Shure A88SM User Guide

GENERAL

The Shure Model A88SM Microphone Isolation Mount provides
exceptional freedom from mechanically transmitted noise. Its high­ly effective Shock-Stopper
ble locking device eliminates most noise associated with stands,
booms, and cable movement. Designed expressly for Shure’s
VP88 MS Stereo Condenser Microphone, the A88SM can also be
used with any microphone with a handle diameter of approximately
27 mm (1

mount for instant attachment to most ENG cameras with a mount­ing “shoe.” A simple twist knob provides positive-locking vertical
angle adjustment. A simple modification allows attachment to most

5/8”–27 or 3/8”–16 threaded microphone stands and booms.

vided:

1/16 in.).

As supplied, the mount contains a locking “foot”-type slide-in

In addition to the foot-type slide-in mount, the following are pro-

•

Threaded adapter (4) to convert the swivel’s 5/8”-27 thread to a

5/16

”-18 thread.

•

Screw-type camera adapter (5) permits mounting to cameras

1/4

”-20 tapped mounting holes instead of mounting shoes.

with

•

Pistol grip adapter (6) allows the A88SM to be used with several
popular microphone pistol grips.

™ half-mount isolators and secure ca-

Model A88SM User Guide

ATTACHING TO A CAMERA

The A88SM is attached to most shoe-mount ENG cameras by
inserting the flat slide of the foot (1) in the camera’s top- or side­mount shoe and securing it with the knurled locking nut. Snap the
microphone handle into the A88SM as shown in the photo, making
certain the microphone is properly balanced. Adjust the vertical an­gle using the knob (2).

If the A88SM is to be mounted on a camera with a
mounting hole instead of a mounting shoe, insert the supplied
screw-type camera adapter (5) in the hole and secure it with the
knurled locking nut.

SECURING THE CABLE

Before attaching the microphone cable, slip a loop of it through
the slot in the A88SM and hook the loop over the protruding disc
and post (see Figure 2). Pull the loop tight against the post. Leav­ing a small amount of slack in the cable, connect it to the micro­phone. Note that the slot and post are sufficiently large to
accommodate the two-cable “Y splitter” of the Shure VP88.

ATTACHING TO A BOOM OR STAND

Remove the foot-type mount (1) from the A88SM frame by un­screwing the knob (2). Insert the swivel (3), replace the knob, and
tighten securely. Attach the swivel to any 5/8”–27 or 3/8”–16 thread
microphone boom or stand, or to any
stand using the supplied adapter (4). Use the adjustment knob to
position the A88SM in the desired direction. Insert the microphone
and secure and attach the cable as described above.

5/16”–18 thread boom or

1/4”–20 thread

MODEL A88SM MICROPHONE ISOLATION MOUNT

©2003 Shure Incorporated
27B2502 (Rev. 4)

SECURING THE CABLE

FIGURE 2

FIGURE 1

Printed in U.S.A.

PISTOL GRIP ATTACHMENT

To use the A88SM with certain popular pistol grips such as those
made by Rycote and Sennheiser, remove the foot mount (1) from
the A88SM frame by removing the knob (2) and sliding the foot
mount out of the frame. Four aluminum washers are supplied with
the A88SM. Insert the pistol grip adapter (6) with the two thin wash-
ers in the frame slot (see Figure 3), replace the knob, and tighten
it securely. Insert the pistol grip adapter in the Rycote pistol grip
frame and tighten it securely. If a Sennheiser pistol grip is to be
used, insert the pistol grip adapter in the pistol grip with both thick
aluminum washers. Then tighten the pistol grip locking screw.

PISTOL GRIP MOUNTING

FIGURE 3

SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
In U.S.A., Phone: [phone] Fax: [phone]
In Europe, Phone: [phone] Fax: [phone]
In Asia, Phone: [phone] Fax: [phone]
International Fax: [phone]