Page 1
222
HARTREY AVE EVANSTON,
ILL.
(60204)
U.S.A.
MICROPHONES AND ELECTRONIC COMPONENTS
MODEL 580SA-MP
UNIDYNE A
MODELS 580SA
AND
580SB UNIDYNE A
MODEL 580SA-MP
(see back
page)
UNIDIRECTIONAL DYNAMIC MICROPHONES
MATCHED PAIR
General:
The Model 580SA-MP is a set of two matched Unidyne A Unidirectional
Dynamic Microphones.
The units are matched within 1.0 db in level and within
1.5 db for frequency response.
For convenient connection to most tape recorders, standard phone plugs
(See
Figure D) have been installed
on
the microphone cables. All other features, specifications, and performance data listed for the Model 580SA (reverse side of data sheet)
apply to
the
Model 580SA-MP Microphones.
Application
:
The matched Model 580SA Microphones are primarily intended for
stereo .recording or similar
use.
Many acoustic conditions affect the final placement of
microphones during a stereo recording.
It is usually necessary to experiment with
various locations of the microphones to achieve placement best suited to your individual requirements. For pickup of large groups it may be advisable to raise the microphones above the performers to gain balance between front and rear of the group.
ARCHITECT’S SPECIFICATIONS
SHURE
MODEL 580SA-MP
The microphones shall be Shure Model 580SA-MP or equivalent. The microphones shall be a matched pair of Unidirectional Dynamic Microphones with a frequency range of 50 to 13,000 Hertz. The microphones shall have a “Cardioid” polar
characteristic.
The cancellation at the sides shall be approximately
6
db and the
cancellation at the rear shall be 15 to
20
db. The microphones shall have a single
high impedance input for connection into a high impedance input.
The microphone output shall be -56.5 db where
0
db = 1
volt per microbar.
The microphone rating impedance is 40,000 ohms and the Gm (sensitivity) at
1,000
Hz. shall be within 3 db of -152.5 db referenced to EIA Standard SE-105,
August, 1949.
The Model 580SA-MP Microphones shall be provided with a swivel adapter
adjustable through
90”
from vertical to horizontal. The microphones shall be equipped
with a built-in “On-Off’ switch and a
one
conductor, shielded cable, non-detachable.
The cable shall have a standard phone plug installed on the cable. The microphone
swivel adapter shall mount
on
a stand having a S’l-27 thread. The over-all dimension
of each microphone shall be
641/4”
(168.8 mm) in length and 1
l3/16”
(46.0 mm)
in diameter.
--L
T
CASE
MODEL 580SA-MP INTERNAL CONNECTIONS
U.S. Patents 3,132,713 and 3,240,883
Copyright 1965, Shure Brothers, Inc.
27A325
(9-69)
Printed
in
U.S.A.
FIGURE
D
UNIDIRECTIONAL DYNAMIC MICROPHONES
General:
The Model 580 Series Unidyne A Microphones are moving coil dynamic
units built to provide wide range reproduction of music and voice and featuring an
excellent unidirectional microphone pickup pattern. These unidirectional microphones
are ideal for quality public address, theater-stage sound systems, recording, and other
sound reinforcement applications.
The microphone features:
Exceptional true cardioid pickup pattern: symmetrical about axis and uniform
at all frequencies-providing highly effective suppression of feedback
Uniform shaped response, particularly suitable for the professional entertainer
A built-in “ON-OFF” switch with provisions for locking switch in its
“ON”
position
Versatility-for
use
in the hand or
on
a stand-for
use
indoors or outdoors
Dependability under all operating conditions
The Model 580 Microphones are supplied with an adjustable swivel adapter which
permits the microphone to be tilted through
90”
from vertical to horizontal. This
swivel, also, allows for “quick-disengage” for
use
as a hand microphone.
The Model 580SA is high impedance and may be used with any high gain
amplifier with an input impedance of
100,000
ohms or more.
The Model 580SB is low impedance and is recommended where long cable lengths
are required or under conditions of severe hum disturbance. For
use
with high impedance amplifiers, Shure Model A95A Line Matching Transformer is available for
coupling the low impedance microphone to the amplifier input.
The Model 580SA Gold features a gold finish. Specifications in other respects
are
the same as those for the Model
580SA.
Important:
Shure Microphone Cables are selected after exhaustive tests to insure
superior performance in microphones because of low capacities, superior shielding
properties and unusually long life under severe
use.
Cables with plastic insulation should not be subjected
to
excessive solderingiron heat. Carefully clean and tin the conductors and the connections to which the
conductors are to be soldered. The soldering operation can then be done with a
minimum of heat, thereby avoiding any possibility of damage to the cable.
Page 2
"I
FIGURE A
ARCHITECT'S SPECIFICATIONS
SHURE MODEL 580SB
The microphone shall be Shure Model 580SB or equivalent. The microphone
shall be a moving-coil dynamic type microphone with a shaped frequency
of
50 to
13,000 Hz. This unit shall have a "cardioid" polar characteristic. The cancellation
at the sides shall be approximately 6 db, and the cancellation at the rear shall be 15
to 20 db. The microphone has a single low impedance for connection into a 50 to
250 ohm line.
The microphone output shall be -57.0 db where
0
db = 1 milliwatt with 10
microbars.
The microphone rating impedance is 150 ohm and the Gm (Sensitivity) at 1,000
Hz.
shall be within
&
3 db of -151.0 referenced
to
EIA Standard SE-105 August
1949.
The Model 580SB shall be provided with a swivel adapter adjustable through 90"
from vertical to horizontal. The microphone is equipped with
a
built-in "ON-OFF''
switch and a two conductor, shielded cable, non-detachable. The microphone swivel
adapter will mount
on
a stand having
5/,"-27
thread. The overall dimensions shall be
641/4" (168.8 mm) in length and 113/1( (46.0 mm) in diameter.
SHURE MODEL 580SA
The microphone shall be Shure Model 580SA or equivalent. The microphone
shall be a moving-coil dynamic type microphone with a shaped frequency range
of 50 to 13,000 Hz. This unit shall have a "cardioid" polar characteristic. The
cancellation at the sides shall
be
approximately 6 db, and the cancellation at the rear
shall be 15 to 20 db. The microphone has a single high impedance for connection into
a high impedance input.
The microphone output shall be -56.5 db where
0
db 1 volt per microbar.
The microphone rating impedance is 40,000 ohms and the Gm (sensitivity) at
1,000
Hz. shall be within f 3 db of -152.5 db referenced to EIA Standard,
August 1949.
The Model 580SA shall be provided with a swivel adapter adjustable through
90" from vertical to horizontal. The microphone is equipped with a built-in "ONOFF" switch and a
one
conductor, shielded cable, non detachable. The microphone
swivel adapter will mount
on
a stand having a
5/,"-27
thread. The overall dimensions
shall be 6
4'/+"
(168.8 mm) in length and 113/1( (46.0 mm) in diameter.
ARCHITECT'S SPECIFICATIONS
NPICAL
DIRECIION*L
P&TTERN
Guarantee:
Each microphone is guaranteed to be free from electrical and mechanical defects for a period of one year from date of shipment from factory, provided
all instructions are complied with fully.
In
case of damage, return the microphone
to the factory for repairs. Our guarantee is voided
if
the microphone is subjected
to accident or abuse.
REPLACEMENT COMPONENTS
Dynamic Cartridge
........................................................................................
Model R58
Replacement Cable for Model 580SA
..........................................................
Model C60
Replacement Cable for Model 580SB
............................................................
Model C61
Please write Shure Brothers, Inc., for a complete list of the Part Replacement
Kits for Models 580SA and 580SB microphones.
SPECIFICATIONS
Type
:
Dynamic
Frequency
Response
:
50 to 13,000 Hz.
Polar
Pattern
:
Cardioid (Unidirectional) Response. Uniform with frequency,
symmetrical about the axis.
(See
Figure B)
Impedance
:
Model 580SB - 150 to 250 ohms
Model 580SA
-
High Impedance
Output Level:
1,000 Hz. Response
Model 580SB Low Impedance
Open circuit voltage
.....................
-
79.5 db (.lo5 mv)
Power level
.......................................
-
57.0 db**
EIA Microphone Rating
Gm (Sensitivity)
.........................
-151.0 db***
Model 580SA High Impedance
Open circuit voltage
...................
-
56.5 db* (1.48 mv.)
EIA Microphone Rating
Gm (Sensitivity)
...........................
-152.5 db***
*
0
db = 1 volt per microbar
EIA Standard SE-105, August 1949.
**
0
db = 1 milliwatt with 10 microbars
***
0
db
Switch
:
Built-in "ON-OFF'' switch with lockplate furnished. Microphone is shipped with lockplate installed. To lock switch in
"ON" position, put in "ON" position, loosen screw
on
lockplate
and turn lockplate 180". Retighten screw.
Positive action swivel to fit
5/,"-27
stand threads.
Swivel Adapter:
Shock Mount:
Internal vibration-isolation of rubber construction.
WPliiiL
DiRiCilONlL
PATTERN
Cable
:
Hiehlv durable with exceutionallv effective hum shielding.
Mo"dei 580SB
Y
Non-detachable 15 foot (4.6 meter)
two conductor, shielded cable
Non-detachable 15 foot (4.6 meter)
one
conductor, shielded cable
Model 580SA
Case:
Die-cast and "Armo-Dur"
Case Finish:
Dimensions
:
See Figure A
Net Weight:
Chrome and Black with stainless steel grille
1 pound
6
ounces (624 grams)
CARTRIDGE
LCODED
TERMINAL
?;CASE
/?%?NANAL
1
?WITCH
OFF"POSITION
SHOWN
IN
SHIELD
WHITE
/-----
YELLOW
BLUE
CARTRIDGE ?CASE
MODEL
580SA
INTERNAL CONNECTIONS MODEL
58OSB
INTERNAL CONNECTIONS
FIGURE C
Loading...