SHOWTEC Titan Strobe blaze User Manual
Titan Strobe BLAZE V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
ENGLISH
Ordercode: 40297
MANUAL
1
Ordercode: 40297
Titan Strobe BLAZE
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Rigging ............................................................................................................................................................................ 4
Connection with the mains......................................................................................................................................... 5
Return Procedure .......................................................................................................................................................... 5
Claims .............................................................................................................................................................................. 5
Description of the device ................................................................................................................................................. 6
Features .......................................................................................................................................................................... 6
Frontside.......................................................................................................................................................................... 6
Backside ......................................................................................................................................................................... 7
Installation ........................................................................................................................................................................... 7
Installing the Lamp ........................................................................................................................................................ 7
Set Up and Operation ....................................................................................................................................................... 7
Control Modes ............................................................................................................................................................... 8
One Titan Strobe (Manual) ...................................................................................................................................... 8
Multiple Titan Strobes (Master/Slave control) ....................................................................................................... 8
Multiple Titan Strobes (DMX Control) ..................................................................................................................... 9
Fixture Linking ...............................................................................................................................................................10
Data Cabling ...............................................................................................................................................................10
Control Panel ...............................................................................................................................................................11
Control Mode ..............................................................................................................................................................11
DMX Addressing ..........................................................................................................................................................11
Menu Overview ...........................................................................................................................................................12
Main Menu Options ....................................................................................................................................................13
1. Operation Modes ................................................................................................................................................13
2. DMX Address (DMX Settings) .............................................................................................................................13
3. Channel Modes (DMX Settings) ........................................................................................................................13
4. DMX Error (DMX Settings) ...................................................................................................................................14
5. Strobe Brightness (Manual Mode) ....................................................................................................................14
6. Strobe Frequency (Manual Mode) ..................................................................................................................14
7. LED Master Dimmer (Manual Mode) ...............................................................................................................14
8. LED Color Macros (Manual Mode) ..................................................................................................................14
9. LED Color Switch/Flow Speed (Manual Mode) .............................................................................................14
10. LED Color Switch/Color Flow Settings (Manual Mode) ..............................................................................15
11. LED Strobe Frequency (Manual Mode) ........................................................................................................15
DMX Channels .............................................................................................................................................................15
3 Channels ................................................................................................................................................................15
5 Channels ................................................................................................................................................................16
9 Channels ................................................................................................................................................................17
Maintenance ....................................................................................................................................................................18
Changing the Lamp ...................................................................................................................................................18
Replacing the Fuse .....................................................................................................................................................18
Troubleshooting ...............................................................................................................................................................18
No Light .........................................................................................................................................................................18
No Response to DMX..................................................................................................................................................19
Product Specifications ....................................................................................................................................................20
Dimensions ........................................................................................................................................................................21
2
Ordercode: 40297
Titan Strobe BLAZE
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Titan Strobe BLAZE
Pro power cable (1,5 m)
Mounting bracket
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
3
Ordercode: 40297
Titan Strobe BLAZE
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never run the device without lamp!
• Never ignite the lamp if the objective lens or any housing cover is open, as discharge lamps may
expose and emit a high ultraviolet radiation, which may cause burns.
• Never look directly into the light source.
• Never leave any cables lying around.
• Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
• Never strain the cable insert or the female part in the device. There must always be sufficient cable
going to the device. Otherwise, the cable will be damaged, which can cause serious damage.
• Never operate the stroboscope without protective shield! When the shield is cracked, replace it
before using the device again.
• Do not insert objects into air vents.
• Do not connect this device to a dimmer pack.
• Do not switch the device on and off in short intervals, as this would reduce the lamp’s life.
• Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
• Do not shake the device. Avoid brute force when installing or operating the device.
• Only use device indoors, avoid contact with water or other liquids.
• Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always replace the lamp, when it is damaged or deformed due to the heat.
• Always keep case closed while operating.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Always disconnect power from the mains, when device is not used, before cleaning or when
replacing lamp! Only handle the power cord by the plug. Never pull out the plug by tugging the
power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
• Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
• If device is dropped or struck, disconnect main power supply immediately. Have a qualified
engineer inspect for safety before operating.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
• If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. The fixture must be installed out of the reach of children. Never leave the unit
running unattended.
• For replacement use lamps of same type and rating only.
• Allow time to cool down, before replacing lamp.
• Keep away from direct insulation.
• This device is only allowed for an installation via the mounting bracket.
• The user is responsible for correct positioning and operating of the Titan Strobe. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
• The relative humidity must not exceed 50% with an ambient temperature of 35°C.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
4
Ordercode: 40297
Titan Strobe BLAZE
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
• To eliminate wear and improve lifespan, during periods of non-use, completely disconnect from
power via breaker or by unplugging.
• The maximum ambient temperature t
a
= 35°C must never be exceeded.
• The relative humidity must not exceed 50 % with an ambient temperature of 35°C.
• If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
• If the Titan Strobe is lowered from the ceiling or high joists, professional trussing systems have to be
used.
• Use a clamp to mount the Titan Strobe, with the mounting bracket, to the trussing system.
• The Titan Strobe must never be fixed swinging freely in the room.
• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
• When rigging, derigging or servicing the Titan Strobe, always make sure that the area below the
installation site is secured and that there are not any unauthorized people around.
The Titan Strobe BLAZE can be mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
5
Ordercode: 40297
Titan Strobe BLAZE
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.
6
Ordercode: 40297
Titan Strobe BLAZE
Description of the device
Features
The Showtec Titan Strobe BLAZE is a perfect enhancement of the traditional Titan Strobe.
The RGB LEDs provide a colorful illumination of the reflector. The pre-programmed color macros are
divided into zones, in order to create color flows. The built-in lightning simulation, linear and random
strobe effects, blinder and single flash mode make the new Titan Strobe BLAZE the complete package for
all professional lighting operators.
• Input voltage: 240V AC, 50/60Hz
• Power consumption: 1800W
• Light source (strobe): Xenon 1500W tube
• Light source (blaze): 2 x RGB LED strip
• Light output: 120,000 lm
• Strobe (linear): 1-15Hz
• Strobe (blinder): 25Hz
• Control: Manual, Master/Slave, DMX-512/RDM
• DMX control: via standard DMX controller
• DMX channels: 3, 5, 9 channels
• Circuit breaker: 16A
• Color: Black
• Housing: Metal & flame-retardant plastic
• Connections: 3-pin/5-pin XLR IN/OUT, Pro power connector Blue IN
• IP rating: IP-20
• Dimensions: 495 x 160 x 265 mm (LxWxH)
• Weight: 5,9 kg
Frontside
Fig. 01
01) Mounting bracket with inclination screw
02) Adjustment screw
03) Lens
7
Ordercode: 40297
Titan Strobe BLAZE
Backside
Fig. 02
04) 16A circuit breaker (power switch ON/OFF)
05) 240V Pro power connector Blue IN
06) LCD display + LED indicators and control buttons
07) 3-pin DMX signal connector OUT
08) 3-pin DMX signal connector IN
09) Cooling fan
10) 5-pin DMX signal connector OUT
11) 5-pin DMX signal connector IN
Installation
Remove all packing materials from the Titan Strobe BLAZE. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Installing the Lamp
The Showtec Titan Strobe BLAZE uses the Showtec PX-1500 Xenon flashtube lamp, 1500W (ordercode
82690). Use only the appropriate lamp for your unit. Note that product versions, that use other lamps, may
be offered in the future. Check your product specification label for information.
Always disconnect from electric mains power supply before changing lamps.
The lamp has to be replaced when it is damaged or deformed due to the heat.
Do not install lamps of higher wattage! Lamps of higher wattage generate temperatures which the
device was not designed for.
Damages caused by non-observance are not subject to warranty.
DANGEROUS: Leave the device disconnected for 15 minutes, before opening.
Otherwise, you risk electrocution.
01) Disconnect from main power supply, and leave for 15 minutes.
02) Remove the glass cover. With the left hand, gently pull the lamp out of the spring, while pushing the
spring back with the right hand.
03) Remove the lamp. Read lamp instructions. Do not touch the lamp bulb glass. Oil on hands shortens
the lamp life. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing
alcohol.) Hold the lamp with one hand and insert the lamp into the spring. Put the glass cover back.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Loading...