Shure GLXD1, GLXD2, GLXD4, GLXD6 Specifications
System Specifications
Tuning Bandwidth |
2400–2483.5 MHz |
|
RF Carrier Range |
Group |
1: 2404–2478 MHz |
|
|
2: 2404–2478 MHz |
|
|
3: 2405–2477 MHz |
Working Range |
60 m (200 ft) typical Note: Actual range depends on RF signal absorption, reflection and interference. |
|
|
|
|
Bandwidth |
Group |
1: 1.2 MHz |
|
|
2: 1.2 MHz |
|
|
3: 2.2 MHz |
Transmit Mode |
Frequency Hopping |
|
|
|
|
Audio Frequency Response |
20 Hz – 20 kHz Note: Dependent on microphone type |
|
Dynamic Range |
120 dB, A-weighted |
|
|
|
|
Latency |
Group |
1: 3.9 ms |
|
|
2: 7.3 ms |
|
|
3: 7.3 ms |
RF Sensitivity |
-88 dBm, typical |
|
Total Harmonic Distortion |
0.2%, typical |
|
|
|
|
RF Output Power |
10 mW E.I.R.P. max |
|
|
|
|
Operating Temperature Range |
-18°C (0°F) to 57°C (135°F) Note: Battery characteristics may limit this range. |
|
Storage Temperature Range |
-29°C (-20°F) to 74°C (165°F) |
|
|
|
|
Polarity |
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low-impedance output) |
|
|
and the tip of the high impedance 1/4-inch output. |
|
|
|
|
Battery Life |
Up to 16 hours |
|
|
|
|
|
NOTE: All Specifications are subject to change. Performance may vary depending on country regulations and operating environment. |
|
Component Specifications
GLXD1 Bodypack Transmitter |
Dimensions |
90.4 x 64.5 x 22.9 mm (3.56 x 2.54 x 0.90 in.), H x W x D (without antenna) |
||||||||||
|
|
|
|
|
|
|
Power Requirements |
3.7 V Rechargeable Li-Ion |
|
|
|
|
|
|
|
|
|
|
|
Housing |
Cast Metal, Black Powdercoat |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Impedance |
900 k |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RF Output Power |
10 mW E.I.R.P. max |
|
|
|
|
|
|
|
|
|
|
|
Transmitter Input |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connector |
4-Pin male mini connector (TA4M) |
|
|
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
Configuration |
Unbalanced |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Input Level |
−8.4 dBV (7.5 Vp-p) |
|
|
|
|
|
|
|
|
|
|
|
(1 kHz at 1% THD) |
|
|
|
|
|
|
|
|
|
|
|
|
Antenna Type |
Internal Monopole |
|
|
|
|
|
|
|
|
|
|
|
Pin Assignments |
1: Ground (cable shield) |
|
|
|
|
|
|
|
|
|
|
|
TA4M |
2: + 5 V Bias |
|
|
|
|
|
|
|
|
|
|
|
|
3: Audio |
|
|
|
|
|
|
|
|
|
|
|
|
4: Tied through active load to ground (On instrument adapter cable, pin 4 floats) |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GLXD2 Handheld Transmitter |
Dimensions |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
A |
B |
C |
|
|
|
|
|
|
|
|
|
SM58 |
51 mm, 2.0 in. |
252 mm, 9.9 in. |
37 mm, 1.5 in. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BETA 58 |
51 mm, 2.0 in. |
252 mm, 9.9 in. |
37 mm, 1.5 in. |
|
|
|
|
|
|
|
|
|
SM86 |
49 mm, 1.9 in. |
252 mm, 9.9 in. |
37 mm, 1.5 in. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BETA87A |
51 mm, 2.0 in. |
252 mm, 9.9 in. |
37 mm, 1.5 in. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight
GLXD2 |
on |
|
SM58 |
267 g (9.4 oz.) without batteries |
|
BETA 58 |
221 g (7.8 oz.) without batteries |
|
SM86 |
275 g (9.1 oz.) without batteries |
|
|
|
|
BETA87A |
264 g (9.3 oz.) without batteries |
Housing |
Molded Plastic |
Power Requirements |
3.7 V Rechargeable Li-Ion |
|
|
RF Output Power |
10 mW E.I.R.P. max |
Maximum Input Level |
145 dB SPL |
|
|
www.shure.com |
©2013 Shure Incorporated |
Loading...