Shure 574SA User Guide
222 HARTREY AVE EVANSTON,
ILL.
(60204) U.S.A.
MICROPHONES AND ELECTRONIC COMPONENTS
AREA CODE 312/328-9000 CABLE SHUREMICRO
MODELS 574SA, 574SB, AND 574SF
pp
--
-
--
-
-
-
--
--
OMNIDIRECTIONAL DYNAMIC MICROPHONES
Model
574
Series
dynamic microphones. The wide
range smooth frequency response
and omnidirectional pickup
characteristics make these microphones excellent for music and
voice reproduction. The micro-
phones are ruggedly built to with-
stand rough usage and are un-
affected by temperature and humidity variations.
The versatile design of the 574
Series Microphones, coupled with
their small size and light weight,
then1 to be used in many
permit
different ways
wall or panel, on desk or floor
stand, with a lavalier or held in
the hand.
A stand adapter and lavalier cord-bracket are provided with the microphone. By
removing the cord, the lavalier bracket can be screwed onto a wall. The adapter has a
5/8
inch-27 thread which fits conventional desk stands or Roor stands. The microphone
may be easily removed from both the stand adapter or bracket for use as a hand-held
microphone.
Model 574 series have a built-in switch to control the microphone circuit. The
switch is a slide-to-talk locking type unit.
Applications:
reproduction and are ideal for recording sound on film, tape or disc; fixed or
mobile public address systems
(microphone pointing straight up), the performers may be placed all around the
microphone without changing frequency response.
Because of its high output, the high impedance Model
practically all public address amplifiers in the installations where only a moderate
length (up to 50 feet)
574SB and 574SF are designed for use in installations where long cable lengths are
required. The Model
where a medium or low impedance microphone is required.
are pressure
-
mounted on
a
MODEL 574SA MOUNTED MODEL 574SA USED AS
ON
STAND ADAPTER A LAVALIER MICROPHONE
Model 574 Series Microphones are designed for voice and music
;
call systems; and similar uses. When used vertically
574SA may be used with
(15.2m) of cable is required. Two low impedance models,
574SB unit is also ideally suited for use with transistor amplifiers
Model 574SA is a high impedance microphone. It may be used with any crystal
or ceramic microphone amplifier or other amplifier with an input impedance of
100,000 ohms or more. If additional lengths of cable are desired with the use of
Model
574SA Microphone, a high quality single conductor shielded cable is required
to extend the microphone circuit. See Figure
SWITCH SHOWN
IN
.OFF"POSITION
CARTRI DOE
POSITIVE PRESSUR
ON DIAPHRAGM
SHALL CAUSE A
POSITIVE VOLTAGE
ON PIN
ELEMENT
I
OF PLUG
574SA (HIGH IMPEDANCE)
MODEL
INTERNAL CONNECTIONS
FIGURE
Model 574SB is a low impedance microphone (150-250 ohms). This unit is
recommended for use where long cable lengths are required or under conditions of
severe hum disturbance. Model
amplifier, or into an amplifier with high impedance input. In the latter case, Shure
Model
A95A Line Matching Transformer is available for coupling the low impedance
line to the input of high impedance amplifiers.
574SF is a low-impedance microphone designed to be connected to a
Model
25 ohm line.
If additional lengths of cable are desired with the use of Model 574SB or 574SF
Microphones, a high quality two conductor shielded cable is required to extend the
microphone circuit. See Figure
574SB may be fed into standard low impedance
B
below for internal connections.
A
below for internal connections.
AMPHENOL MCLF
TYPE PLUG
1
AMPHENOL MCLM
TYPE PLUG
r
1
CABLE
ASSEMBLY
A
-
PLUG
POSITIVE PRESSURE BLACK
ON DIAPHRAGM
SHACLCAUSE
POSITIVE VOLTAGE
ON-PIN
PLUG
,NT&
A
2
OF
SWITCH SHOWN
IN
"OFF"
MODEL 57458 AND 574SF (LOW IMPEDANCE)
AMPHENOL MC2F
TYPE PLUG1
POSITION
INTERNAL CONNECTIONS
FIGURE
GROUND
B
AMPHENOL MC2M
TYPE PLUG
-
--
($*
L--
CABLE - PLUG
ASSEMBLY
SHIELD
Loading...