Shure 450-II User Manual

Model 450 Series II User Guide

WIRING CONNECTIONS

Refer to Figure 1 and Table 1 below. For unbalanced opera­tion, the GREEN wire is connected to the audio input, the
WHITE wire is connected to the audio ground, and the
SHIELD is connected to chassis ground. In some cases, au­dio ground and chassis ground will be the same.

For balanced operation, the GREEN wire is connected to the
positive audio input, the WHITE wire is connected to the
negative audio input, and the SHIELD is connected to chas­sis ground.

IMPEDANCE SWITCH PRESS-TO-TALK SWITCH

GREEN

YELLOW

SHURE MODEL 450 SERIES II
PAGING AND DISPATCHING MICROPHONE

The Shure Model 450 Series II is a high output dynamic mi­crophone designed for paging and dispatching applications.
This extremely rugged microphone features an omnidirec­tional pickup pattern and a frequency response tailored for
optimum speech intelligibility. It also includes an impedance
selection switch and a locking press-to-talk switch. The
press-to-talk switch can be converted to a monitor/transmit
switch with the Shure RK199S Split-Bar Conversion Kit.

Features

• Dual impedance

• Locking press-to-talk switch

• Rugged ARMO-DURR base and case

• Adjustable height

• Optional monitor/transmit switch conversion kit

PRESS-TO-TALK SWITCH OPERATION

To operate the control bar as a press–to–talk switch, simply
hold it down and begin speaking. When you are finished
speaking, release the control bar.

To lock the control bar in the “on” position, press it down and
pull it forward. To unlock the control bar, push it back and re­lease it.

IMPEDANCE SELECTION

To select high or low impedance, move the impedance selec­tion switch, located under the mic rophone base, to either the
HIGH or LO position. The switch is factory pre–set to LO.

Shure recommends the low impedance setting if long
lengths of cable are used, or if severe hum is encountered.
Use Shure A95 Line Matching Transformers to match a low
impedance (300 Ω) microphone line to a high impedance
amplifier input.

BLACK

12 3

BLACK
RED
GREEN
WHITE

SHIELD

ORANGE

RED

HILO

GREEN

WHITE

WIRING DIAGRAM

FIGURE 1

Table 1. Typical Cable-to-Connector Wiring

INPUT TYPE WIRE

UNBALANCED WHIT E AUDIO GROUND PIN 3 SLEEVE

BALANCED WHITE AUDI O – PIN 3 RING

COLOR

GREEN AUDIO PIN 2 TIP

SHIELD CHASSIS GROUND PIN 1 SLEEVE
GREEN AUDIO + PIN 2 TIP

SHIELD CHASSIS GROUND PIN 1 SLEEVE

FUNCTION XLR

CONNECTOR

1/4 IN.

PHONE JACK

NOTE: The RED and BLACK leads are not part of the audio

circuit. These w ires p rovide a c ontact cl osure w hen t he p ress­to-talk switch is depressed. This closure m ay b e u sed t o c on­trol an external relay or a transmit/receive circuit.

CHANGING PTT CIRCUIT TO NORMALLY OPEN

Using microphones in parallel requires a normally open mi­crophone circuit. To modify the press–to–talk switch so that
it provides a normally open circuit, proceed as follows:

1. Remove the screws, washers, and bottom plate from
the microphone.

2. Unsolder the black, red, and white leads from the terminal
of the press–to–talk switch (see Figure 1). Make
sure these leads are still soldered together . If necessary,
resolder them and insulate the connection.

3. Replace the bottom plate and secure it with the screws
and washers removed in Step 1.

2005, Shure Incorporated
27C2917 (Rev. 3)

Printed in U.S.A.

TRANSMIT/MONITOR SWITCH CONVERSION KIT

When the optional split-bar Transmit/Monitor Switch Conver­sion Kit is installed, the Monitor bar must be d epressed before
the Transmit switch can be d epressed, requiring the o perator
to verify that the channel is open before transmitting. The
Monitor bar can be locked in the “on” position. The Transmit
bar is momentary and cannot be locked.

NOTE: Transceiver wiring i nformation must b e obtained f rom
the transceiver schematic and/or the manufacturer.

SPECIFICATIONS
Type

Dynamic

Frequency Response

200 to 5,000 Hz (see Figure 2)

TYPICAL FREQUENCY RESPONSE

FIGURE 2

Polar Pattern

Omnidirectional

Impedance (at 1,000 Hz)

High Impedance: 30,000 Ω
Low Impedance: 225 Ω

Recommended Load Impedance

High Impedance: 100,000 Ω
Low Impedance: 1,000 Ω

Output Level (at 1,000 Hz, Open Circuit Voltage)

High Impedance Low Impedance

–35.0 dBV/Pa* –57.0 dBV/Pa*

(17.8 mV) (1.4 mV)

*1 Pa = 94 dB SPL

Switches

Locking Press-to-Talk Switch: Activates microphone cir­cuit and an external relay or control circuit. The micro­phone circuit is normally shorted.

Impedance Selection Switch: Double-pole, double-throw
slide switch located in the base of the microphone.

Cable

2.1 m (7 ft.) four-conductor, two conductors shielded,
non-detachable

Case

Two-tone gray ARMO-DUR

R

OVERALL DIMENSIONS

FIGURE 3

Net Weight

737 grams (1 lb., 10 oz.)

Shipping Weight

1020 grams (2 lb., 4 oz.)

Certification

Conforms to European Union directives, eligible to bear
CE marking; meets European Union EMC Immunity Re­quirements (EN 50082–1, 1992).

REPLACEMENT PARTS

Cartridge R96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cable C31C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

On/Off Switch RK141S. . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONAL ACCESSORIES

Transmit/Monitor Split-Bar Switch Kit RK199S. . . . . . . .

SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Intl Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]