Page 1
Spectral Revo 6 IP65 V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Order code: 43640
MANUAL
ENGLISH
Page 2
1
Order code: 43640
Spectral Revo 6 IP65
Table of contents
Warning ............................................................................................................................................................................... 3
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the Mains ......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 7
Claims .............................................................................................................................................................................. 7
Description of the Device ................................................................................................................................................ 8
Installation ........................................................................................................................................................................... 9
Setup and Operation ........................................................................................................................................................ 9
Control Modes .............................................................................................................................................................10
One Spectral (Static Colors, Auto Programs) .....................................................................................................10
Multiple Spectrals (Master/Slave control) ...........................................................................................................10
Multiple Spectrals (DMX Control) ..........................................................................................................................11
Fixture Linking ...............................................................................................................................................................12
Data Cabling ...............................................................................................................................................................12
Control Panel ...............................................................................................................................................................13
DMX Addressing ..........................................................................................................................................................13
Menu Overview ...........................................................................................................................................................14
Main Menu Options ....................................................................................................................................................16
1. Static Colors ..........................................................................................................................................................16
2. DMX Address ........................................................................................................................................................17
3. Run Mode ..............................................................................................................................................................17
4. Personality (DMX Channel Modes) ..................................................................................................................17
5. Preset Color...........................................................................................................................................................17
6. Auto Programs .....................................................................................................................................................17
7. Edit ..........................................................................................................................................................................18
8. Settings ...................................................................................................................................................................19
8.1. Upload ................................................................................................................................................................19
8.2. Reset ...................................................................................................................................................................19
8.3. Dimmer ...............................................................................................................................................................19
8.4. DMX Error ............................................................................................................................................................20
8.5. PWM Rate ..........................................................................................................................................................20
8.6. Power CCT .........................................................................................................................................................20
8.7. Fans .....................................................................................................................................................................20
8.8. Mode Settings ...................................................................................................................................................20
8.9. XY Offset .............................................................................................................................................................20
8.10. UC ......................................................................................................................................................................20
9. Key (Display Lock) ...............................................................................................................................................21
10. Correlated Color Temperature Control (CCT) .............................................................................................21
11. Information..........................................................................................................................................................21
11.1. Version ..............................................................................................................................................................21
11.2. RDM ...................................................................................................................................................................21
DMX Channels .............................................................................................................................................................22
3 channels (Basic) ....................................................................................................................................................22
6 channels (CLR) ......................................................................................................................................................23
7 channels (HSIC) .....................................................................................................................................................23
9 channels (SSP) .......................................................................................................................................................24
13 channels (TOUR) .................................................................................................................................................25
20 channels (TR16) ...................................................................................................................................................27
Maintenance ....................................................................................................................................................................30
Troubleshooting ...............................................................................................................................................................30
Page 3
2
Order code: 43640
Spectral Revo 6 IP65
No Light .........................................................................................................................................................................30
No Response to DMX..................................................................................................................................................30
Product Specifications ....................................................................................................................................................32
Dimensions ........................................................................................................................................................................33
Notes ..................................................................................................................................................................................34
Page 4
3
Order code: 43640
Spectral Revo 6 IP65
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture will be returned in the original factory box and
packing.
Your shipment includes:
● Showtec Spectral Revo 6 IP65
● Schuko to PowerCON True1 power
cable (1,5 m)
● Safety cable
● User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Page 5
4
Order code: 43640
Spectral Revo 6 IP65
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
● Never remove warning or informative labels from the unit.
● Never use anything to cover the ground contact.
● Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
● Never place any material over the lens.
● Never look directly into the light source.
● Never leave any cables lying around.
● Do not connect this device to a dimmer pack.
● Do not switch the device on and off in short intervals, as this will reduce the device’s life.
● Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
● Do not shake the device. Avoid brute force when installing or operating the device.
● Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to acids, flammable liquids or gases.
● Always keep the case closed while operating.
● Always allow a free air space of at least 80 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
● Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
● If the lens is obviously damaged, it has to be replaced.
● If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material) and return it to your Showtec dealer for service.
● For adult use only. The fixture must be installed beyond the reach of children. Never leave the unit
running unattended.
● The user is responsible for correct positioning and operating of the Spectral. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
● This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
Page 6
5
Order code: 43640
Spectral Revo 6 IP65
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light output and the illuminated surface must be bigger than 0,8 m.
● The maximum ambient temperature t
a
= 40 °C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
● If the Spectral is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the Spectral with the mounting bracket to the trussing system.
● The Spectral must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
● When rigging, derigging or servicing the Spectral, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
Page 7
6
Order code: 43640
Spectral Revo 6 IP65
The Spectral Revo 6 IP65 can be placed on a flat stage floor or mounted to any kind of truss with a clamp
or a combination of a quick lock bracket and a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the Mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Page 8
7
Order code: 43640
Spectral Revo 6 IP65
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.com and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.
Page 9
8
Order code: 43640
Spectral Revo 6 IP65
Description of the Device
Features
The Spectral Revo 6 is an IP-65 rated outdoor fixture with a single lens. The 125-W custom Osram RGBALC
LED source guarantees homogenous output and is able to produce a full spectrum of light.
● Input voltage: 100-240 V AC, 50/60 Hz
● Power consumption: 145 W max
● Light source: 125 W custom Osram RGBALC LED Array
● Color range: 16,7 million additive colors with full saturation control
● Maximum flux: 3051 lm
● Peak intensity: 28987 cd
● Dimmer: 0-100 %
● Strobe: 0-20 Hz
● Beam angle: 17°
● Control protocol: DMX-512, RDM
● DMX personalities: Basic (3 CH), CLR (6 CH), HSIC (7 CH), SSP (9 CH), Tour (13 CH), TR16 (20 CH)
● Control: Static Colors, Auto, Master/Slave, DMX-512
● On-board: OLED display
● Housing: die-cast aluminum, black
● Connections: IP-65 rated power connectors True1 IN/OUT, IP-65 rated 5-pin DMX IN/OUT connectors
● Cooling: forced convection
● IP Rating: IP65
● Dimensions: 425 x 320 x 219 mm (L x W x H) (including bracket)
● Weight: 6,1 kg
Front View
Fig. 01
01) Mounting bracket with 2 adjustment screws
02) Safety eye
03) 125 W custom Osram RGBALC LED Array
04) Color frame retaining clip
Page 10
9
Order code: 43640
Spectral Revo 6 IP65
Back View
Fig. 02
05) IP-65 rated 5-pin DMX signal connector IN
06) Control panel: OLED display and touch buttons
07) IP-65 rated 5-pin DMX signal connector OUT
08) IP-65 rated power connector True 1 OUT
09) IP-65 rated power connector True 1 IN
Installation
Remove all packing materials from the Spectral Revo 6 IP65. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Setup and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120 V specification product on 230 V power, or vice versa.
Connect the device to the main power supply.
Page 11
10
Order code: 43640
Spectral Revo 6 IP65
Control Modes
There are 4 modes:
● Manual (Static Colors)
● Built-in and Custom Programs (Auto Programs)
● Master/Slave
● DMX-512 (3CH, 6CH, 7CH, 9CH, 13CH, 20CH)
One Spectral (Static Colors, Auto Programs)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 0,8 m on all sides
for air circulation.
02) Secure the device with the supplied safety cable.
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Spectral is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 16-17 for more information about the Static Colors and Auto Programs.
Multiple Spectrals (Master/Slave control)
01) Fasten the effect light onto firm trussing or mount it on flat surface. Leave at least 0,8 m on all sides for
air circulation.
02) Secure the device with the supplied safety cable.
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 5-pin XLR cable to connect the Spectral to other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
4. N/C
5. N/C
05) Link the units as shown in Fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX cable. Repeat this process to link the rest of the units. Refer to 3. Run Mode on
page 17 and 8.8. Mode Settings on page 20 to set up the master and the slave devices. You can set
the desired operation mode on the master device and all slave devices will react the same as the
master device.
Fig. 03
Page 12
11
Order code: 43640
Spectral Revo 6 IP65
Multiple Spectrals (DMX Control)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 0,8 m on all sides
for air circulation.
02) Secure the device with the supplied safety cable.
03) Use a 5-pin DMX cable to connect the Spectral and other devices.
04) Link the units as shown in Fig. 04. Connect a light controller to the first unit's DMX "in" socket, using a
DMX cable. Connect the first unit’s "out" socket with the second unit's "in" socket, using a DMX
cable. Repeat this process to link the rest of the units.
05) Supply electric power: Plug electric mains power cords into each unit's power IN socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 04
Note : Link all cables before connecting electric power
Page 13
12
Order code: 43640
Spectral Revo 6 IP65
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link: @110 V: 10 fixtures
Maximum recommended number of fixtures on a power link: @240 V: 24 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
● DAP Audio DMX cable by Neutrik®. Order code FL71150 (1,5 m), FL713 (3 m), FL716 (6 m),
FL7110 (10 m).
● DAP Audio DMX by Neutrik®. Order code FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m),
FL7210 (10 m).
● DAP Audio 110 Ohm cable with digital signal transmission. Order code FL0975 (0,75 m), FL09150
(1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
Note: Connect the Spectrals with the dedicated special DMX cables for outdoor use.
FL83150
DMX cable 5p XLR IP65, Neutrik®, 1,5 m
FL833
DMX cable 5p XLR IP65, Neutrik®, 3 m
FL836
DMX cable 5p XLR IP65, Neutrik®, 6 m
FL8310
DMX cable 5p XLR IP65, Neutrik®, 10 m
FL8320
DMX cable 5p XLR IP65, Neutrik®, 20 m
Page 14
13
Order code: 43640
Spectral Revo 6 IP65
The Spectral Revo 6 IP65 can be operated with controller or without controller in stand-alone mode.
Control Panel
A) OLED display
B) DOWN touch button
C) UP touch button
D) ENTER touch button
E) MENU touch button
Fig. 05
DMX Addressing
The control panel on the back side of the device allows you to assign the DMX fixture address, which is
the first channel from which the Spectral will respond to the controller. Please note when you use the
controller, the unit has 20 channels. When using multiple Spectral fixtures, make sure you set the DMX
addresses right. Therefore, the DMX address of the first Spectral should be 1 (001); the DMX address of the
second Spectral should be 1+20=21 (021); the DMX address of the third Spectral should be 21+20=41
(041), etc. Make sure that you do not have any overlapping channels in order to control each Spectral
correctly. If two or more fixtures are addressed similarly, they will work similarly.
Controlling:
After having addressed all Spectral fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Spectral will automatically detect whether DMX 512 data is received or not.
If there is DMX signal, at the top right corner of the display there will appear an antenna symbol.
If the DMX signal is lost, the antenna symbol will disappear. The problem may be:
● The DMX cable from the controller is not connected with the input of the Spectral.
● The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert a termination plug (with 120 Ohm) in the last fixture in order to ensure proper
transmission on the DMX data link.
Display Off after 10 seconds
When no button is pressed for 10 seconds, the display will turn off.
To light up the display, press any of the buttons: MENU, ENTER, UP or DOWN.
Page 15
14
Order code: 43640
Spectral Revo 6 IP65
Menu Overview
Page 16
15
Order code: 43640
Spectral Revo 6 IP65
Page 17
16
Order code: 43640
Spectral Revo 6 IP65
Main Menu Options
Upon start-up the display will show the Showtec logo.
By default the display of the device is locked. To unlock the display and access the Main Menu, you will
need to enter the password:
01) Press and hold the MENU button for 6 seconds to light up the display.
02) Press the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN.
03) Press the ENTER button to confirm.
To change the settings and remove the display lock, see 9. Key (Display Lock) on page 21.
If no button is pressed after 10 seconds, the display will turn off. Enter the password to unlock the display.
If the display lock is turned off, press any button to turn the display on.
● Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values.
● Use the ENTER button to open the desired menu or to set the currently selected value.
● Use the MENU button to exit the current menu and/or to return to the Main Menu.
The Main Menu has the following options:
01) Press the UP/DOWN buttons to navigate through the Main Menu.
02) Press the ENTER button to open the submenu.
Note: Some of the submenus require a password. The default password is pressing the UP/DOWN buttons
in the following order: UP, DOWN, UP, DOWN. Deactivating the display lock does not affect the submenu
items which by default require a password.
1. Static Colors
In this menu, you can set the static colors to create an infinite range of colors.
01) Press the UP/DOWN buttons to scroll through the static colors (RED, GREEN, BLUE, AMBER, LIME,
CYAN) and STROBE.
02) Press the ENTER button to open the settings submenu.
03) Press the UP/DOWN buttons to increase/decrease the values.
● Color intensity (RED, GREEN, BLUE, AMBER, LIME, CYAN): the adjustment range is between 0-255,
from low to high intensity
● STROBE frequency: the adjustment range is between 0-25, from OFF to high frequency
04) Press the ENTER button to set the value and to move to the next setting.
Page 18
17
Order code: 43640
Spectral Revo 6 IP65
2. DMX Address
In this menu you can set the device’s DMX starting address.
01) Press the UP/DOWN buttons to set the desired DMX address. The adjustment range is between 001
and 512.
02) Press the ENTER button to save the changes.
3. Run Mode
In this menu you can set the control mode of the device.
01) Press the UP/DOWN buttons to toggle between the following 2 options:
● DMX – the device will operate in DMX Mode.
● SLAVE – the device will operate as a slave in Master/Slave Mode. It means that it will react the
same as the master device.
02) Press the ENTER button to confirm your choice.
4. Personality (DMX Channel Modes)
In this menu you can set the DMX Channel Mode (Personality).
01) Press the UP/DOWN buttons to select the desired DMX channel mode. There are 6 options available:
Basic:
3 channels
SSP:
9 channels
CLR:
6 channels
TOUR:
13 channels
HSIC:
7 channels
TR16:
20 channels
02) Press the ENTER button to confirm your choice. See pages 22-29 for the DMX Channel Modes.
5. Preset Color
In this menu you can choose a preset color mix.
01) Press the UP/DOWN buttons to select one of the 16 presets: L106, R05, L194, R54, L019, R08, R89, R86,
L213, R377, R80, L202, L328, R3314, L101, L768.
02) Press the ENTER button to confirm your choice.
6. Auto Programs
In this menu you can select a built-in auto program or a custom program. There are 10 uneditable auto
programs and 10 custom programs, which can be edited in the Edit menu (see page 18):
01) Press the UP/DOWN buttons to choose an auto or a custom program.
02) Press the ENTER button to confirm your choice. If you have chosen one of the auto programs, after
pressing the ENTER button you can additionally adjust the speed.
03) Press the UP/DOWN buttons to set the program speed. The adjustment range is between 0-255, from
slow to fast.
04) Press the ENTER button to set the speed.
Page 19
18
Order code: 43640
Spectral Revo 6 IP65
7. Edit
In this menu you can edit the custom programs thus creating your own custom show.
01) Press the UP/DOWN buttons to choose the custom program you want to edit (CUSTOM.1 -
CUSTOM.10).
02) Press the ENTER button to confirm the selection. Each custom program has 30 scenes, which can be
edited:
03) Press the UP/DOWN buttons to select the desired scene.
04) Press the ENTER button to enter the scene settings.
05) Press the UP/DOWN buttons to scroll through the 6 colors (RED, GREEN, BLUE, AMBER, LIME, CYAN),
and the STROBE, TIME and FADE options.
06) Press the ENTER button to open the settings submenu.
07) Press the UP/DOWN buttons to increase/decrease the values.
● Color intensity (RED, GREEN, BLUE, AMBER, LIME, CYAN): the adjustment range is between 0-255,
from low to high intensity
● STROBE frequency: the adjustment range is between 0-25, from OFF to high frequency
● TIME (duration of the scene): the adjustment range is between 0-255, from 0 to 255 seconds
● FADE (transition time between the scenes): the adjustment range is between 0-255, from 0 to
255 seconds.
08) Press the ENTER button to set the value and to move to the next setting.
Note: For each custom program you can create 30 scenes, which makes it possible to create 300
customized scenes in total.
Page 20
19
Order code: 43640
Spectral Revo 6 IP65
8. Settings
In this menu you can adjust the device’s settings. This menu requires a password. The default password is
pressing the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN.
01) Enter the password to access the menu.
02) Press the ENTER button to confirm the password.
03) Press the UP/DOWN buttons to scroll through the following options:
8.1. Upload
In this submenu you can export the custom programs from the master device to the connected slave
devices.
01) Select UPLOAD and press the ENTER button to open the submenu.
02) Enter the password, pressing the buttons in the following order: UP, DOWN, UP, DOWN.
03) Press the ENTER button to confirm. During upload the display will show:
When the upload is finished, the display will show OK.
04) Press the ENTER button to confirm and exit the submenu.
8.2. Reset
In this submenu you can restore the default factory settings and reset the custom programs.
01) Select RESET and press the ENTER button to open the submenu.
02) Enter the password, pressing the buttons in the following order: UP, DOWN, UP, DOWN.
03) Press the ENTER button to confirm. During reset the display will show:
When the resetting is finished, the display will show OK.
04) Press the ENTER button to confirm and exit the submenu.
8.3. Dimmer
In this submenu you can adjust the dimmer speed.
01) Select DIMMER and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to choose one of the following options:
● DIM 1, DIM 2, DIM 3, DIM 4 – non-linear dimmers, from fast to slow
● OFF – linear dimmer
03) Press the ENTER button to confirm your choice.
Page 21
20
Order code: 43640
Spectral Revo 6 IP65
8.4. DMX Error
In this submenu, you can determine the behavior of the device in case of a DMX failure.
01) Select DMX ERROR and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to toggle between the following 2 options:
● SAVE: in case of a DMX signal failure the device will use the last properly received DMX signal
ensuring uninterrupted performance
● BLACK: in case of a DMX signal failure the device will black out the light output
03) Press the ENTER button to confirm your choice.
8.5. PWM Rate
In this submenu you can set the PWM (Pulse Width Modulation) frequency.
01) Select PWM Rate and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to choose the desired PWM frequency. The available options are 600 Hz,
1200 Hz, 2000 Hz, 4000 Hz, 6000 Hz, and 25000 Hz.
Note: The higher the PWM frequency, the lower the dimmer’s grayscale
03) Press the ENTER button to confirm your choice.
8.6. Power CCT
In this submenu you can set the color temperature.
01) Select POWER CCT and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to choose the desired color temperature. The available options are:
2700 K, 3200 K, 4200 K and NORMAL.
03) Press the ENTER button to confirm your choice.
8.7. Fans
In this submenu you can adjust the speed of the cooling fans.
01) Select FANS and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to choose the desired fan speed. The available options are: SLOW,
NORMAL, FAST and AUTO.
03) Press the ENTER button to confirm your choice.
8.8. Mode Settings
In this submenu you can set the device to perform as a master.
01) Select MODE SETTINGS and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to toggle between the following 2 options:
● SELF: the device will operate as a stand-alone
● MASTER: the device will operate as a master in Master/Slave mode
03) Press the ENTER button to confirm your choice.
8.9. XY Offset
In this submenu you can enable the color temperature calibration.
01) Select XY OFFSET and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to toggle between the following 2 options:
● HIDE: color temperature calibration will be disabled
● SHOW: color temperature calibration will be enabled. See 10. Correlated Color Temperature
Control (CCT) on page 21 for more information
03) Press the ENTER button to confirm your choice.
8.10. UC
In this submenu you can calibrate the colors.
01) Select UC and press the ENTER button to open the submenu.
02) Press the UP/DOWN buttons to scroll through the static colors: RED, GREEN, BLUE, AMBER, LIME and
CYAN.
03) Press the ENTER button to open the settings submenu.
04) Press the UP/DOWN buttons to adjust the color intensity. The adjustment range is between 0-255, from
low to high intensity.
05) Press the ENTER button to set the value and to move to the next color.
Page 22
21
Order code: 43640
Spectral Revo 6 IP65
9. Key (Display Lock)
In this menu you can activate the display lock.
01) Press the UP/DOWN buttons to toggle between ON and OFF.
● ON: display lock is on. The display turns off after 10 seconds of inactivity. To access the Main
Menu, you will need to enter the password. The default password is pressing the UP/DOWN
buttons in the following order: UP, DOWN, UP, DOWN.
● OFF: the Main Menu remains unlocked after the display turns off.
Note: Deactivating the display lock does not affect the submenu items which by default require a
password.
10. Correlated Color Temperature Control (CCT)
In this menu you can calibrate the color temperature. This menu requires a password. The default
password is pressing the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN.
01) Enter the password to access the menu.
02) Press the ENTER button to confirm the password.
03) Press the UP/DOWN buttons to scroll through the following options:
04) Press the ENTER button to open the submenu.
05) Press the UP/DOWN buttons to choose between X FINE and Y FINE.
06) Press the ENTER button to confirm the selection.
07) Press the UP/DOWN buttons to increase/decrease the value. The adjustment range is between -200
and +200.
08) Press the ENTER button to set the value.
11. Information
In this menu you can view the current software version and the RDM details of the device.
01) Press the UP/DOWN buttons to choose between VERSION and RDM.
02) Press the ENTER button to confirm the selection.
11.1. Version
If you have chosen VERSION, the display will show the current version of the installed firmware:
11.2. RDM
In this submenu you can view the RDM details of the device.
01) Press the UP/DOWN buttons to choose between UID and LABEL.
02) Press the ENTER button to confirm the selection.
● UID – the display shows the unique identification number of the device
● LABEL – the display shows the name of the device
Page 23
22
Order code: 43640
Spectral Revo 6 IP65
DMX Channels
3 channels (Basic)
Channel 1 – Dimmer intensity
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Color presets
0-10
No function
11-20
L106
21-30
R05
31-40
L194
41-50
R54
51-60
L019
61-70
R08
71-80
R89
81-90
R86
91-100
L213
101-110
R377
111-120
R80
121-130
L202
131-140
L328
141-150
R3314
151-160
L101
161-170
L768
171-255
No function
Channel 3 – Color macros and CCT
0-10
No function
11-30
Red 100 % / Green Up / Blue 0 %
31-50
Red Down / Green 100 % / Blue 0 %
51-70
Red 0 % / Green 100 % / Blue Up
71-90
Red 0 % / Green Down / Blue 100 %
91-110
Red Up / Green 0 % / Blue 100 %
111-130
Red 100 % / Green 0 % / Blue Down
131-150
Red 100 % / Green Up / Blue Up
151-170
Red Down / Green Down / Blue 100 %
171-195
All LEDs at full output
196-199
1800 K
200-203
2200 K
204-207
2700 K
208-211
3000 K
212-215
3200 K
216-219
3500 K
220-223
4000 K
224-227
4200 K
228-231
4500 K
232-235
5600 K
236-239
6000 K
240-243
6500 K
244-247
7200 K
248-255
8000 K
Page 24
23
Order code: 43640
Spectral Revo 6 IP65
6 channels (CLR)
Channel 1 – Red
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Green
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 3 – Blue
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 4 – Amber
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 5 – Lime
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 6 – Cyan
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
7 channels (HSIC)
Channel 1 – Dimmer intensity
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Hue CH1 and CH4 must be open
0-255
Gradual adjustment Hue, from 0-100 %
Channel 3 – Hue fine CH1, CH2 and CH4 must be open
0-255
Gradual adjustment Hue Fine, from 0-100 %
Channel 4 – Saturation CH1 must be open
0-255
Saturation adjustment, from 0-100 %
Channel 5 – CCT CH1 must be open
0-10
No function
11-28
1800 K
29-46
2200 K
47-64
2700 K
65-82
3000 K
83-100
3200 K
101-118
3500 K
119-136
4000 K
137-154
4200 K
155-172
4500 K
173-190
5600 K
191-208
6000 K
209-226
6500 K
227-244
7200 K
245-255
8000 K
Page 25
24
Order code: 43640
Spectral Revo 6 IP65
Channel 6 – Strobe CH1-CH4 must be open or CH5 must be set between 11-255
0-9
No function
10-99
Strobe flash rate, from low to high frequency (0-20 Hz)
100-109
No function
110-179
Pulse strobe, from low to high rate
180-189
No function
190-255
Random strobe, from low to high rate
Channel 7 – Dimmer speed
0-9
No function
10-29
Linear dimmer
30-69
Non-linear dimmer 1 (fastest)
70-129
Non-linear dimmer 2
130-189
Non-linear dimmer 3
190-255
Non-linear dimmer 4 (slowest) – default
9 channels (SSP)
Channel 1 – Master Dimmer
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Red CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 3 – Green CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 4 – Blue CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 5 – Amber CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 6 – Lime CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 7 – Cyan CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 8 – Strobe CH1-CH7 must be open
0-9
No function
10-99
Strobe flash rate, from low to high frequency (0-20 Hz)
100-109
No function
110-179
Pulse strobe, from low to high rate
180-189
No function
190-255
Random strobe, from low to high rate
Channel 9 – Dimmer speed
0-9
No function
10-29
Linear dimmer
30-69
Non-linear dimmer 1 (fastest)
70-129
Non-linear dimmer 2
130-189
Non-linear dimmer 3
190-255
Non-linear dimmer 4 (slowest) – default
Page 26
25
Order code: 43640
Spectral Revo 6 IP65
13 channels (TOUR)
Channel 1 – Master Dimmer
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Red CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 3 – Green CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 4 – Blue CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 5 – Amber CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 6 – Lime CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 7 – Cyan CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 8 – Color presets CH1 must be open
0-10
No function
11-20
L106
21-30
R05
31-40
L194
41-50
R54
51-60
L019
61-70
R08
71-80
R89
81-90
R86
91-100
L213
101-110
R377
111-120
R80
121-130
L202
131-140
L328
141-150
R3314
151-160
L101
161-170
L768
171-255
No function
Page 27
26
Order code: 43640
Spectral Revo 6 IP65
Channel 9 – Color macros and CCT CH1 must be open
0-10
No function
11-30
Red 100 % / Green Up / Blue 0 %
31-50
Red Down / Green 100 % / Blue 0 %
51-70
Red 0 % / Green 100 % / Blue Up
71-90
Red 0 % / Green Down / Blue 100 %
91-110
Red Up / Green 0 % / Blue 100 %
111-130
Red 100 % / Green 0 % / Blue Down
131-150
Red 100 % / Green Up / Blue Up
151-170
Red Down / Green Down / Blue 100 %
171-195
All LEDs at full output
196-199
1800 K
200-203
2200 K
204-207
2700 K
208-211
3000 K
212-215
3200 K
216-219
3500 K
220-223
4000 K
224-227
4200 K
228-231
4500 K
232-235
5600 K
236-239
6000 K
240-243
6500 K
244-247
7200 K
248-255
8000 K
Channel 10 – Built-in programs and custom programs
0-40
No function
41-50
Auto 1
51-60
Auto 2
61-70
Auto 3
71-80
Auto 4
81-90
Auto 5
91-100
Auto 6
101-110
Auto 7
111-120
Auto 8
121-130
Auto 9
131-140
Auto 10
141-150
Program 1
151-160
Program 2
161-170
Program 3
171-180
Program 4
181-190
Program 5
191-200
Program 6
201-210
Program 7
211-220
Program 8
221-230
Program 9
231-255
Program 10
Channel 11 – Auto speed CH10 must be set between 41-140
0-255
Speed adjustment, from slow to fast
Page 28
27
Order code: 43640
Spectral Revo 6 IP65
Channel 12 – Strobe CH1-CH7 must be open or CH8 must be set between 11-170
0-9
No function
10-99
Strobe flash rate, from low to high frequency (0-20 Hz)
100-109
No function
110-179
Pulse strobe, from low to high rate
180-189
No function
190-255
Random strobe, from low to high rate
Channel 13 – Dimmer speed
0-9
No function
10-29
Linear dimmer
30-69
Non-linear dimmer 1 (fastest)
70-129
Non-linear dimmer 2
130-189
Non-linear dimmer 3
190-255
Non-linear dimmer 4 (slowest) – default
20 channels (TR16)
Channel 1 – Master Dimmer
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 2 – Dimmer Fine
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 3 – Red CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 4 – Red Fine CH1, CH2 and CH3 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 5 – Green CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 6 – Green Fine CH1, CH2 and CH5 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 7 – Blue CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 8 – Blue Fine CH1, CH2 and CH7 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 9 – Amber CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 10 – Amber Fine CH1, CH2 and CH9 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 11 – Lime CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Page 29
28
Order code: 43640
Spectral Revo 6 IP65
Channel 12 – Lime Fine CH1, CH2 and CH11 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 13 – Cyan CH1 must be open
0-255
Gradual adjustment of the brightness, from low to high intensity (0-100 %)
Channel 14 – Cyan Fine CH1, CH2 and CH13 must be open
0-255
Fine adjustment of the brightness, from low to high intensity (0-100 %)
Channel 15 – Color presets CH1 or CH2 must be open
0-10
No function
11-20
L106
21-30
R05
31-40
L194
41-50
R54
51-60
L019
61-70
R08
71-80
R89
81-90
R86
91-100
L213
101-110
R377
111-120
R80
121-130
L202
131-140
L328
141-150
R3314
151-160
L101
161-170
L768
171-255
No function
Channel 16 – Color macros and CCT CH1 or CH2 must be open
0-10
No function
11-30
Red 100 % / Green Up / Blue 0 %
31-50
Red Down / Green 100 % / Blue 0 %
51-70
Red 0 % / Green 100 % / Blue Up
71-90
Red 0 % / Green Down / Blue 100 %
91-110
Red Up / Green 0 % / Blue 100 %
111-130
Red 100 % / Green 0 % / Blue Down
131-150
Red 100 % / Green Up / Blue Up
151-170
Red Down / Green Down / Blue 100 %
171-195
All LEDs at full output
196-199
1800 K
200-203
2200 K
204-207
2700 K
208-211
3000 K
212-215
3200 K
216-219
3500 K
220-223
4000 K
224-227
4200 K
228-231
4500 K
232-235
5600 K
236-239
6000 K
240-243
6500 K
244-247
7200 K
248-255
8000 K
Page 30
29
Order code: 43640
Spectral Revo 6 IP65
Channel 17 – Built-in programs and custom programs
0-40
No function
41-50
Auto 1
51-60
Auto 2
61-70
Auto 3
71-80
Auto 4
81-90
Auto 5
91-100
Auto 6
101-110
Auto 7
111-120
Auto 8
121-130
Auto 9
131-140
Auto 10
141-150
Program 1
151-160
Program 2
161-170
Program 3
171-180
Program 4
181-190
Program 5
191-200
Program 6
201-210
Program 7
211-220
Program 8
221-230
Program 9
231-255
Program 10
Channel 18 – Auto speed CH17 must be set between 41-140
0-255
Speed adjustment, from slow to fast
Channel 19 – Strobe CH1-CH15 must be open or CH15 must be set between 11-170
0-9
No function
10-99
Strobe flash rate, from low to high frequency (0-20 Hz)
100-109
No function
110-179
Pulse strobe, from low to high rate
180-189
No function
190-255
Random strobe, from low to high rate
Channel 20 – Dimmer speed
0-9
No function
10-29
Linear dimmer
30-69
Non-linear dimmer 1 (fastest)
70-129
Non-linear dimmer 2
130-189
Non-linear dimmer 3
190-255
Non-linear dimmer 4 (slowest) – default
Page 31
30
Order code: 43640
Spectral Revo 6 IP65
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Spectral Revo 6 IP65 requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the lightoutput very quickly.
Keep connections clean. Disconnect electric power, and then wipe the DMX connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect two potential problem areas as: the power supply and the LEDs.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Spectral to your Showtec dealer.
03) If both of the above appear to be O.K., plug the unit in again.
04) If you are unable to determine the cause of the problem, do not open the Spectral, as this may
damage the unit and the warranty will become void.
05) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX settings. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
Page 32
31
Order code: 43640
Spectral Revo 6 IP65
Problem
Probable cause(s)
Solution
One or more fixtures
do not function at all
No power to the fixture
● Check if power is switched on and
cables are plugged in
Internal fuse blown
● Return the device to your local
Showtec dealer
Fixtures reset correctly,
but all respond
erratically or not at all
to the controller
The controller is not connected.
● Connect controller
5-pin XLR OUT of the controller does
not match XLR IN of the first fixture
on the link (i.e. signal is reversed)
● Install a phase reversing cable
between the controller and the first
fixture on the link
Fixtures reset correctly,
but some respond
erratically or not at all
to the controller
Poor data quality
● Check data quality. If much lower
than 100 percent, the problem may
be a bad data link connection, poor
quality or broken cables, missing
termination plug, or a defective
fixture disturbing the link
Bad data link connection
● Inspect connections and cables.
Correct poor connections. Repair or
replace damaged cables
Data link not terminated with
120 Ohm termination plug
● Insert termination plug in the DMX
OUT connector of the last fixture on
the link
Incorrect addressing of the fixtures
● Check address settings
One of the fixtures is defective and
disturbs data transmission on the link
● Bypass one fixture at a time until
normal operation is restored: unplug
both connectors and connect them
directly together
● Have the defective fixture serviced
by a qualified technician
5-pin XLR OUT on the fixtures does
not match (pins 2 and 3 reversed)
● Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
No light or LEDs cuts
out intermittently
Fixture is too hot
● Allow the fixture to cool down
● Make sure air vents and the front
lens are not blocked
● Turn up the air conditioning
LEDs damaged
● Disconnect the fixture and return it to
your dealer
The power supply settings do not
match local AC voltage and
frequency
● Disconnect fixture. Check settings
and correct if necessary
Page 33
32
Order code: 43640
Spectral Revo 6 IP65
Product Specifications
Model:
Showtec Spectral Revo 6 IP65
Input voltage:
100-240 V AC, 50/60 Hz
Power consumption:
145 W max
DMX linking:
30 pcs
Dimensions:
425 x 320 x 219 mm (L x W x H) (including bracket)
Weight:
6,1 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)
DMX personalities:
Basic (3 CH), CLR (6 CH), HSIC (7 CH), SSP (9 CH),
Tour (13 CH), TR16 (20 CH)
Signal input:
5-pin DMX IN
Signal output:
5-pin DMX OUT
Electro-mechanical properties:
Light source:
1 x 125 W custom Osram RGBALC LED Array
Maximum flux:
3051 lm
Peak intensity:
28987 cd
Beam angle:
17°
Dimmer:
0-100 %
Strobe:
0-20 Hz
Housing:
Die-cast aluminum, black
Control protocol:
DMX-512 and RDM
On-board:
OLED display
Control:
Static Colors, Auto, Master/Slave, DMX-512
Connections:
IP-65 rated power connectors True1 IN/OUT
IP-65 rated 5-pin DMX IN/OUT connectors
Cooling:
Forced convection
IP rating:
IP65
Ambient temperature ta:
-20 °C to 40 °C
Max. housing temperature tB:
80 °C
Minimum distance:
Minimum distance from flammable surfaces:
0,8 m
Minimum distance to lighted object:
1 m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: service@highlite.com
Page 34
33
Order code: 43640
Spectral Revo 6 IP65
Dimensions
Page 35
34
Order code: 43640
Spectral Revo 6 IP65
Notes
Page 36
©2019 Showtec
Loading...