How it Works
Shure
Loading...
ADX1
User Manual
26 pgs761.62 Kb0
Table of contents
Loading...

Shure ADX1 User Manual

ADX1
Bodypack Transmitter
ADX1 Enhanced Bodypack Transmitter User Guide
Version: 7 (2019-D)

Table of Contents

Shure Incorporated
Audio Menu 12
Utilities Menu 12
IR Sync 13
Setting the Frequency Manually 14
Wearing the Bodypack Transmitter 14
RF Mute 15
Safe Start 15
Input Overload 16
Matching Audio Levels with Mic Offset 16
Tone Generator 17
ShowLink Test 17
Updating Firmware 18
Firmware Versioning 18
Updating the Transmitter 18
Specifications 18
Input Connector Diagrams 21
Frequency Bands and Transmitter RF Power 22
LICENSING INFORMATION 24
Australia Warning for Wireless 24
Certifications 25
Information to the user 26
2/26

ADX1 Bodypack Transmitter

WARNING

◦
Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify,
disassemble, heat above 140°F (60°C), or incinerate.
◦
Follow instructions from manufacturer
◦
Only use Shure charger to recharge Shure rechargeable batteries
◦
WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
Shure Incorporated
◦
Never put batteries in mouth. If swallowed, contact your physician or local poison control center
◦
Do not short circuit; may cause burns or catch fire
◦
Do not charge or use battery packs other than Shure rechargeable batteries
◦
Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
◦
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or
the like
Note: Use only with the included power supply or a Shure-approved equivalent.

ADX1 Axient Digital Bodypack Transmitter

ADX series transmitters deliver impeccable audio quality and RF performance, and are equipped with ShowLink remote
control for real-time parameter adjustments and interference avoidance. This transmitter features wide tuning, High Density
(HD) mode, encryption, and advanced rechargeability in a streamlined design. Light-weight aluminum construction, AAA or
SB910 rechargeable power options (with lockable charging), and TA4 or LEMO3 connector options.
®

Features

Performance

◦
184 MHz tuning range
3/26
◦
20 Hz to 20 kHz range with flat frequency response
◦
Automatic input staging optimizes gain setting
◦
Diversity ShowLink-enabled for remote transmitter control and automatic interference avoidance
◦
AES 256-bit encryption-enabled for secure transmission
◦
>120 dB, A-weighted, System Gain @ +10
◦
Digital output: >125dB, A-weighted (Dante, AES3, AES67)
◦
100 meter (300 feet) line-of-sight operating range
◦
Selectable modulation modes optimize performance for spectral efficiency
Standard – optimal coverage, low latency
◦
High density – dramatic increase in max system channel count
◦
Built-in tone generator and RF markers to facilitate walk-testing
Shure Incorporated
◦
◦

Design

◦
◦
◦
◦
◦
Switchable Power Levels = 2/10/40 mW (region dependent)
Frequency Diversity selection using two bodypacks
TA4 or LEMO3 audio connector option
Backlit LCD with easy to navigate menu and controls
Durable, moisture-resistant, lightweight metal case
Flexible ¼ wave antenna
Menu and power lockout

Power

◦
◦
◦
Shure SB910 rechargeable batteries for up to 10 hours of runtime, precision metering, and zero memory
effect
AAA-compatible battery sled available
External charging contacts for docked charging
4/26

Included Components

SB910 Shure Rechargeable Battery (2) 95A24832
¼ wave antenna Varies by Region
Transmitter carrying case WA610
Belt clip 44A28563
Zipper bag 95A2313

Optional Accessories

SB910 Shure Rechargeable Battery 95A24832
Shure Incorporated
3 x AAA Battery Sled for ADX1 Transmitter SB913
AD651FOB Talk Switch fob for bodypack transmitters 90A37348
Replacement belt clip 44A28563
Shure Networked Docking Charger 2-Up SBC240

ADX1 Transmitter Overview

① RF Antenna
For RF signal transmission.
② Display
View menu screens and settings. Press any control button to activate the backlight.
③ Control Buttons
Use to navigate through parameter menus and to change settings.
④ Battery Compartment
Requires Shure SB910 rechargeable battery.
⑤ Battery Door
Latching door to secure battery.
⑥ SMA Connector
Connection point for RF antenna.
⑦ Infrared (IR) Port
5/26
Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup.
⑧ Power Switch
Powers the unit on or off.
⑨ Power LED
Green = unit is powered on
◦
Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting)
⑩ Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Note: A LEMO connector model variation of this transmitter is available.
⑪ Battery Charging Contacts
Charging contacts for use with docking battery chargers.
Shure Incorporated

Transmitter Controls

Use the controls to navigate through parameter menus and change values.
6/26
X Acts as a 'back' button to return to previous menus or parameters without confirming a value change
O Enters menu screens and confirms parameter changes
∨∧ Use to scroll through menu screens and to change parameter values
Tip: Use the following shortcuts for quick setup:
◦
Hold the ∧ button while powering on to lock or unlock the transmitter.
◦
Hold the X button while powering on to enter the Safe Start menu.
Shure Incorporated

Locking the Interface

Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon appears on the
home screen when the interface lock is enabled.
1.
From the Utilities menu, navigate to Locks and select one of the following lock options:
None: The controls are unlocked
Power: The power switch is locked
Menu: The menu parameters are locked
◦
All: The power switch and menu parameters are locked
2.
Press O to save.
Tip: To quickly unlock a transmitter: Press O twice, select None, and press O.

Home Screen Display

The home screen shows transmitter information and status.
There are four pieces of information that you can choose to see on the home screen. Use the arrow buttons to select one of
the following choices:
Name
Frequency Setting
Group (G) and Channel (C)
Device ID
The following icons indicate transmitter settings:
7/26
Shure Incorporated
Battery runtime in hours and minutes or bar display
Key: Displayed when encryption is enabled
Lock: Displayed when controls are locked. Icon will flash if
access is attempted to a locked control (power or menu).
ShowLink signal strength displays 0 to 5 bars
STD: Standard Transmission Mode
HD: High Density Transmission Mode
RF Mute Engaged: Displayed when RF output is muted

Shure Rechargeable Batteries

Shure lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50% capacity
in one hour and reach full charge within three hours.
Single chargers and multiple bay chargers are available to recharge the Shure batteries.
Caution: Only charge Shure rechargeable batteries with a Shure battery charger.

Checking Battery Info

When using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours and minutes
remaining.
Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery
◦
Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)
◦
Bars: Indicates the number of bars displayed
◦
Time: Battery runtime
◦
Charge: Percentage of charge capacity
◦
Health: Percentage of current battery health
◦
Cycle Count: Total of the number of charging cycles for the installed battery
◦
Temperature: Battery temperature reported in Celsius and Fahrenheit
8/26
Loading...
+ 18 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use