge), rest both the stylus tip and the Destaticizer brush
on the balance beam and set the force for the total tone arm setting (right hand column above). When the Destaticizer rides on
the record with the cartridge in use, the extra 0.5 grams will be
offset by the Destaticizer and
STYLUS TIP. The tip force will be that shown in the left hand
column.
WILL NOT APPEAR AT THE
SKATING COMPENSATION
Set the antiskate mechanism according to the tone arm manufacturer's directions. Use an antiskating force corresponding to
the total tone arm tracking force (right hand column above).
OPERATION
For optimum playing position, the top edge of the mounting
block should be parallel to the record. The white cue stripe on
the Destaticizer assists in accurate set down by showing the
stylus tip position.
9
SPECIFICATIONS
Frequency Response
20 to 20,000 Hz
Output (at 1,000 Hz)
4.7
mV at 5 cmlsec peak recorded velocity (Output voltage
given for stereo cut record. For mono cut record, output voltage at both left channel and right channel cartridge terminals
will be 71% of the above figure.)
Channel Separation (minimum)
25 dB at 1 kHz
Channel Balance
Within 2 dB
Tip Tracking Force'
0.75 to 1.5 grams
Total Tone Arm Tracking Force (Destaticizer on record)'
1.25 to 2.0 grams
Force Exerted by Destaticizer
0.5 grams
'See section on tracking force
10
Typical Trackability (in cmlsec peak recorded velocity)
400 Hz-24 cmlsec
1,000 Hz-33 cmlsec
10,000 Hz-19 cmlsec
Inductance
700 millihenries
DC Resistance
1550 ohms
Optimum Load
47,000 ohms resistance in parallel with 200 to 300 picofarads
capacitance per channel. Load resistance can be up to 70,000
ohms with almost no audible change in frequency response.
Total capacitance includes both tone arm wiring and amplifier
input circuit.
Net Weight
6.4 grams
Replacement Styli
M95HUD: N95HEID Stylus, ivory lettering on black nameplate;
distortion-reducing nude hyperelliptical tip, 5
,0015 in.); 0.75 to 1.5 grams tip tracking force
M95EDID: N95EDID Stylus, yellow lettering on black nameplate; nude biradial (elliptical) tip, 5
0.75 to 1.5 grams tip tracking force
at 1 gram tip tracking force
x
38p (.0002
x
18p (.0002 x ,0007 in.);
x
CLEANING
To clean the Destaticizer,
with the cartridge.
To clean the stylus, use the brush supplied with the cartridge
with alcohol or an alcohol-distilled water solution.
Brush only from back to front as shown. Commercial cleaning
solutions may cause stylus damage.
To maintain the original performance standards of your cart-
ridge, be certain that any replacement stylus you buy bears the
following certification on the package: "This Stereo
stylus is precision manufactured by Shure Brothers Inc." AVOID
INFERIOR IMITATIONS. THEY
PERFORMANCE OF YOUR CARTRIDGE. ALL GENUINE
"DYNETICD" STYLI ARE MANUFACTURED BY SHURE
BROTHERS INC. LOOK FOR THE NAME SHURE ON THE
STYLUS GRIP.
use
no
fluids.
Use the brush supplied
WILL SERIOUSLY DEGRADE THE
Dynetica
12
DEMONTAGE
Important: toujours retirer la pointe avant d'etablir les raccordements
ou de monter la cellule. Le dispositif
lours se trouver en posit~on de protection (voir figure
que les
de la
I
Rdccorder la cellule comrne sur la flgure 2 Dans de nombreux bras de
lecture,
Ies bornes da raccordement de cette cellule
1
MONTAGE DE LA CELLULE
L'ecartement du milieu des trous pour monter la cellule est de
Les pieces permettant son montage sont
reporter au mode d'emploi du bras de lecture pour davantage de
details, par exemple si
Ne pas replacer la pointe avant d'avoir
triques et termine le montage.
II existe deux methodes de montage de base:
1.
Montage de la cellule sur une coquille de bras de lecture qui possi.de
des trous non
2.
Montage de la cellule sur une coquille de bras de lecture avec trous
taraudes.
ET MONTAGE DE LA POlNTE
ant~statique de la cellule doit tou-
dolgts ne glissent pas et n'endommagent pas la pointe ou la tige
polnte.
les llgnes d'amenee sont codees dans les m@mes couleurs que
ltvrees avec la cellule. (Se
I'on a besoin de rondelles d'ecartement).
etabli les raccordements elec-
filetes.
1).
Veillez a ce
12,7
mm.
v
PATENT NOTICE
Cartridge and stylus manufactured under one or more of the following U.S. Patents:
3,463,889: 4,194,744: 4,275,888:
D235,070; D235,351; D235,352; D245,022; D245.433; 0252,628;
D254,004; D257.676; D255,898; D258,586;
FULL
0NE.YEAR WARRANTY
Shure Brothers lncorporated ("Shure"),
Evanston, Illinois
that it will be free, in normal use, of any defects in workmanship
and materials for a period of one year from date of purchase. You
should retain proof of date of purchase. Shure is not liable for
any consequential damages If this Shure product has any
defects as described above, carefully repack the unit, have it
insured, and return it prepaid to:
If you are not in the United States, return the unit to your dealer
or Authorized Service Center for repair. The unit will be repaired
or replaced and returned to you promptly and, if it cannot be
repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear.
Copyright
27A1790(BG)
1982,
3,055,988; 3,077,521; 3,077.522; 4,270,758;
60204,
Shure Brothers lncorporated
Attention: Service Department
222
Hartrey Avenue
Evanston, Illinois
Shure Brothers Inc.
D193,854: D193,934; D201,803;
other patents pending.
222
warrants to the owner of this product
60204
Hartrey Avenue,
Printed in U.S.A.
Loading...