Shure AXS31, AXS58 User Manual
English
Accessories
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁ
БББББ
БББББ
ÁÁ
ÁÁ
БББББ
БББББ
БББББ
БББББ
БББББ
БББББ
Á
Á
Á
Á
Á
ÁÁ
Á
ÁÁÁ
Á
ÁÁ
Á
Á
Á
ÁÁ
ÁÁ
Á
ACCESS VHF SERIES USER GUIDE
This user guide provides detailed instructions for your Access VHF series wireless system. To get your system up and
running in minutes, see the Access VHF Series Quick Set Up Guide.
Your new Access VHF Series system is designed to give you both the freedom of a wireless system and world-famous
Shure sound quality . This manual covers both Single antenna and Diversity versions of the Access VHF Series systems:
the AXS31/58 handheld systems; the AXSGW bodypack systems; the AXSHW Headset systems; and the AXSLWD lavalier microphone system.
Wireless
System
AXS31 and AXS58
Hand-held systems for
singers.
Bodypack systems for elec-
tric and bass guitarists. Can
AXSGW
also be used with other elec-
Components
Transmitter AXH2 Handheld
Microphone SM58 or BG3.1 –– WH20 Headset
Receiver AXR3 single antenna or AXR4N Diversity
Power Supply PS20 (105–125 VAC, 60 Hz)
Supplied
Accessories
Transmitter
Carrying and storage case; Receiver feet; Hook and loop fastening strips; gain adjustment screwdriver
microphone stand adapter 1/4” to 1/4” guitar cables (2)
tric instruments
AXB1G Bodypack
Transmitter
RECEIVER FEATURES
6
8
5
8
6
1
2
3
4
AXR3 AXR4N
7
1
2
AXSHW
Bodypack system for ap-
plications requiring hands-
free operation, such as aero-
bics or percussion
Microphone
UNBALANCE D
HIGH Z
5
.
.
.
.
.
.
.
.
.
3
4
.
BALANCED
AXSLWD
Bodypack system for public
speaking, theater, or busi-
ness presentations.
AXB1 Bodypack
Transmitter
WL93 omnidirectional
lavalier
7
SHURE BOTHERS INC.
EVANSTON IL 60202 USA
SQUELCH
DC INPUT
12–18 VDC
MIN MAX
9
1. Power On Indicator: Glows green when the receiver is
powered on.
2. RF Signal Indicator:
frequency) signals are received.
tor lights glows when RF is received by antenna A or B.
3. Audio Peak Indicator: Flashes red when the audio signal
received approaches overload clipping level.
4. Volume Control: Adjusts the output volume of the receiver.
Does not affect Transmitter Audio Peak indicator.
5. Telescoping Antenna(s): Receives signals from the trans-
mitter.
FIGURE 1. AXR3 AND AXR4N RECEIVER FEATURES
AXR3
: Glows yellow when RF (radio
AXR4N
: One of two indica-
6. Audio Output: Provides mic level signal for connection to
amplifiers or mixing consoles.
AXR4N
: 1/4 inch phone jack and male XLR connector.
AXR3
: 1/4 inch phone jack.
7. Squelch Control: This control is factory pre-set and normally requires no adjustment. See
ments
at the end of this guide.
Wireless System Adjust-
8. Power Input: Accepts power from supplied AC adapter.
9. Power Cable Retainer:
AXR4N
only. Secures the AC
adapter cable to the receiver.
1
English
Á
Á
ÁÁÁÁÁ
TRANSMITTER FEATURES
3
4
5
6
1
2
10
7
8
9
11
9
AXB1/AXB1G
Bodypack
FIGURE 2. AXB1, AXB1G, AND AXB11 BODYPACK TRANSMITTER FEATURES
1. Battery Compartment. Holds one 9V alkaline battery.
2. Antenna. For best operation, the antenna
cally, and should not be coiled or bundled.
3. Belt Clip. Secures the transmitter to a belt, waistband or guitar strap.
4. Power On Indicator . Glows green when transmitter is powered on.
5. Power Switch. Recessed to prevent accidental turn-off.
6. Mute Switch. Slide to ON for normal operation. Slide to
MUTE to prevent sounds from being transmitted to the receiver
. Muting the transmitter does not turn off transmitter
power.
7. Low Battery Indicator. Glows red when one hour or less of
must
hang verti-
AXB1G
operating time remains and transmitter battery should be
changed.
8. Audio Gain Control. Provides audio level adjustment to ac-
commodate dif ferent sound sources (e.g., speaking or playing an instrument). A small screwdriver is supplied to make
adjustments.
9. Input Connector. AXB1: Tini Q-G
connector provides
connection to a variety of lavalier and headset microphone
cables and to the Shure WA302 instrument adapter cable.
AXB1G: Accepts a standard 1/4 inch or guitar cable plug.
10. Lavalier Microphone. WL93 omnidirectional condenser
microphone supplied with a mount that clips onto a tie, lapel,
or acoustic instrument.
11. Cables. AXB1G: 1/4 inch to 1/4 inch guitar cable for electric
guitar or other electric instruments.
5
6
1
2
3
4
FIGURE 3. AXH2 MICROPHONE-TRANSMITTER FEATURES
1. Power Switch. Recessed to prevent accidental turn-off.
2. Power On Indicator. Glows green when power is on.
3. Low Battery Indicator. Glows red when one hour or less of
operating time remains and battery should be changed.
4. Mute Switch. Slide to ON for normal operation. Slide to
MUTE to prevent sounds from being transmitted to the receiver.
Muting the transmitter does not turn off power
.
7
5. Audio Gain Control. Allows you to adjust the transmitter to
match the loudness of your vocals. A small screwdriver is
supplied to make adjustments.
6. 9V Alkaline Battery (shown installed). Provides power to
the microphone-transmitter.
7. Battery Cover. Unscrews for access to the 9V alkaline bat-
tery and gain control.
2
SYSTEM SETUP
Á
ÁÁÁÁÁÁ
ÁÁÁÁÁ
Á
Á
Á
Á
Á
ÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁ
Á
Á
Á
English
BATTERY INSTALLATION
1. Slide the transmitter POWER ON/OFF switch to the OFF
position.
AXB1, AXB1G
2.
compartment cover, slide it back and flip it open, as shown
in Figure 4.
AXH2:
Unscrew the transmitter battery cover to expose the
battery terminals, as shown in Figure 3.
3. Insert a fresh 9V alkaline battery into the battery compartment ( A Du ra cel l M N 1604 i s recommended). A fresh 9V alkaline battery will typically provide 18 hours of performance
time. A fully charged 8.4V NiCad battery will provide about
2 hours of performance time.
IMPORT ANT: Carbon-zinc and zinc-chloride batteries will
not provide adequate power and are not recommended.
4. Replace the battery cover.
: Press down on the OPEN side of the battery
9 V
-
+
FIGURE 4. BATTERY INSTALLATION
BODYPACK TRANSMITTER SETUP
1. Attach the transmitter to your belt, guitar strap, or waistband
as shown in Figure 6. Depress the tab marked PRESS and
slip the belt or strap between the transmitter body and the
belt clip. For added stability, draw the strap or belt toward the
clip’s top wire, especially when using thin guitar straps.
AXB1/AXB1G
FIGURE 6. TRANSMITTER SETUP
2. Plug your guitar, headset microphone, or lavalier microphone into the transmitter.
RECEIVER SETUP
1. Plug one end o f the AC p ower a dapter i nt o t he D C INPUT c onnector on the back of the rece iver.
cable around the cable retai ner on the bottom of the r ecei ver.
See Figur e 7 . Plug t he o t her end int o a n A C p ow er s our ce ( use
PS20 for 105–125 VAC. The green POWER light on the receiver will glow.
AXR4N
: Loop the power
HEADSET ASSEMBLY
1. Refer to the tag attached to the headset for assembly instructions. After assembling the WH20, adjust the headband and place it on your head.
2. Position the microphone over the corner of your mouth,
about 1/2 inch away. See Figure 5.
3. To reduce pops and breath noise, place the supplied foam
windscreen over the microphone.
FIGURE 5. HEADSET MICROPHONE POSITION
12
FIGURE 7. AXR4N POWER CABLE RETAINER
2. Connect the receiver output. The Guitarist: plug a standard
guitar cable (two provided) into the receiver’s output connector. Plug the other end into a guitar amplifier, as shown
in Figure 8. AXSHW, AXS31, AXS58 or AXSLWD: Use a
cable with a 1/4 inch phone plug (
male XLR connector (
AXR4N
mic level input of a mixer or P A system, as shown in Figure
8.
3. Extend antenna(s).
AXR3
: The antenna should be fully extended and vertical, as shown in Figure 8.
tennas should be fully extended and angled away from each
other, at an angle of 45 degrees from vertical, as shown in
Figure 8.
AXR3, AXR4N
) or a fe-
) to connect the receiver to a
AXR4N
: The an-
3
Loading...