Shure 566 User Guide
222 HARTREY AVE.. EVANSTON. IL. 60204 U.S.A.
AREA
CODE
312/32~-9000 . CABLE:
SHUREMICRO
UNIDIRECTIONAL DYNAMIC MICROPHONE
WITH BUILT-IN VIBRATION-ISOLATION SHOCK MOUNT
General: The Model 566 Microphone is a unidirectional
dynamic microphone with a strong, built-in, wire-mesh
spherical front that contains a very effective filter designed to provide excellent protection from wind and
"pop" (explosive breath sounds). The built-in vibration-isolation shock mount prevents the pickup of
mechanical vibrations. The unit provides wide range
reproduction of music and voice -can be effectively
used outdoors and indoors.
The Unisphere I is ideal for use by professional en-
tertainers in high quality theatre-stage sound systems,
indoor or outdoor recording, cathedrals and churches,
and critical public-address systems such as those used
in political conventions and legislatures, convention
halls, hotels, public auditoriums, stadiums, etc.
The Model 566 features an exceptionally uniform
and effective unidirectional pickup pattern-provides
an easy solution to feedback problems in reverberant
locations, permits best utilization of space in small
studios, facilitates orchestral placement, and provides
practically complete exclusion of unwanted noises.
Microphone Features:
A built-in wire-mesh screen and internal filter
provides protection from wind, and "pop" (explosive breath sounds). This filter also enables
singers and speakers to perform close to the
microphone.
Unusually effective cardioid pickup pattern
eliminates feedback (annoying loudspeaker
"squeals"). In addition they prevent echoing
(boominess) that sometimes occurs in
filled halls. These microphones can also be used
closer to loudspeakers than usual, without
creating feedback problems.
Response especially effective for announcing,
narration, vocal music and combo groups.
m
Cartridge and microphone body separately shock
mounted for quiet operation.
The Model 566 is dual impedance, 50 ohms or 150
ohms, for connections into microphone inputs rated at
25 to 250 ohms.
partially-
DATA
SHEET
The microphone is recommended where long cable
lengths are required or under conditions of severe hum
disturbance. The permissible cable length is practically
unlimited, since neither response nor level is appreciably affected. For use with high impedance amplifiers,
Shure Model
able for coupling the low impedance line to the ampli-
fier input. The Shure Model
coupling a low impedance line to the high impedance
input.
Remove the impedance switch cover plate by removing the two #2-56 binding head machine screws
at each end of the cover plate. Position the switch plate
in place of the cover plate.
plate must be set into the slot of the impedance
change switch in the microphone). Replace the two
#2-56 binding head machine screws.
The center position on the switch plate
"OFF" position,
impedance of 25-50 ohms; and
phone rating impedance of 150- 250 ohms. Most appli-
cations require use of only one impedance. In this
case, insert the small #2-56
threaded hole below the impedance position NOT being
used. This prevents the switch from accidently being
turned to the wrong impedance setting during use as
"ON-OFF" switch.
Line Matching Transformer
Vibration-Isolation Stand
Desk Stand S33B
Quick Disconnect Isolation Unit A45
Cartridge
Cable
Case Assembly
Connector Assembly
Screen and Grille Assembly
On-Off Switch
Guarantee: This Shure product is guaranteed in normal
use to be free from electrical and mechanical defects
for a period of one year from the date of purchase.
Please retain proof of purchase date. This guarantee
includes all parts and labor.
Shipping Instructions: Carefully repack the unit and
return it prepaid to the factory. If outside the United
States, return the unit to your dealer or Authorized
Shure Service Center for repair. The unit will be returned to you prepaid.
A95A Line Matching Transformer is avail-
SWITCH ADAPTER INSTALLATION
"L"
position for microphone rating
OPTIONAL ACCESSORIES
...................
.....................
................................
REPLACEMENT PARTS
...................................
......................................
............................
.....................
.............................
MODEL 566
UNISPHERE
A95A transformer permits
(The key of the switch
"0"
"H"
position for micro-
fillister head screw in the
I
for the
A95A
S39A
...............
R66
C65
RK77C
RK78SM
.................
RS65
RK76S
Copyright
27A403
(LD)
1969,
Shure Brothers
Inc.
(OVER)
U.S. Patents 3,132,713, 3,240,883
Printed in U.S.A.
MODEL
566
ACHITECT'S SPECIFICATIONS
The microphone shall be Shure Model 566 or equiv-
A
alent.
quency range of 40 to 15,000
moving coil (dynamic) microphone with a fre-
Hz.,
this unit shall have
a cardioid polar characteristic. The cancellation at the
sides shall be approximately 6 db and the cancellation
at the rear shall be 15 to 20 db. The microphone shall
be equipped with a three-position impedance "Off"
switch for adjusting the microphone rating impedance
for 50 ohms and 150 ohms.
The microphone output shall be:
50 ohms, (low) impedance -57.5 db
(0 db = 1 milliwatt with 10 microbars)
150 ohms, (medium) impedance -57.5 db
(0 db = 1 milliwatt with 10 microbars)
The microphone rating Gm (sensitivity) at 1,000
Hz.
shall be within 3 db of the following levels.
Low impedance -154.5 db
Medium Impedance -154.0 db
EIA
Standard SE-105 August 1949
...................
...............
The microphone shall be provided with a swivel ad-
justable through
180.O The microphone shall be
equipped with a vibration-isolation unit in combination
with the stand connector. The microphone will mount
a
stand having %"-27 thread.
on
The overall dimensions shall be 5-9/32" (134.1 mm)
6Y2"
in height, 2-1/32 (51.5 mm) in width, and
(165.1
mm) in depth.
SPECIFICATIONS
Type:
Dynamic
Frequency Response:
40 to 15,000
Hz.
(See Figure
B)
Polar Pattern:
Cardioid (Unidirectional) pattern-Effective rejection of
sound at the rear of the microphone is uniform at all fre-
quencies, while front pickup characteristics are uniform
about the axis. (See Figure
D).
Microphone Rating Impedance:
Dual. Choice of 50 ohms "L" or 150 ohms
impedance switch for connections into microphone inputs
rated at 25 to 250 ohms. (See "switch" below. Factory set
to 150 ohms when shipped).
"H,"
selected by
Output Level:
1,000
Hz.
response.
Model 546
Open Circuit Voltage
Power Level
EIA Microphone Rating
Model 546
Open Circuit Voltage
Power Level
EIA Microphone Rating
'0 db = 1 volt per microbar.
'*O db = 1 milliwatt with 10 microbars.
***O db = EIA Standard SE-105, August 1949.
.....................................
..................................
Gm (sensitivity)
.......................................
.....................................
Gm (sensitivity)
.....................
..........................
......................
..........................
50 ohm "L" position
-
83.0 db* (.071 mv)
.-
57.5 db'*
-154.5 db***
150 ohm
-
-
-154.0 db*
"H"
76.5 db* (.I49 mv)
57.5 db**
position
**
OVER-ALL
DIMENSIONS
FIGURE
FREQUENCY IN HERTZ
FREQUENCY
,RESPONSE
FIGURE
A
B
04
Sam
,-ROTOR TERMINAL
Switch:
lmpedance selection switch with center position "OFF."
May be used with "Tamper-proof" cover, or accessory
(included) "ON-OFF" knob.
Swivel:
Positive acti:n life-time swivel permits tilting of head
through 180.
Shock Mount:
Special vibration-isolation of rubber construction.
Case:
Chrome-plated die-cast case and "Armo-Dur."
Cable:
20-foot (6.1 m) two conductor shielded with a professional
three-pin female audio connector on microphone end
designed to mate with Cannon
(Q.G.)
series Qr equivalent connector.
XL
series, Switchcraft A3
Dimensions:
See Figure A
Net Weight Less Cable:
1
Yi
pounds (567 grams)
4
CASE GROUND
POSITIVE PRESSURE PRODUCES POSITIVE
VOLTAGE
'
PIN 2 wlTn
INTERNAL
RESPECT
CONNECTIONS
FIGURE C
snlELo
WHITE
BLACK
CABLE PLUG ASSEMBLY
TO
PIN
s
FIGURE
D
Loading...