SHOWTEC V1 User Manual
LED Lightbar 12 Pixel V1
Highlit e Int ernati onal B. V. – Vest ast raat 2 – 6468 EX – Kerkrade – the Net herlands
Ordercode: 42197
MANUAL
ENGLISH
Ordercode: 42197
LED Lightbar 12 Pixel
Table of contents
Warning .......................................................................................................................................................... 2
Safety Instru ctions....................................................................................................................................... 2
Operating Determinations ......................................................................................................................... 4
Rigging ....................................................................................................................................................... 4
Connection with the mains ........................................................................................................................ 5
Return Procedure ....................................................................................................................................... 5
Claims......................................................................................................................................................... 5
Descripti on of the device ............................................................................................................................... 6
Optional accessories.................................................................................................................................. 6
Overview .................................................................................................................................................... 7
Installation ...................................................................................................................................................... 7
Set Up and Operation..................................................................................................................................... 7
Control Modes............................................................................................................................................ 7
One LED Lightbar 12 Pixel ( Built -in programs, Auto Run)......................................................................... 7
One LED Lightbar 12 Pixel (Sound-control) .............................................................................................. 7
One LED Lightbar 12 Pixel (Manual control) ............................................................................................ 8
Multiple LED Lightbars 12 Pixel (Master/Slave control)............................................................................. 8
Multiple LED Lightbars 12 Pixel (DMX512 Mode) ...................................................................................... 9
Fixture Linking ........................................................................................................................................... 10
Data Cabling ........................................................................................................................................... 10
Control Panel ........................................................................................................................................... 11
DMX Control Mode .................................................................................................................................. 11
DMX Addressing ....................................................................................................................................... 11
Menu overview............................................................................................................................................. 12
Main Menu Options .................................................................................................................................. 13
Built-in Programs .................................................................................................................................... 13
Auto Run Program ................................................................................................................................. 14
DMX Mode ............................................................................................................................................ 14
Master / slave addressing ...................................................................................................................... 15
Sound control Mode.............................................................................................................................. 15
Static Color Mode ................................................................................................................................. 16
Settings .................................................................................................................................................. 16
Reset factory settings ............................................................................................................................ 16
DMX Channels .......................................................................................................................................... 17
4 DMX Chann els .................................................................................................................................... 17
4 DMX Chann els .................................................................................................................................... 17
6 DMX Chann els .................................................................................................................................... 18
12 DMX Channels .................................................................................................................................. 18
10 DMX Channels .................................................................................................................................. 20
18 DMX Channels .................................................................................................................................. 21
48 DMX Channels .................................................................................................................................. 24
Mai ntenance ................................................................................................................................................ 26
Replacing a Fuse...................................................................................................................................... 26
Troubleshooting ............................................................................................................................................ 26
No Light .................................................................................................................................................... 26
No Response to DMX................................................................................................................................ 26
Product Specifications.................................................................................................................................. 28
Dimensions ................................................................................................................................................... 29
Notes ............................................................................................................................................................ 30
1
Ordercode: 42197
LED Lightbar 12 Pixel
Your shipment includes:
Showtec LED Lightbar 12 Pixel
• 2 brackets and screws
• IEC pow ercable 1,5m
• User manual
Warning
Unpacking Instructions
Imm ediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer imm ediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself show s signs of mishandling. Save the carton and all packin g materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit hi gher operating temperatures than in ideal or singular
optimum conditions. For this reason w hen all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If im proving the lifespan is of higher priority, place care in providing for low er
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involv ed with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and w arning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
2
Ordercode: 42197
LED Lightbar 12 Pixel
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non -observance of
this manual or any unauthorized m odification to the device.
Never let the power cord come into contact with other cables! Handle the pow er cord and all
connections with the mains with particular caution!
Never remove w arning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as t his would reduce the device’s lifespan.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after hav ing checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed w hile operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the pow er cord.
Make sure that the device is not exposed to extreme heat, m oisture or dust.
Make sure that the available voltage is not higher than stated on the rear p anel.
Make sure that the pow er cord is never crimped or damaged. Check the device and the pow er
cord from time to time.
If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
If device w as dropped or struck, disconnect mains pow er supply immediately. Hav e a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on imm ediately. The arising condensation w ater might damage your device. Leave the
device switched off until it has reached room temperature.
If your Show tec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Show tec dealer for service.
For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement, use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the LED Lightbar 12 Pixel. The
manufacturer w ill not accept liability for damages caused by the misuse or incorrect installation of
this device.
This device falls under protection class I. Therefore it is essential to connect the yellow /green
conductor to earth.
During the initial start -up, some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
Repairs, servicing and electrical connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
3
Ordercode: 42197
LED Lightbar 12 Pixel
Operating Determinations
● This device is not designed for permanent operation. Regular operation breaks will ensure that the
device w ill serve you for a long time without defects.
● The minimum distance betw een light -output and the illuminated surface must be bigger than 1
meter.
● The maximum ambient temperature ta = 40°C must never be exceeded.
● The relative hum idity must not exceed 50 % w ith an ambient temperature of 40° C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the w arranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow t he European and nat ional guidelines concerning rigging, trussing and all
ot her safety issues.
Do not attempt t he inst allation yourself!
Always let the inst allation be carried out by an aut horized dealer!
Procedure:
If the LED Lightbar 12 Pixel is low ered from the ceiling or high joists, professional trussing systems
have to be used.
Use a clamp to mount the LED Lightbar 12 Pixel, w ith the mounting-bracket, to the trussing system.
The LED Lightbar 12 Pixel must never be fixed sw inging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net
or safety-cable.
When rigging, derigging or servicing the LED Lightbar 12 Pixel, alw ays make sure, that the area
below the installation place is blocked and staying in the area is forbidden.
The LED Lightbar 12 Pixel can be placed on a flat stage floor or mounted to any kind of truss by a clam p.
4
Ordercode: 42197
LED Lightbar 12 Pixel
Internati onal
EU Cable
UK Cabl e
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Return Procedure
Connection with the mains
Connect the device to the mains w ith the pow er plug.
Always check if the right color cable is connected to the right place.
Make sure t hat the device is always connect ed properly t o t he earth!
Improper inst allation can cause serious damage t o people and property!
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package m ust be clearly labeled with a Return Authorization Number (RMA num ber). Products returned
without an RMA num ber w ill be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or m ail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is alw ays a safe method to use.
Note: If you ar e given an RMA number, please include the foll owing information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone num ber.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage m ust be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and subm it claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the deliv ery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments w ill be refused, unless
agreed otherwise in writing.
Com plaints against us must be made known in writing or by fax w ithin 10 w orking days after receipt of the
invoice. After this period, com plaints will not be handled anymore.
Com plaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of w hich the obligation is resulting.
5
Ordercode: 42197
LED Lightbar 12 Pixel
Description of the device
Features
The Show tec LED Lightbar 12 Pixel is a cost effective LED bar w ith 12 x 4-in-1 RGBW LEDs. It offers full pixel
control in 48 channel mode to create beautiful color flows but can also be controlled in 4, 6, 10, 12 or 18
channel mode. With the RGBW LEDs it is possible to create both saturated and pastel colors.
• LEDs: 12 x 4W RGBW
• Beam angle: 30 º
• Com pact size
• Pixel control
• Pow er and data daisy chain
• Lumen @2m: 500 (Full On)
• Colormixing: RGBW
• Pow er Supply: 100-240V AC, 50/60Hz
• Drive current: 100 mA
• Refresh rate: 2 KHz
• Control Mode: DMX512
• Dimmer: 0-100%
• Strobe: 0-20Hz
• Pow er Consumption: 20 Watt
• 3 pin female XLR socket and 3 pin male XLR socket
• IEC Pow er In and IEC pow er Out (Max. 10A)
• Linkable via 3-pin XLR cable
• Built-in microphone
• Housing: aluminum
• LED display
• Fuse: T1L / 250V
• Cooling: aluminum heatsink
• IP rating: IP-20
• Built-in program s mode, Auto running mode, DMX mode, slave mode, static color mode and sound-
activated mode.
• Selectable 4, 4, 6, 10, 12, 18 and 48 DMX channel operation
• Dimensions: 1080 x 65 x 88 mm (LXWXH) (incl. brackets)
• Weight: 2,14 kg
Note: Know ledge of DMX is required to fully utilize this unit.
Optional accessories
D7012 Case for 4x LED Bar Value Line
D7595 LED Bar Case
6
Ordercode: 42197
LED Lightbar 12 Pixel
Fig. 01
There are 6 modes:
Built-in Programs
Auto Run
Sound-controlled
Manual control (Static)
Master/Slave
DMX512
Overview
01) IEC Pow er In
02) Ground/Earth connection
03) Fuse T1L / 250V
04) 12 x 4W RGBW
05) Menu Buttons + LED display
06) DMX signal connector (IN) 3-pin
07) DMX signal connector (OUT) 3-pin
08) IEC Pow er Out (m ax 10A)
09) Adjustment screw + mounting bracket for Truss mounting
Installation
Remove all packing materials from the LED Lightbar 12 Pixel.
Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properl y.
Always disconnect from electric mains power supply before cleani ng or servicing.
Damages caused by non-observance are not subject to war ranty.
Set Up and Operation
Follow the directions below , as they pertain to your preferred operation mode.
Before plugging the unit in, alw ays make sure that the pow er supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main pow er supply.
Control Modes
One LED Lightbar 12 Pixel ( Bui lt-in programs, Auto Run)
01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides
for air circulation.
02) When the LED Lightbar is not connected by a DMX-cable, it functions as a stand-alone device.
03) If device is set to or , then the fixture w ill play one of its built -in programs or show its
auto run mode. Please see pages 13-14 for more information about the built-in programs or auto run
mode.
One LED Lightbar 12 Pixel (Sound-control)
01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides
for air circulation.
02) When the LED Lightbar is not connected by a DMX-cable, it functions as a stand-alone device.
03) Turn on the music. If device is set to (Audio), then the fixture w ill react to the beat of the
music. Please see page 15 for more information about the Sound-controlled mode.
7
Ordercode: 42197
LED Lightbar 12 Pixel
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
Fig. 02
One LED Lightbar 12 Pixel (Manual control)
01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides
for air circulation.
02) When the LED Lightbar is not connected by a DMX-cable, it functions as a stand-alone device.
03) If device is set to , then the fixture can be manually controlled.
04) Please see page 16 for more information about the Manual control mode.
Multipl e LED Lightbars 12 Pixel (Master/Slave control)
01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides
for air circulation.
02) Plug the end of the electric mains power cord into a proper electric pow er supply socket.
03) Use a 3-p XLR cable to connect the LED Lightbars and other devices.
04) Link the units as shown in Fig. 02, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units. You can use the
same functions on the master device as described on pages 13-14 (Built-in Programs, Auto run). This
means you can set your desired operation mode on the master device and all slave devices will
react the same as the master device.
Multipl e LED Lightbars 12 Pixel (Master/Slave control)
8
Ordercode: 42197
LED Lightbar 12 Pixel
Fig. 03
Multipl e LED Lightbars 12 Pixel (DMX512 Mode)
01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 m eter on all sides
for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Use a 3-p XLR cable to connect the LED Lightbars and other devices.
04) Link the units as shown in Fig. 03, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units.
05) Supply electric power: Plug electric mains pow er cords into each unit's IEC socket, then plug the
other end of the mains pow er cord into proper electric power supply sockets, starting with the first
unit. Do not supply pow er before the w hole system is set up and connected properly.
Multipl e LED Lightbars 12 Pixel DMX Set Up
9
Note: Li nk all cables before connecting electri c power!
Loading...