Sunraise LED V2
Highlite Interna t ional B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 43078
MANUAL
ENGLISH
Ordercode: 43078
Sunraise LED
Table of contents
Warning ............................................................................................................................................................................... 2
Safety Instructions ......................................................................................................................................................... 2
Operating Determinations .......................................................................................................................................... 4
Rigging ............................................................................................................................................................................ 4
Connection with the mains......................................................................................................................................... 4
Return Procedure .......................................................................................................................................................... 5
Claims .............................................................................................................................................................................. 5
Description of the device ................................................................................................................................................. 6
Features .......................................................................................................................................................................... 6
Overview ........................................................................................................................................................................ 6
Installation ........................................................................................................................................................................... 6
Set Up and Operation ....................................................................................................................................................... 7
Control Modes ............................................................................................................................................................... 7
One Sunraise LED (Built-in programs, Auto, Static Colors) ................................................................................. 7
One Sunraise LED (Sound-controlled) .................................................................................................................... 7
Multiple Sunraise LEDs (Master/Slave control) ...................................................................................................... 7
Multiple Sunraise LEDs (DMX Control) .................................................................................................................... 8
Fixture Linking ................................................................................................................................................................. 9
Data Cabling ................................................................................................................................................................. 9
Control Panel ...............................................................................................................................................................10
Control Mode ..............................................................................................................................................................10
DMX Addressing ..........................................................................................................................................................10
Menu Overview ...........................................................................................................................................................11
Main Menu Options ....................................................................................................................................................12
1. Built-in Programs ...................................................................................................................................................12
2. Auto ........................................................................................................................................................................12
3. DMX Mode ............................................................................................................................................................12
4. Slave Mode ...........................................................................................................................................................12
5. Sound control mode ...........................................................................................................................................12
6. Static Color Mode ...............................................................................................................................................13
DMX Channels .............................................................................................................................................................14
4 channels .................................................................................................................................................................14
Maintenance ....................................................................................................................................................................15
Replacing the Fuse .....................................................................................................................................................15
Troubleshooting ...............................................................................................................................................................15
No Light .........................................................................................................................................................................15
No Response to DMX..................................................................................................................................................16
Product Specifications ....................................................................................................................................................17
Dimensions ........................................................................................................................................................................18
1
Ordercode: 43078
Sunraise LED
Your shipment includes:
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
• Showtec Sunraise LED
• IEC power cable (1,5 m)
• User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
• be qualified
• follow the instructions of this manual
2
Ordercode: 43078
Sunraise LED
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the device and do not modify the device.
• Never use anything to cover the ground contact.
• Never look directly into the light source.
• Never leave any cables lying around.
• Do not insert objects into air vents.
• Do not connect this device to a dimmerpack.
• Do not switch the device on and off in short intervals, as this would reduce the device’s life.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Never use the device during thunderstorms, unplug the device immediately.
• Only use device indoors, avoid contact with water or other liquids.
• Do not touch the device’s housing bare-handed during its operation (housing becomes hot).
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always keep case closed while operating.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Only install the device with the hanging bracket.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
• If the external cable is damaged, it has to be replaced by a qualified technician.
• If the lens or glass is obvi o usly damaged, it has to be replaced. So that its functions are not impaired,
due to cracks or deep scratches.
• If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
• If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. The fixture must be installed out of the reach of children. Never leave the unit
running unattended.
• For replacement use fuses of same type and rating only.
• Allow time to cool down, before replacing lamp.
• The user is responsible for correct positioning and operating of the Sunraise LED. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
3
Ordercode: 43078
Sunraise LED
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
• WARRANTY: Till one year after date of purchase.
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
• The maximum ambient temperature t
• The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
• If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
= 40°C must never be exceeded.
a
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
• If the LED effect is lowered from the ceiling or high joists, professional trussing systems have to be
used.
• Use a clamp to mount the projector, with the mounting bracket, to the trussing system.
• The projector must never be fixed swinging freely in the room.
• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
• When rigging, derigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
4
Ordercode: 43078
Sunraise LED
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
and request an RMA prior to shipping the fixture.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.
5
Ordercode: 43078
Sunraise LED
Overview
Fig. 01
01) 55 x 3W RGBWA LEDs
04) 3-pin DMX signal connector IN
05) Ground/earth connection
07) 100-240V IEC power connector + Fuse 1A/250V
Description of the device
Features
The Showtec Sunraise LED is a light fixture with high output and great effects.
• Light source: 55 x 3W RGBWA LEDs
• Lumens: 1000 for each color
• Lux @ 2 m: 475
• Power supply: 100-240V AC, 50/60 Hz
• Power consumption: 35W
• DMX channels: 4
• Control: Built-in programs, Auto, Static Colors, Sound-controlled, Master/Slave, DMX512
• DMX control
• Very wide beam spread
• Great effect for clubs, DJs and party rooms
• Maximum distance: 20 m
• Dimmer: 100%
• Strobe: 0-12Hz
• Rotation speed: 8 RPM
• Housing: Iron
• Color: Black
• Plug & Play
• Connections: 3-pin DMX IN/OUT
• Fuse: F1A/250V
• Dimensions: 266 x 266 x 260 mm (LxWxH)
• Weight: 2,8 kg
02) Safety eye
03) LED display + menu buttons
Installation
Remove all packing materials from the Sunraise LED. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
6
06) 3-pin DMX signal connector OUT
Ordercode: 43078
Sunraise LED
There are 6 modes:
• Built-in programs
• Auto run
• Static Color
• Sound-controlled
• Master/Slave
• DMX-512 (4CH)
The pins:
01) Earth
Multiple Sunraise LEDs (Master/Slave control)
Fig. 02
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Control Modes
One Sunraise LED (Built-in programs, Auto, Static Colors)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Sunraise LED is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 12-13 for more information about the Built-in programs, Auto Run and Static Color.
One Sunraise LED (Sound-controlled)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Turn on the music. If the device is set to sound-control, then the Sunraise LED will react to the beat of
the music. Please see page 12 for more information about the sound-control options.
Multiple Sunraise LEDs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Use a 3-pin XLR cable to connect the Sunraise LED.
02) Signal -
03) Signal +
03) Link the units as shown in fig. 02. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX cable. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on pages 12-13 (Built-in
programs, Auto run, Static Color, Sound-controlled). This means that you can set your desired
operation mode on the master device and all slave devices will react the same as the master
device.
7
Ordercode: 43078
Sunraise LED
Multiple Sunraise LEDs DMX Set Up
Fig. 03
Multiple Sunraise LEDs (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Sunraise LEDs and other devices.
04) Link the units as shown in fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
8
Note : Link all cables before connectin g el ectr ic power
Ordercode: 43078
Sunraise LED
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a power link @ 230V: 50 fixtures
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link @ 110V: 25 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Au di o X -type data cable XLR/M 3-pin > X LR /F 3-pin. Ordercode FLX0175 (0,75 m ),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m), FL09150 (1,5
m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
9
Ordercode: 43078
Sunraise LED
Control Panel
A) LED display
B) MODE button
C) SETUP button
D) UP button
E) DOWN button
Fig. 04
The Sunraise LED can be operated with a controller in control mode or without the controller in
stand-alone mode.
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign DMX fixture addresses, which is the first
channel with which the Sunraise LED will respond to the controller.
Please note, when you use the controller, the unit has 4 channels.
When using multiple Sunraise LEDs, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Sunraise LED should be 1(001); the DMX address of the second
Sunraise LED should be 1+4=5 (005); the DMX address of the third Sunraise LED should be 5+4=9 (009), etc.
Please, be sure that you do not have any overlapping channels in order to control each Sunraise LED
correctly. If two or more Sunraise LEDs are addressed similarly, they will work similarly.
Controlling:
After having addressed all Sunraise LED fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Sunraise LED will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the “LED“ on the control panel will not flash.
If not, the problem may be:
• The XLR cable from the controller is not connected with the input of the Sunraise LED.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
10
Ordercode: 43078
Sunraise LED
Menu Overview
11
Ordercode: 43078
Sunraise LED
Main Menu Options
Built-in programs
Auto
DMX mode
Master/Slave mode
Sound-controlled mode
Static colors
1. Built-in Programs
01) Press the MODE button until the display shows .
02) With this menu you can set the built-in programs.
03) Press the UP/DOWN buttons to choose one of the 14 built-in programs .
2. Auto
01) Press the MODE button until the display shows .
02) The Sunraise LED will now play all 14 built-in programs in a sequence.
3. DMX Mode
With this menu you can set the DMX address.
01) Press the MODE button until the display shows .
02) You can choose one of the 512 different DMX addresses.
03) Press the UP/DOWN buttons to select the required address. The adjustment range is between
.
04) Press the SETUP button to see the current DMX mode. The display will show (4 channels).
4. Slave Mode
01) When the display shows then the Sunraise LED is operating as a slave device. It will now
react the same as the master device.
5. Sound control mode
01) Press the MODE button until the display shows .
02) The Sunraise LED will now react to the beat of the background music.
03) Press the SETUP button to enter sound sensitivity settings.
04) Press the UP/DOWN buttons to set the desired sound sensitivity. The adjustment range is between
12
, from OFF to high sensitivity.
Ordercode: 43078
Sunraise LED
6. Static Color Mode
01) Press the MODE button until the display shows .
02) Press the UP/DOWN buttons to select one of the 19 different static color effects.
13
Ordercode: 43078
Sunraise LED
Channel 1 – Programs
0-9
Blackout
10-19
Red
20-29
Green
30-39
Blue
40-49
White
50-59
Amber
60-69
Red + Green
70-79
Red + Blue
80-89
Red + White
90-99
Red + Amber
100-109
Green + Blue
110-119
Green + White
120-129
Green + Amber
130-139
Blue + White
140-149
Blue + Amber
150-159
White + Amber
160-169
Red + Green + Blue
170-179
Red + Green + Blue + White
180-189
Red + Green + Blue + Amber
190-199
Red + Green + Blue + White + Amber
200-229
Auto
230-255
Sound-controlled mode
Channel 2 – Strobe
0-9
Not functional
10-255
Strobe effect (0-12Hz), from low to high frequency
Channel 3 – Auto Speed CH1 must be set between 200-229
0-9
Not functional
10-255
Speed adjustment, from slow to fast
Channel 4 – Motor rotation
0-9
OFF
10-119
Clockwise rotation, from slow to fast
120-129
Stop
130-255
Counterclockwise rotation, from slow to fast
DMX Channels
4 channels
14
Ordercode: 43078
Sunraise LED
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Sunraise LED requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the lightoutput very quickly.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Gently pry up the fuse cover. The fuse
will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Sunraise LED to your Showtec dealer.
03) The fuse. Replace the fuse. See page 15 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Sunraise LED , as this may
damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
15
Ordercode: 43078
Sunraise LED
Problem
Probable cause(s)
Solution
• Check if power is switched on and
Primary fuse blown
• Replace fuse
Fixtures reset
controller
The controller is not connected.
• Connect controller.
• Install a phase reversing cable
• Check data quality. If much lower
disturbing the link
• Inspect connections and cables.
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
• Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
• Check address setting
• Bypass one fixture at a time until
serviced by a qualified technician
• Install a phase-reversing cable
erratically
• Allow the fixture to cool down
• Turn up the air conditioning
• Disconnect the fixture and return it
to your dealer
The power supply settings do not
frequency
• Disconnect fixture. Check settings
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
One or more
fixtures do not
function at all
correctly, but all
respond
erratically or not
at all to the
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
No light or LEDs
cut out
intermittently
No power to the fixture
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
Poor data quality
Bad data link connection
One of the fixtures is defective and
disturbs data transmission on the
link
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
Fixture is too hot
LEDs damaged
cables are plugged in
between the controller and the
first fixture on the link
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
Correct poor connections. Repair
normal operation is restored:
unplug both connectors and
connect them directly together.
• Have the defective fixture
between the fixtures or swap pin 2
and 3 in the fixture that behaves
• Clean the fan
• Make sure that air vents are not
blocked
match local AC voltage and
16
and correct if necessary
Ordercode: 43078
Sunraise LED
Model:
Showtec Sunraise LED
Input voltage:
100-240V AC, 50/60Hz
Power consumption:
35W
DMX linking:
30pcs
Fuse:
F1A/250V
Dimensions:
266 x 266 x 260 mm (LxWxH)
Weight:
2,8 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
4 channels
Signal input:
3-pin XLR IN
Signal output:
3-pin XLR OUT
Electro-mechanical effects:
Light source:
55 x 3W RGBWA LEDs
Lumens:
1000 for each color
Lux @ 2 m:
475
Rotation speed:
8 RPM
Dimmer:
0-100%
Strobe:
0-12Hz
Housing:
Iron & flame retardant plastic
DMX control:
via standard DMX controller
Maximum distance:
20 m
Onboard:
4-digit LED display for easy setup
Control:
Built-in programs, Auto, Static Colors, Sound-controlled,
Master/Slave, DMX512
Connections:
Dedicated Schuko to IEC & data connector
Color:
Black
Cooling:
Internal fan
Max. ambient temperature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
1 m
Product Specifications
Design and product specifications are subject to change without prior notice.
Website:
Email: service@highlite.nl
17
www.Showtec.info
Ordercode: 43078
Sunraise LED
Dimensions
18
©2016 Showtec
Loading...