Case
Satin-chrome plated die casting with stainless steel grille
Dimensions
See Figure 2
(I-25/32 IN.) |
7.1 rnm |
(9/32 IN.) |
|
t45,2 |
|
OVERALL DIMENSIONS
FIGURE 2
Net Weight (less cable) 312 grams (11 oz)
Packaged Weight
768 grams (1 Ib 11 oz)
PHASING
To test two microphones and/or their cables for proper phasing, connect them to an amplifier and talk or sing into them while holding them three or four inches apart. The sound from the speakers should be the same when talking into either microphone or directly between them if they are in phase with each other. If the sound drops drastically, or if a dead spot is found when talking between the two microphones, they are out of phase. All cables and microphones should be tested in this manner to insure that they are in phase with each other.
To change the phase of a low-impedance microphone cable, either use a Shure A15PR Phase Reverser or interchange the BLACK and WHITE cable leads at the equipment end of the cable. To change the phase of a microphone, the microphone cartridge leads must be interchanged (see Figure 3). This should be performed by your dealer, the Shure Factory Service Department, or other qualified service personnel.
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE ON WHITE CONDUCTOR
SWIEH |
|
SHOI I N IN 'OFF'POSITION |
|
AMPHEhIOL MClM |
AMPHENOL MClF |
||||
|
|
|
|
|
|
|
- |
'lL36,, J! SHIELD |
|
|
|
|
T F O M l N A l |
|
|
|
TYDF |
D |
TYPE PLUG |
~ |
~ |
K |
~ |
~ |
L |
I |
T |
E |
;-c -7W,TE,. |
|
|
|
|
|
|
|
|
|
. ---
ASSEMBLY-
MODEL 533SA DYNAMIC MICROPHONE
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE ON WHITE CONWCTOR
SWITCH SHOWN IN 'OFF'POSITION |
AMPHENOL MC2F |
AMPHENOL MC2M |
MODEL 533SB DYNAMIC MICROPHONE
INTERNAL CONNECTIONS
FIGURE 3
ARCHITECTS'SPECIFICATIONS
The microphone shall be the Shure Model 533SA, 533SB, or equivalent. The microphone shall be a moving coil (dynamic) type with a frequency response of 40 to 11,000 Hz. The unit shall have an omnidirectional polar characteristic.
Model 533SA shall be high impedance for connection to high-impedance microphone inputs.
Model 53388 shall be low impedance with a rated impedance of 150 ohms for connection to microphone inputs rated at 19 to 300 ohms.
The microphone output shall be: |
|
533SA ........................... |
55 dB |
(0 dB = 1 volt per microbar) |
|
533SB ........................... |
56 dB |
(0 dB = 1 milliwatt per 10 microbars)
The microphone shall be provided with a swivel adapter, adjustable through 90" from vertical to horizontal, and suitable for mounting on a stand having a 543"-27 thread. The microphone shall be equipped with a built-in On-Off switch.
Model 533SA shall be provided with a detachable 4.6m (15 ft) one-conductor shielded cable with an Amphenol MClF type connector on the microphone end.
Model 533SB shall be provided with a detachable 4.6m (15 ft) two-conductor shielded cable with an Amphenol MC2M type connector on the microphone end.
The overall dimensions of the microphone shall be 168 mm (6-19/32 in.) in length and 52.4 mm (2-1116 in.) in diameter.
FURNISHED ACCESSORY
Swivel Adapter ............................. |
|
.A25B |
OPTIONAL ACCESSORIES |
|
|
Line Matching Transformer ............. . |
A95 Series |
|
Windscreen . . . . . . . . |
. . . . . . . . . . . . . . . . . . . . |
. . .A61WS |
Desk Stand . . . . . . . . |
S33B, S37A, S38B, S39A or S40A |
|
Dual Mount . . . . . . . . |
. . . . . . . . . . . . . . . . . . . . |
. . . .A26M |
Quick Disconnect Adapter ................... |
. .A45 |
|
REPLACEMENT PARTS |
|
|
|
533SA |
533sB |
|
- |
- |
Cartridge ...................... |
R33 |
R33 |
Cable ......................... |
C58 |
C57 |
Screen and Grille Assembly .....RS33 |
RS33 |
|
On-Off Switch .................. |
RK48S |
RK48S |
Cable Connector ............... |
RKI14P |
RK115P |
Plug Element .................. |
|
RK52P |
GUARANTEE
This Shure product is guaranteed in normal use to be free from electrical and mechanical defects for a period of one year from date of purchase. Please retain proof of purchase date. This guarantee includes all parts and labor. This guarantee is in lieu of any and all other guarantees or warranties, express or implied, and there shall be no recovery for any consequential or incidental damages.
SHIPPING INSTRUCTIONS
Carefully repack the unit and return it prepaid to:
Shure Brothers Incorporated Attention: Service Department 1501 West Shure Drive Arlington Heights, Illinois 60004
If outside the United States, return the unit to your dealer or Authorized Shure Service Center for repair. The unit will be returned to you prepaid.