Showtec QubiQ F1500 User guide

QubiQ F1500

Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands

Product code: 61080

USER MANUAL

ENGLISH

V1

1

QubiQ F1500
Product code: 61080

Preface

Thank you for purchasing this Showtec product.

The purpose of this user manual is to provide instructions for the correct and safe use of this product.

Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.

This user manual contains information concerning:

● Safety instructions

● Installation and operation of the device

● Intended and non-intended use of the device

● Maintenance procedures

● Troubleshooting

● Transport, storage and disposal of the device

Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.

©2022 Showtec. All rights reserved.

No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.

Design and product specifications are subject to change without prior notice.

For the latest version of this document or other language versions, please visit our website

www.highlite.com or contact us at [e-mail].

Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2

QubiQ F1500
Product code: 61080

Table of contents

1. Introduction .......................................................................................................................................................... 4

Before Using the Product .................................................................................................................................. 4

Intended Use ....................................................................................................................................................... 4

Product Lifespan ................................................................................................................................................. 4

Text Conventions ................................................................................................................................................ 4

Symbols and Signal Words ................................................................................................................................ 5

Symbols on the Information Label .................................................................................................................. 5

2. Safety .................................................................................................................................................................... 6

Warnings and Safety Instructions .................................................................................................................... 6

Requirements for the User ................................................................................................................................. 9

3. Description of the Device ................................................................................................................................. 10

Front View ..........................................................................................................................................................10

Back View ..........................................................................................................................................................11

Remote Control ................................................................................................................................................12

Product Specifications ....................................................................................................................................13

Dimensions .........................................................................................................................................................14

4. Installation .......................................................................................................................................................... 15

Safety Instructions for Installation ..................................................................................................................15

Personal Protective Equipment .....................................................................................................................15

Installation Site Requirements ........................................................................................................................15

Rigging ...............................................................................................................................................................15

Connecting to Power Supply .........................................................................................................................17

Power Linking of Multiple Devices .................................................................................................................17

5. Setup ................................................................................................................................................................... 18

Warnings and Precautions .............................................................................................................................18

Stand-alone Setup ...........................................................................................................................................18

DMX Connection ..............................................................................................................................................18

DMX-512 Protocol ...................................................................................................................................18

DMX Cables .............................................................................................................................................19

DMX Linking .............................................................................................................................................19

DMX Addressing ......................................................................................................................................20

6. Operation ........................................................................................................................................................... 21

Safety Instructions for Operation ...................................................................................................................21

Recommended Fog Fluid ...............................................................................................................................21

Filling the Tank ...................................................................................................................................................22

Emptying the Tank after Operation ..............................................................................................................25

Restarting the Device after Running the Tank empty ...............................................................................28

Control Modes ..................................................................................................................................................28

Manual Operation ...........................................................................................................................................29

Control Panel (Device) ..........................................................................................................................29

Start-up .....................................................................................................................................................30

Menu Overview (Device) .....................................................................................................................31

Main Menu Options (Device) ..............................................................................................................32

DMX Address .......................................................................................................................................32

Output Volume ...................................................................................................................................32

Fan Speed ...........................................................................................................................................32

Interval ..................................................................................................................................................33

Duration................................................................................................................................................33

Fluid Sensor ..........................................................................................................................................33

Pump Mode ........................................................................................................................................33

Restore Default ...................................................................................................................................34

About ....................................................................................................................................................34

Manual Operation with Remote Control .....................................................................................................35

3

QubiQ F1500
Product code: 61080

Remote Control ......................................................................................................................................36

Start up (Remote Control) ....................................................................................................................36

Main Menu (Remote Control) ..............................................................................................................37

Menu Overview (Remote Control) .....................................................................................................37

Setup .....................................................................................................................................................38

Output Volume ...................................................................................................................................39

Fan Speed ...........................................................................................................................................39

Duration................................................................................................................................................39

Interval ..................................................................................................................................................39

Save ......................................................................................................................................................39

Continuous Output ............................................................................................................................40

Timer / Interval ....................................................................................................................................40

Version ..................................................................................................................................................40

DMX Operation .................................................................................................................................................41

DMX Channels ........................................................................................................................................41

7. Troubleshooting ................................................................................................................................................. 42

8. Maintenance ..................................................................................................................................................... 43

Safety Instructions for Maintenance .............................................................................................................43

Preventive Maintenance ................................................................................................................................43

Basic Cleaning Instructions ...................................................................................................................44

Cleaning the Fluid Pipes ........................................................................................................................44

Corrective Maintenance ................................................................................................................................45

Replacing the Fuse ................................................................................................................................45

9. Deinstallation, Transportation and Storage .................................................................................................... 46

Instructions for Deinstallation ..........................................................................................................................46

Instructions for Transportation ........................................................................................................................46

Storage ...............................................................................................................................................................46

10. Disposal .............................................................................................................................................................. 46

11. Approval ............................................................................................................................................................. 46

4

QubiQ F1500
Product code: 61080

1. Introduction

Before Using the Product

Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.

After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.

Your shipment includes:

● Showtec QubiQ F1500

● Remote control

● 2 x safety eye

● Schuko to pro power cable (1,5 m)

● User manual

Fig. 01

Intended Use

This device is designed to be used as a professional fog effect. Any incorrect use may lead to hazardous
situations and result in injuries and material damage. This device is not suitable for households.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Product Lifespan

This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.

Text Conventions

Throughout the user manual the following text conventions are used:

● Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”

● References: References to chapters and parts of the device are in bold lettering, for example:

“Refer to 2. Safety”, “turn the adjustment screw (02)”

● 0–255: Defines a range of values

● Notes: Note: (in bold lettering) is followed by useful information or tips

5

QubiQ F1500
Product code: 61080

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs.

Always follow the instructions provided in this user manual.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.

Attention

Indicates important information for the correct operation and use of the
product.

Important

Read and observe the instructions in this document.

Electrical hazard

Hot surface

Eye damage hazard

Provides important information about the disposal of this product.

Symbols on the Information Label

This product is provided with an information label. The information label is located on the backside of the
device.

The information label contains the following symbols:

This device is designed for indoor use.

This device shall not be treated as household waste.
This device falls under IEC protection class I.

6

QubiQ F1500
Product code: 61080

2. Safety

Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.

Warnings and Safety Instructions

DANGER
Danger for children

For adult use only. The device must be installed beyond the reach of children.

● Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within

children’s reach. Packaging material is a potential source of danger for children.

DANGER
Electric shock caused by dangerous voltage inside

There are areas within the device where dangerous touch voltage (> 120 V DC) may be present.

● Do not open the device or remove any covers.

● Do not operate the device if the covers or the housing are open. Before operation, check if the

housing is firmly closed and all screws are tightly fastened.

● Disconnect the device from electrical power supply before service and maintenance, and when the

device is not in use.

DANGER
Electric shock caused by short-circuit

This device falls under IEC protection class I.

● Make sure that the device is electrically connected to ground (earth). Connect the device only to a

socket-outlet with ground (earth) connection.

● Do not cover the ground (earth) connection.

● Do not bypass the thermostatic switch or fuses.

● For replacement use fuses of the same type and rating only.

● Do not let the power cable come into contact with other cables. Handle the power cable and all

connections with the mains with caution.

● Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.

● Make sure that the power cable is not crimped or damaged. Examine the power cable periodically

for any defects.

● Do not immerse the device in water or other liquids. Do not install the device in a location where

flooding may occur.

● Do not use the device during thunderstorms. Disconnect the device from the electrical power supply

immediately.

7

QubiQ F1500
Product code: 61080

WARNING
Risk of explosion caused by incorrect handling

● Do not add flammable liquids such as perfume and alcohol to the fog fluid.

● Operate the device only with the fluids recommended in this user manual.

CAUTION
Risk of health problems

● Operate the device only with the fluids recommended in this user manual. Other fluids may contain

substances, which are hazardous for human health and environment.

● Always refer to the Safety Data Sheet (SDS) of the fluid before to use.

● Do not swallow the fluid.

● Do not point the fog output at face height.

● Make sure that you use the device in spaces that have good airflow.

Persons, who suffer from respiratory disorders, should avoid prolonged exposure to artificially produced
atmospheric effects.

Attention
Risk of fire

● Do not point the fog output at flames.

● Do not cover the air vents.

● Make sure that there is sufficient airflow around the device.

Attention
Power supply

● Before connecting the device to the power supply, make sure that the current, voltage and

frequency match the input voltage, current and frequency specified on the information label on the
device.

● Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the

required power consumption of the device.

Attention
General safety

● Do not operate the device without liquid.

● Do not point the fog output at smooth floors. The fog output can cause condensation, which can

make the floor slippery.

● Do not insert objects into the air vents.

● Do not switch the device on and off in short intervals. This decreases the device’s life.

● Do not shake the device. Avoid brute force when installing or operating the device.

8

QubiQ F1500
Product code: 61080

● If the device is dropped or struck, disconnect the device from the electrical power supply

immediately.

● If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it

on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.

● If the device fails to work properly, discontinue the use immediately.

Attention
For professional use only
This device shall be used only for the purposes it is designed for.

This device is designed to be used as a professional fog effect. Any incorrect use may lead to hazardous
situations and result in injuries and material damage.

● This device is not suitable for households.

● This device is not designed for permanent operation.

● This device does not contain user-serviceable parts. Unauthorized modifications to the device will

render the warranty void. Such modifications may result in injuries and material damage.

Attention
Before each use, examine the device visually for any defects.

Make sure that:

● The fluid tank is closed.

● All screws used for installing the device or parts of the device are tightly fastened and are not

corroded.

● The safety devices are not damaged.

● There are no deformations on housings, fixations and installation points.

● The power cables are not damaged and do not show any material fatigue.

9

QubiQ F1500
Product code: 61080

Attention
Do not expose the device to conditions that exceed the rated IP class conditions.

This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.

Requirements for the User

This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
dealer for more information.

Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.

Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.

Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

10

QubiQ F1500
Product code: 61080

3. Description of the Device

The Showtec QubiQ F1500 is a professional 1500 W fazer with a high airflow radial fan. This fazer is reliable,
safe and feature-rich. In addition, it has a practical and nice looking design. It will be your best smoking
friend at small to large venues.

The smoke intensity is seamlessly adjustable from 0–100 % with a sophisticated microcontroller for precise
control. Not only can you control the fazer manually, but also via DMX or included timer remote control.

The QubiQ F1500 is reliable since it can provide a continuous output and it has a comprehensive security.
It has an accurate and reliable temperature control (double over temperature protection), as well as a
sensor to know when the liquid is almost empty.

Front View

Fig. 02

01) 2,3 L tank

02) Carrying handle

03) Bracket

04) Safety eye

05) Adjustment screw

06) Fog output nozzle

11

QubiQ F1500
Product code: 61080

Back View

Fig. 03

07) LED display with Menu buttons

08) ON / OFF

09) Ground/earth connection

10) Pro power connector (Gray) OUT

11) Pro power connector (Blue) IN

12) Fuse F8AL /250 V

13) 3-pin DMX signal connector OUT

14) 3-pin DMX signal connector IN

15) 5-pin Remote control connector IN

12

QubiQ F1500
Product code: 61080

Remote Control

Fig. 04

16) Special 5-pin connector with 3,5 m cable

17) Control Wheel

18) Blue SETUP Button

19) Red PLUS / CONTI

20) Yellow MINUS / TIMER Button

21) Green ENTER / MANUAL Button

13

QubiQ F1500
Product code: 61080

Product Specifications

Model:

QubiQ F1500

Electrical:

Input voltage:

240 V AC, 50/60 Hz

Power consumption:

1500 W

Fuse:

F8AL /250 V

Physical:

Dimensions:

385 x 412 x 335 mm (LxWxH)

Weight:

15,1 kg

Fogger capacity:

Heater:

1500 W

Warm-up / Heating time:

4 minutes

Tank capacity:

2,3 L

Adjustable output level:

0–100 %

Safety:

Reliable and safe due to temperature protection and liquid sensor

Continuous and steady output till tank runs out of liquid

Operation and control:

Control:

DMX-512, Manual, Remote, Timer

DMX channels:

2 channels

Control panel:

LED display and buttons

Connections:

Power connections:

Pro power connectors (Blue) IN/(Gray) OUT

Data connections:

3-pin DMX connectors IN/OUT

Signal pinouts:

3-pin: pin 1 (ground), pin 2 (-), pin 3 (+)

Remote control connection:

5-pin connectors IN

Construction:

Housing:

Aluminum

Color:

Black

IP rating:

IP20

Cooling:

Convection

Thermal:

Minimum Ambient Temperature ta:

0 °C

Maximum ambient temperature ta:

40 °C

Maximum housing temperature tc:

70 °C

Minimum distance:

Minimum distance from flammable surfaces:

0,8 m

14

QubiQ F1500
Product code: 61080

Dimensions

Fig. 05

15

QubiQ F1500
Product code: 61080

4. Installation

Safety Instructions for Installation

WARNING
Incorrect installation can cause serious injuries and damage of property.

If trussing systems are used, installation must be carried out only by instructed or skilled persons.

Follow all applicable European, national and local safety regulations concerning rigging and trussing.

Personal Protective Equipment

During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.

Installation Site Requirements

● The device can be used only indoors.

● The device can be mounted to a truss or other rigging structure in any orientation.

● The minimum distance to other objects must be bigger than 0,8 m.

● The minimum distance between the light output and the illuminated surface must be bigger than

0,8 m.

● The maximum ambient temperature ta = 40 °C must never be exceeded.

● The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.

Rigging

The device can be positioned on a flat surface or mounted to a truss or other rigging structure in a
horizontal orientation. The maximum inclination angle of the device should not exceed 15º. Make sure
that all loads are within the pre-determined limits of the supporting structure.

CAUTION
Restrict the access under the work area during rigging and/or derigging.

16

QubiQ F1500
Product code: 61080

To mount the device, follow the steps below:

Use a clamp to attach the device to the supporting structure, as shown in Fig. 06. Make sure that the

device cannot move freely.

02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the

secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable through the safety eye (04), as shown in Fig. 06.

Fig. 06

17

QubiQ F1500
Product code: 61080

Connecting to Power Supply

DANGER
Electric shock caused by short-circuit

The device accepts AC mains power at 240 V and 50/60 Hz. Do not supply power at any other voltage or
frequency to the device.

This device falls under IEC protection class I. Make sure that the device is always electrically connected
to the ground (earth).

Before connecting the device to the socket-outlet:

● Make sure that the power supply matches the input voltage specified on the information label on

the device.

● Make sure that the socket-outlet has ground (earth) connection.

Connect the device to the socket-outlet with a power plug. Do not connect the device to a dimmer
pack, as this may damage the device.

Power Linking of Multiple Devices

This device supports power linking. Power can be relayed to another device via the power OUT
connector. Note that the input and the output connectors have different designs: one type cannot be
connected to the other.

Power linking of multiple devices must be carried out only by instructed or skilled persons.

WARNING
Incorrect power linking may lead to overload of the electrical circuit and result in serious
injuries and damage of property.

To prevent overload of the electrical circuit, when power linking multiple devices:

● Use cables with sufficient current-carrying capacity. The power cable supplied with the device is not

suitable for power linking of multiple devices.

● Make sure that the total current draw of the device and all connected devices does not exceed the

rated capacity of the power cables and the circuit breaker.

● Do not link more devices on one power link than the maximum recommended number.

Maximum recommended number of devices:

● at 220–240 V: 2 devices

18

QubiQ F1500
Product code: 61080

5. Setup

Warnings and Precautions

Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.

Stand-alone Setup

When the QubiQ F1500 is not connected to a controller or to other devices, it functions as a stand-alone
device. It can be operated manually.

For more information about the control mode, refer to 6.7.4.1. DMX Address on page 32.

DMX Connection

DMX-512 Protocol

You need a DMX serial data link to run fog shows of one or more devices using a DMX-512 controller or to
run synchronized shows of two or more devices set in a DMX mode.

The QubiQ F1500 has 3-pin DMX signal IN and OUT connectors.

The pin assignment is as follows:

● 3-pin: pin 1 (ground), pin 2 (-), pin 3 (+)

Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can
control on one data link is limited by the combined number of the DMX channels of the connected
devices and the 512 channels available in one DMX universe.

To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link.
In order to connect more than 32 devices on one data link, you must use a DMX optically isolated
splitter/booster, otherwise this may result in deterioration of the DMX signal.

Note:

● Maximum recommended DMX data link distance: 300 m

● Maximum recommended number of devices on a DMX data link: 32 devices

19

QubiQ F1500
Product code: 61080

DMX Cables

Shielded twisted-pair cables with 3-pin XLR connectors must be used for reliable DMX connection.
You can purchase DMX cables directly from your Highlite International dealer or make your own cables.

If you use 3-pin XLR audio cables for DMX data transmission, this may lead to signal degradation and
unreliable operation of the DMX network.

When you make your own DMX cables, make sure that you connect the pins and wires correctly as
shown in Fig. 07.

Fig. 07

DMX Linking

To connect multiple devices on one DMX data link, follow the steps below:

Use a 3-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN

connector of the first device.

02) Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a

3-pin DMX cable.

03) Repeat step 2 to connect all devices in a daisy-chain as shown in Fig. 08.

04) Connect a DMX terminator (120 Ω resistor) to the DMX OUT connector of the last device on the data

link.

20

QubiQ F1500
Product code: 61080

Fig. 08

DMX Addressing

In a setup with multiple devices, make sure that you set the DMX starting address of each device
correctly. The QubiQ F1500 has 1 personality: 2 channels.

If you want to connect multiple devices on one data link and use them in 2-channel mode, for example,
follow the steps below:

Set the starting address of the 1

st

device on the data link to 1 (001).

02) Set the starting address of the 2

nd

device on the data link to 2 (003), as 1 + 2 = 3.

03) Set the starting address of the 3

rd

device on the data link to 3 (005) as 3 + 2 = 5.

04) Continue assigning the starting addresses of the remaining devices by adding each time 2 to the

previous number.

Make sure that you do not have any overlapping channels in order to control each QubiQ F1500
correctly. If two or more devices are addressed similarly, they will work similarly.

21

QubiQ F1500
Product code: 61080

6. Operation

Safety Instructions for Operation

Attention
This device must be used only for the purposes it is designed for.

This device is designed to be used as a professional fog effect. Any incorrect use may lead to hazardous
situations and result in injuries and material damage. This device is not suitable for households.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Attention
Power supply

Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.

Recommended Fog Fluid

It is recommended to operate the device with the following fog fluids. Other fog liquids may cause poor
effect or damage the device.

● Product code: 60590 – Antari Smoke fluid 5 L Light version FLR-5

● Product code: 60595 – Antari Smoke fluid 5 L Heavy version FLG-5

● Product code: 60603 – Showgear Fog Fluid 5 L

● Product code: 60637 – Showgear Fog fluid 5 L High density

22

QubiQ F1500
Product code: 61080

Filling the Tank

WARNING
Risk of explosion caused by incorrect handling

● Do not add flammable liquids such as perfume and alcohol to the fog fluid.

● Operate the device only with the fluids recommended in this user manual.

● Make sure that you do not to exceed the maximum fluid level. Do not overfill!

To fill the tank, follow the steps below:

Lift the small ring on top of the device to open the service lid, as shown in Fig. 09.
Open the service lid, as shown in Fig. 10.

Fig. 09

Fig. 10

Remove the service lid, as shown in Fig. 11.
Place the service lid next to the device, as shown in Fig. 12.

Fig. 11

Fig. 12

23

QubiQ F1500
Product code: 61080

Do not disconnect the safety cable.
Unscrew the lid on the fluid tank, as shown in Fig. 13.
Take out the fluid tank, as shown in Fig. 14.

Fig. 13

Fig. 14

Place the fluid tank on a flat service near the device, as shown in Fig. 15.
Use a funnel to pour the fog fluid into the tank, as shown in Fig. 16.

Fig. 15

Fig. 16

Fill the fluid container with the recommended fog fluid ( Max. Fluid Tank Capacity 2,3 L). Make sure

that you do not overfill. See Fig. 16 for more information.

24

QubiQ F1500
Product code: 61080

Put the fluid tank back in the device, as shown in Fig. 17.
Screw the lid back on the fluid tank, as shown in Fig. 18.

Fig. 17

Fig. 18

Put the lid back on the device, as shown in Fig. 19.
Close the service lid, as shown in Fig. 20.

Fig. 19

Fig. 20

Wait for the device to heat up. This will take a maximum of 3 minutes.

Notes:

● Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid

container and the fog machine liquid tank immediately after filling.

25

QubiQ F1500
Product code: 61080

Emptying the Tank after Operation

To empty the tank, follow the steps below:

Lift the small ring on top of the device to open the service lid, as shown in Fig. 21.
Open the service lid, as shown in Fig. 22.

Fig. 21

Fig. 22

Remove the service lid, as shown in Fig. 23.
Place the service lid next to the device, as shown in Fig. 24.

Fig. 23

Fig. 24

26

QubiQ F1500
Product code: 61080

Do not disconnect the safety cable.
Unscrew the lid on the fluid tank, as shown in Fig. 25.
Take out the fluid tank, as shown in Fig. 26.

Fig. 25

Fig. 26

Place the fluid tank on a flat service near the device, as shown in Fig. 27.
Use a funnel to pour the fog fluid from the tank into original fog fluid jerry can, as shown in Fig. 28.

Fig. 27

Fig. 28

Fill the jerry can with the exact fog fluid. Do not mix different types of fog fluid. Make sure that you do

not overfill.

27

QubiQ F1500
Product code: 61080

Put the fluid tank back in the device, as shown in Fig. 29.
Screw the lid back on the fluid tank, as shown in Fig. 30.

Fig. 29

Fig. 30

Put the lid back on the device, as shown in Fig. 31.
Close the service lid, as shown in Fig. 32.

Fig. 31

Fig. 32

Notes:

Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid
container and the fog machine liquid tank immediately after filling.

28

QubiQ F1500
Product code: 61080

Restarting the Device after Running the Tank empty

When running a tank completely empty, the pump will automatically stop fogging to prevent damage to
the pump. The display will show:

If you refill the tank and try to operate the device, the display will keep displaying this Warning

message.

Make sure you fill the entire tank, let the device reheat and then manually start fogging.

This will take a few seconds until the completely emptied lines are filled with fog fluid.

Control Modes

The QubiQ F1500 supports the following control modes:

● Manual (fog intensity, duration, timer)

● Manual via Remote control (fog intensity, duration, timer, fan speed)

● 2 DMX channels

For more information about how to connect the devices, refer to 5. Setup on pages 18–20.

29

QubiQ F1500
Product code: 61080

Manual Operation

To set up the device, follow the steps below:

Fill the tank (Fluid Tank Capacity 2,3 L). See 6.3. Filling the Tank on page 22 for more information.
Connect the power cable before supplying power to the device. See 4.5. Connecting to Power

Supply on page 17 for more information.

Set the ON/OFF switch (08) to ON.
Wait for the device to heat up. This will take a maximum of 3 minutes.

When the device is not 100 % heated you cannot view the menu or change the settings.

To operate the device manually as a stand-alone device:

● Adjust the output volume in Output Vol menu. See 6.7.4.2. Output Volume on page 32 for more

information.

● Adjust the fan speed in Fan Speed menu. See 6.7.4.3. Fan Speed on page 32 for more information.

● Adjust the Interval volume in Interval menu. See 6.7.4.4. Interval on page 33 for more information.

● Adjust the Duration volume in Duration menu. See 6.7.4.5. Duration on page 33 for more information.

Notes:

● You can constantly fog @100 % until the tank is empty.

In order to constantly fog, you do not have to adjust the output volume.

● The remote control always has priority over manual operation with the control panel on the device.

You are not able to use the buttons on the device, when the remote is plugged in.

Control Panel (Device)

A) LCD display
B) MANUAL / ENTER button
C) TIMER / DOWN button
D) CONTI / UP button
E) SETUP button

Fig. 33

● Use the MANUAL / ENTER button to save your settings.

● Use the CONTI / UP and TIMER / DOWN buttons to increase/decrease numeric values.

● Use the SETUP button to navigate through the menus.

30

QubiQ F1500
Product code: 61080

Start-up

Upon start-up, the display will show the current software version and the temperature.

Before you are able to see the main menu or change settings, you have to wait until the device is fully
heated. The display will show:

31

QubiQ F1500
Product code: 61080

Menu Overview (Device)

Notes:

● The remote control always has priority over manual operation with the control panel on the device.

You are not able to use the buttons on the device, when the remote is plugged in.

● Do not connect the DMX cables and the remote control cable to the device at the same time. This

will cause data collisions.

32

QubiQ F1500
Product code: 61080

Main Menu Options (Device)

The main menu has the following options:

Press the SETUP button to navigate through the main menu.

DMX Address

In this menu you can set the DMX address.

Press the UP/DOWN buttons to set the desired DMX address. The adjustment range is 001–512.

Output Volume

In this menu you can manually set the output volume.

Press the UP/DOWN buttons to set the desired Output volume. The adjustment range is 1–100 %.

Fan Speed

In this menu you can manually set the fan speed.

Press the UP/DOWN buttons to set the desired fan speed. The adjustment range is 1–100 %.

33

QubiQ F1500
Product code: 61080

Interval

In this menu you can set the fog interval.

Press the UP/DOWN buttons to set the desired interval time. The adjustment range is 30–999 sec.

Duration

In this menu you can set the duration of the fog output.

Press the UP/DOWN buttons to set the desired duration of your fog output. The adjustment range is 30–999
sec.

Fluid Sensor

In this menu you can set the Fluid Sensor.

Press the UP/DOWN buttons to select one of the following 2 options:

● Yes: Sensor is on.

● NO: Sensor is off.

Pump Mode

In this menu you can set the Pump Mode.

Press the UP/DOWN buttons to select one of the following 3 options:

● A: Pump A is on.

● B: Pump B is on.

● A/B: Alternating between Pump A and Pump B.

34

QubiQ F1500
Product code: 61080

Restore Default

In this menu you can restore the default factory settings.

Press the UP/DOWN buttons to restore the default factory settings.

About

In this menu you can view the device’s model, the current software version and the software date.

Press the UP/DOWN buttons to see the current software version. The display will show.

35

QubiQ F1500
Product code: 61080

Manual Operation with Remote Control

To set up the device, follow the steps below:

Fill the tank (Fluid Tank Capacity 2,3 L). See 6.3. Filling the Tank on page 22 for more information.
Connect the remote control cable to the device.
Connect the power cable before supplying power to the device. See 4.5. Connecting to Power

Supply on page 17 for more information.

Set the ON/OFF switch (08) to ON.
Wait for the device to heat up. This will take a maximum of 3 minutes.

When the device is not 100 % heated you cannot view the menu or change the settings.

To operate the device manually as a stand-alone device:

● Adjust the output volume in Output Vol menu. See 6.8.4.2. Output Volume on page 39 for more

information.

● Adjust the Fan Speed in Fan Speed menu. See 6.8.4.3. Fan Speed on page 39 for more information

● Adjust the Duration volume in Duration menu. See 6.8.4.4. Duration on page 39 for more information.

● Adjust the Interval volume in Interval menu. See 6.8.4.5. Interval on page 39 for more information.

Notes:

● You cannot constantly fog @100 % until the tank is empty.

In order to constantly fog, you have to adjust the output volume to 40 %. Only then will the device
keep fogging until the tank is completely empty.

● The remote control always has priority over manual operation with the control panel on the device.

You are not able to use the buttons on the device, when the remote is plugged in.

36

QubiQ F1500
Product code: 61080

Remote Control

The device can be controlled with a remote control.

Fig. 34

Button

Function

Description

17
Increase/Decrease

Scroll through the Menu / Press control wheel to Save

18
Setup

Scroll through the Menu

19
Plus / Conti

Increase value / Continuous output

20
Minus / Timer

Decrease value / Timer

21
Enter / Manual

Enter / Manual Fog output

Start up (Remote Control)

Upon start-up, the display of the remote control will show the current software version and the
temperature.

Before you are able to see the main menu or change settings, you have to wait until the device is fully
heated. The display will show:

37

QubiQ F1500
Product code: 61080

Main Menu (Remote Control)

Notes:

● The remote control always has priority over manual operation with the control panel on the device.

You are not able to use the buttons on the device, when the remote is plugged in.

Menu Overview (Remote Control)

The main menu has the following options:

Press the UP/DOWN buttons or turn the CONTROL WHEEL to navigate through the main menu.

02) Press the SETUP button or the CONTROL WHEEL to open the submenus.

38

QubiQ F1500
Product code: 61080

Setup

In this menu you can set the output volume, duration and interval for the fog output.

Press the colored buttons, the UP/DOWN buttons or turn the CONTROL WHEEL to select the

parameter.

Press the green ENTER / MANUAL button to confirm the selection and open the submenu.

03) Press the UP/DOWN buttons or turn the CONTROL WHEEL to increase/decrease the values:

● RMTVOL: Set the intensity of the output volume. The adjustment range is 1–100 %,

from low to high output. See 6.8.4.2. Output Volume on page 39 for more
information.

● RMTFAN Set the intensity of the fan speed. The adjustment range is 1–100 %, from low

to high speed. See 6.8.4.3. Fan Speed on page 39 for more information.

● RMTDUR: Set the duration of the output. The adjustment range is 30–999 sec. See

6.8.4.4. Duration on page 39 for more information.

● RMTINT: Set the interval of the output. The adjustment range is 30–999 sec. See

6.8.4.5. Interval on page 39 for more information.

39

QubiQ F1500
Product code: 61080

Output Volume

In this menu you can continuously fog.

Press the UP/DOWN buttons or turn the CONTROL WHEEL to increase / decrease the output volume. The
adjustment range is 1–100 %.

Fan Speed

In this menu you can set the fan speed.

Press the UP/DOWN buttons or turn the CONTROL WHEEL to increase / decrease the fan speed. The
adjustment range is 1–100 %.

Duration

In this menu you can set the duration of the fog output.

Press the UP/DOWN buttons or turn the CONTROL WHEEL to increase / decrease to set the desired duration
of your fog output. The adjustment range is 30–999 sec.

Interval

In this menu you can set the fog interval.

Press the UP/DOWN buttons or turn the CONTROL WHEEL to increase / decrease the interval time. The
adjustment range is 30–999 sec.

Save

In this menu you can set the save the settings.

Press the UP/DOWN buttons to select one of the following 2 options:

● YES: Your settings will be saves.

● NO: Your settings will not be saved.

40

QubiQ F1500
Product code: 61080

Continuous Output

In this menu you continuously keep fogging until the tank is empty.

Press the red PLUS / CONTI button or press the CONTROL WHEEL to immediately start fogging at the

preset volume. To change the volume, see 6.8.4.2. Output Vol on page 39 for more information.

If you want to stop continuously fogging, press the red PLUS / CONTI button or press the CONTROL

WHEEL again.

Notes:

● You cannot constantly fog @100 % until the tank is empty.

In order to constantly fog, you have to adjust the output volume to 40 %. Only then will the device
keep fogging until the tank is completely empty.

Timer / Interval

In this menu you can set the fog timer and determine the interval.

Press the yellow MINUS / TIMER button or press the CONTROL WHEEL to start your timer program. To

change the interval time, see 6.8.4.5. Interval on page 39 for more information.

If you want to stop continuously fogging, press the yellow MINUS / TIMER button or press the CONTROL

WHEEL again.

Version

In this menu you can view the device’s model and the current software version.

41

QubiQ F1500
Product code: 61080

DMX Operation

To setup up the device, follow the steps below:

Fill the tank (Fluid Tank Capacity 2,3 L). See 6.3. Filling the Tank on page 22 for more information.
Connect the DMX cables before supplying power to the device. See 5.3. DMX Connection on page

18 for more information

Connect the power cable before supplying power to the device. See 4.5. Connecting to Power

Supply on page 17 for more information.

Set the ON/OFF switch (08) to ON.
Wait for the device to heat up. This will take a maximum of 3 minutes. When the device is not 100 %

heated you cannot view the menu or change the settings.

Set the DMX starting address of the device in Address menu. See 5.3.4. DMX Addressing on page 20

and 6.7.4.1. Address on page 32.

Notes:

● You can constantly fog @100 % until the tank is empty.

In order to constantly fog, you do not have to adjust the output volume.

● The remote control always has priority over manual operation with the control panel on the device.

You are not able to use the buttons on the device, when the remote is plugged in.

DMX Channels

2 CH

Function

Value

Setting

1

Output

000–255

Fog output 0-100 %

2

Fan

000–255

Fan Speed 0-100 %

42

QubiQ F1500
Product code: 61080

7. Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary
person. The device does not contain user-serviceable parts.

Unauthorized modifications to the device will render the warranty void. Such modifications may result in
injuries and material damage.

Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the
solution is not described in the table.

Problem

Probable cause(s)

Solution

The device does not
function at all

No power to the device

● Check if power is switched on and cables

are plugged in

Main fuse is blown

● Replace the fuse. See 8.3.1. Replacing

the Fuse on page 45

The device responds
erratically

The factory settings of the device
are changed

● Reset the device’s parameters to the

default factory settings. See 6.7.4.8.
Restore Default on page 34

The device does not
respond to DMX
control

The controller is not connected

● Connect the controller

The signal is reversed. The 3-pin/5-pin
DMX OUT of the controller does not
match the DMX IN of the device

● Install a phase-reversing cable between

the controller and the device

The controller is defective

● Try using another controller

The device responds
erratically to DMX
control

Bad data link connection

● Examine connections and cables.

Correct poor connections. Repair or
replace damaged cables

The data link is not terminated with a
120 Ω termination plug

● Insert a termination plug in the DMX OUT

connector of the last device on the link

Incorrect addressing

● Check address settings and correct, if

necessary

In case of a setup with multiple
devices, one of the devices is
defective and disturbs data
transmission on the link

● To find out the defective device, bypass

one device at a time until normal
operation is restored

No fog output

Device is too hot

● Allow device to cool down.

● Make sure that air vents are not blocked.

The device is damaged

● Disconnect the device and contact your

Highlite International dealer

The power supply settings do not
match local AC voltage and
frequency

● Disconnect the device. Check the

settings and correct, if necessary

The fluid pipes or the fog output
nozzle (06) are clogged.

● Clean the fluid pipes. See 8.2.1. Basic

Cleaning Instructions and 8.2.2.

Cleaning the Fluid Pipes on page 44

Incompatible fog fluid

● Use the recommended fog fluid. See 6.2.

Recommended Fog Fluid on page 21

Fog output nozzle is
sputtering

Incompatible fog fluid

● Use the recommended fog fluid. See 6.2.

Recommended Fog Fluid on page 21

Device does not
function correctly.
(Error message: Fluid
Lack!)

Tank is empty

● Fill the tank. See 6.3. Filling the Tank on

page 22

Fluid pipes are empty

● Restart the device. See 6.5. Restarting the

Device after Running the Tank empty on

page 28

43

QubiQ F1500
Product code: 61080

8. Maintenance

Safety Instructions for Maintenance

DANGER
Electric shock caused by dangerous voltage inside

Disconnect power supply before servicing or cleaning.

WARNING
Risk of burns due to hot surface

Allow the device to cool down for at least 15 minutes before servicing or cleaning.

Preventive Maintenance

Attention
Before each use, examine the device visually for any defects.

Make sure that:

● All screws used for installing the device or parts of the device are tightly fastened and are not

corroded.

● The safety devices are not damaged.

● There are no deformations on housings, fixations and installation points.

● The lens is not cracked or damaged.

● The power cables are not damaged and do not show any material fatigue.

44

QubiQ F1500
Product code: 61080

Basic Cleaning Instructions

The device must be cleaned periodically from the built-up dust and fog fluid residues.

To clean the device, follow the steps below:

Disconnect the device from the electrical power supply.
Allow the device to cool down for at least 1 hour.
Remove the dust collected on the external surface with dry compressed air and a soft brush.
Clean the fog fluid residues from the fog output nozzle (06) with a damp cloth. Use only a clean, lint-

free soft cloth.

Clean the DMX and other connections with a damp cloth.

Attention

● Do not immerse the device in liquid.

● Do not use alcohol or solvents.

● Make sure that the connections are fully dry before connecting the device to the power supply and

to other devices.

Cleaning the Fluid Pipes

The device must be cleaned periodically from the fog fluid residues. After every 40 hours of continuous
operation, it is recommended to run a cleaning solution composed of 80 % distilled water and 20 % white
vinegar through the system.

To clean the device, follow the steps below:

Disconnect the device from the electrical power supply.
Allow the device to cool down for at least 1 hour.
Clean out debris with vinegar and a pipe cleaner, making sure that the fog output nozzle (06) is free

of clogs.

Remove all fog liquid from the tank. See 6.4. Emptying the Tank after operation on page 25 for more

information.

Add a cleaning solution to tank.
Connect the power cable before supplying power to the device. See 4.5. Connecting to Power

Supply on page 17 for more information.

Make sure that you run the device until tank is empty.
Make sure that you use the device in spaces that have good airflow.
Repeat this 2-4 times.
Refill with fog liquid.

45

QubiQ F1500
Product code: 61080

Corrective Maintenance

The device does not contain user-serviceable parts. Do not open the device and do not modify the
device.

Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for
more information.

Replacing the Fuse

DANGER
Electric shock caused by short-circuit

● Do not bypass the thermostatic switch or fuses.

● For replacement use fuses of the same type and rating only.

Power surges, short-circuit or incorrect electrical power supply may cause a fuse to burn out. If the fuse
burns out, the device will not function anymore. If this happens, follow the steps below.

Disconnect the device from the electrical power supply.

02) Allow the device to cool down for at least 15 minutes.

03) Loosen the fuse cover with a screwdriver and remove the fuse holder.

04) If the fuse is brown or unclear, it is burned out. Remove the old fuse.

05) Insert a new fuse in the fuse holder. Make sure that the type and the rating of the replacement fuse

are the same as the ones specified on the information label of the product.

06) Replace the fuse holder in the opening and tighten the fuse cover.

46

QubiQ F1500
Product code: 61080

9. Deinstallation, Transportation and Storage

Instructions for Deinstallation

WARNING
Incorrect deinstallation can cause serious injuries and damage of property.

● Let the device cool down before dismounting.

● Disconnect power supply before deinstallation.

● Always observe the national and site-specific regulations during deinstallation and derigging of the

device.

● Wear personal protective equipment in compliance with the national and site-specific regulations.

Instructions for Transportation

● Make sure that the liquid tank is empty before transportation.

● Use the original packaging to transport the device, if possible.

● Always observe the handling instructions printed on the outer carton box, for example: “Handle with

care”, “This side up”, “Fragile”.

Storage

● Make sure that the liquid tank is empty before storing the device. See 6.4. Emptying the Tank after

operation on page 25 for more information.

● Clean the device before storing. Follow the cleaning instructions in chapter 8.2.1. Basic Cleaning

Instructions and 8.2.2. Cleaning the Fluid Pipes on page 44.

● Store the device in the original packaging, if possible

10. Disposal

Correct disposal of this product

Waste Electrical and Electronic Equipment

This symbol on the product, its packaging or documents indicates that the product
shall not be treated as household waste. Dispose of this product by handing it to the
respective collection point for recycling of electrical and electronic equipment. This
is to avoid environmental damage or personal injury due to uncontrolled waste
disposal. For more detailed information about recycling of this product contact the
local authorities or the authorized dealer.

11. Approval

Check the respective product page on the website of Highlite International (www.highlite.com) for an
available declaration of conformity.

©2022 Showtec