QFX Compact Light FX Set V1
V1
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 30276
MANUAL
ENGLISH
Ordercode: 30276
QFX Compact Light FX Set
Table of contents
Warning ............................................................................................................................................................................... 3
Unpacking Instructions ................................................................................................................................................. 3
Safety Instructions ......................................................................................................................................................... 4
Operating Determinations .......................................................................................................................................... 6
Laser safety for a Class 3B Laser Product ................................................................................................................. 6
Rigging ............................................................................................................................................................................ 7
Connection with the mains......................................................................................................................................... 8
Return Procedure .......................................................................................................................................................... 9
Claims .............................................................................................................................................................................. 9
Description of the device ...............................................................................................................................................10
Features ........................................................................................................................................................................10
Frontside........................................................................................................................................................................11
Backside .......................................................................................................................................................................11
Remote Control ...........................................................................................................................................................12
Footswitch ....................................................................................................................................................................12
Installation .........................................................................................................................................................................13
Set Up and Operation .....................................................................................................................................................13
Control Modes .............................................................................................................................................................14
One QFX Compact Light FX Set (Built-in programs) ..........................................................................................14
One QFX Compact Light FX Set (Sound-controlled) ........................................................................................14
One QFX Compact Light FX Set (Manual Mode) ..............................................................................................14
Multiple QFX Compact Light FX Sets (Master/Slave Mode) ............................................................................14
Multiple QFX Compact Light FX Sets (DMX Control) .........................................................................................15
Fixture Linking ...............................................................................................................................................................16
Data Cabling ...............................................................................................................................................................16
Control Panel ...............................................................................................................................................................17
Control Mode ..............................................................................................................................................................17
DMX Addressing ..........................................................................................................................................................17
Menu Overview ...........................................................................................................................................................18
Main Menu Options ....................................................................................................................................................19
1. Built-in Programs ...................................................................................................................................................19
1.1 PAR / Derby mode ............................................................................................................................................19
1.2 Laser mode .........................................................................................................................................................20
1.3 Flash mode .........................................................................................................................................................20
1.4 Mix mode ............................................................................................................................................................20
2. Sound-controlled .................................................................................................................................................20
2.1 PAR / Derby mode ............................................................................................................................................20
2.2 Laser mode .........................................................................................................................................................20
2.3 Flash mode .........................................................................................................................................................21
2.4 Mix mode ............................................................................................................................................................21
3. Manual Mode.......................................................................................................................................................21
4. DMX Mode ............................................................................................................................................................21
5. Master / Slave Mode ...........................................................................................................................................21
6. Settings ...................................................................................................................................................................22
DMX Channels .............................................................................................................................................................22
3 Channels ................................................................................................................................................................22
5 Channels ................................................................................................................................................................24
9 Channels ................................................................................................................................................................25
27 Channels ..............................................................................................................................................................26
1
Ordercode: 30276
QFX Compact Light FX Set
Maintenance ....................................................................................................................................................................28
Replacing the Fuse .....................................................................................................................................................28
Troubleshooting ...............................................................................................................................................................29
No Light .........................................................................................................................................................................29
No Response to DMX..................................................................................................................................................29
Product Specifications ....................................................................................................................................................31
Dimensions ........................................................................................................................................................................32
Notes ..................................................................................................................................................................................34
2
Ordercode: 30276
QFX Compact Light FX Set
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
QFX Compact light Fx Set
Carrying bag
Schuko to IEC power cable (5 m)
2 keys for the Interlock
Remote plug
Remote control
Footswitch
2 brackets, 3 screws (1 screw for stand)
Stand with carrying bag
User manual
3
Ordercode: 30276
QFX Compact Light FX Set
Safety Instructions
Every person involved with the installation, operation and maintenance of this device have to:
• be qualified
• follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never place any material over the lens.
• Never look directly into the light source.
• Never leave any cables lying around.
• Never aim the laser beam at people or animals!
• Never use the device during thunderstorms, unplug the device immediately.
• Never point a laser at aircraft, this is a federal offense.
• Never point unterminated laser beams into the sky.
• Never open the laser housing. The high laser power levels inside of the protective housing can start
fires, burn skin and will cause instant eye injury.
• Never expose the lens to direct sunlight, not even for a short period. This may damage the light
effect or even cause fire.
• Do not insert objects into air vents.
• Do not connect this device to a dimmerpack.
• Do not open the device and do not modify the device.
• Do not point lasers at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser
reflections can be hazardous.
• Do not expose the output optic (aperture) to cleaning chemicals.
• Do not use laser if the laser appears to be emitting only one or two beams.
• Do not use laser if housing is damaged or open, or if optics appear damaged in any way.
4
Ordercode: 30276
QFX Compact Light FX Set
• Do not operate laser without first reading and understanding all safety and technical data in this
manual. Never look into the laser aperture or laser beams.
• Do not switch the device on and off in short intervals, as this would reduce the device’s life.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Do not touch the device’s housing bare-handed during its operation (housing becomes hot).
• After set up and prior to public use, test laser to ensure proper function. Do not use the laser if any
defect is detected. Do not use, if the laser emits only one or two laser beams rather than
dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow
emission of higher laser levels.
• Only use device indoor, avoid contact with water or other liquids.
• Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always check the regulations when using a class 3B laser product.
• Always check and position the laser before anybody enters the room, when the laser is facing an
area with people.
• Always keep case closed while operating.
• Always allow free air space of at least 1 m around the unit for ventilation.
• Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power-cord by the plug. Never pull out the plug by tugging the power-cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power-cord is never crimped or damaged. Check the device and the power
cord from time to time.
• If the external cable is damaged, it has to be replaced by a qualified technician.
• If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to
cracks or deep scratches.
• If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
• If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
• Never attempt to bypass the thermostatic switch or fuses.
• For replacement use fuses of same type and rating only.
• The operation of a class 3B laser show laser is only allowed if the show is controlled by a skilled and
well-trained operator familiar with the data included in this manual.
• The user is responsible for correct positioning and operating of the QFX Compact Light FX Set. The
manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
• The laser will only work between 10-40ºC.
• After 3 hours working, you must shut off the laser and let the laser diode cool off for 30 minutes,
otherwise the laser could be damaged and the warranty becomes void.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
5
Ordercode: 30276
QFX Compact Light FX Set
CAUTION: AVOID EXPOSURE TO BEAM: Avoid direct eye contact with laser
light. Never intentionally expose your eyes or others to direct laser radiation.
Laser Classification
Class 3B
Cooling
Cooling fans and TE Cooling
Laser medium (Output)
wavelength 650 nm / Red; Output >150mW
wavelength 532 nm / Green; Output >50mW
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between light-output and the illuminated surface must be more than 1 meter.
● The maximum ambient temperature ta = 40°C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 30° C.
● If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Laser safety for a Class 3B Laser Product
Laser Light is different from any other light source with which you may be familiar with. The light from this
product can potentially cause instant eye injury if not set up and used properly.
Laser light is thousands of times more concentrated than light from any other kind of light source. This
concentration of light power can cause instant eye injuries, primarily by burning the retina (the light
sensitive portion at the back of the eye). Even if you cannot feel ”heat” from a laser beam, it can still
potentially injure or blind you or your audience.
Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries
can happen quicker than you can blink.
It is incorrect to think that because these laser products split the laser into hundreds of beams or the laser
beam is scanned out in high speed, that an individual laser beam is safe for eye exposure. This laser
product uses dozens of milliwatts of laser power (Class 3B levels internally). Many of the individual beams
are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This is not true. Nor, do the
laser beams always move. Since eye injuries can occur instantly, it is critical to prevent the possibility of
any direct eye exposure. According to the laser safety regulation, it is not legal to aim Class 3B lasers in
areas which people can get exposed. This is true even if it is aimed below people’s faces, such as on a
dance floor.
CAUTION! Only Laser Safety Officers who are officially certified by a regulatory body or authorized
training organization are allowed to use class 3B lasers in public. The Laser Safety Officer is responsible for
all aspects when using this laser, including following all locally applicable safety laws and regulations.
The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this laser.
Compliance Statement
Your QFX Compact Light FX Set laser has been designed to comply with FDA and IEC Standards for its
classification.
The QFX Compact Light FX Set is a Class 3B laser product.
Laser Safety and Compliance Information
The QFX Compact Light FX Set is manufactured to comply with the IEC 60825-1 and in accordance with
U.S. Food and Drug Administration (FDA) Standards Listed under FDA Document 21 CFR 1040 and
subsequent laser notices.
Product Classification and Manufacturing Label Identification
6
Ordercode: 30276
QFX Compact Light FX Set
This laser product is a Class 3B laser and has an interlocked
housing.
There are no user serviceable parts inside. Tampering or
removing warranty seals will void your products limited
warranty.
Combo label with the Product Model Number, Serial Number,
Date of Manufacturing, Laser Light Warning Label, Warranty
Void Label and Interlocked Housing Label.
According to FDA Regulations you should
operate this product as stated on the left.
The legal requirements for using laser entertainment products vary from country to country. The user is
responsible for the legal requirements at the location/country of use.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard
“For Safe Use of Lasers”, available from www.laserinstitute.org. Many local governments, corporations,
agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser
Display guidance can be obtained via the International Laser Display Association, www.laserist.org.
CAUTION: The use of corrective eye wear or optics for viewing at distances such as telescopes or
binoculars within a distance of 100mm may pose an eye hazard.
Proper Usage Safety and Compliance Information
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
7
Ordercode: 30276
QFX Compact Light FX Set
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Procedure:
● If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the projector, with the mounting-bracket, to the trussing system.
● The projector must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
a safety cable.
● When rigging, derigging or servicing the projector, always make sure that the area below the
installation is unavailable for any unauthorized persons.
The QFX Compact Light FX Set can be placed on a flat stage floor or mounted to any kind of truss with a
clamp.
Improper installation can cause serious injuries and damage of property !
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
Make sure that the device is always connected properly to the earth!
8
Ordercode: 30276
QFX Compact Light FX Set
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
9
Ordercode: 30276
QFX Compact Light FX Set
Description of the device
Features
The Showtec QFX Compact Light FX Set combines 2x LED PAR, 2x Derby, a Laser and a Strobe effect onto
a single control bar. The system is complete including a tripod stand, wireless footswitch, IR remote and
carrying bags to protect the set during transport.
Compact strong metal housing
Input Voltage: 100-240V 50/60Hz
Continues Power: 45W
Control mode: Built-in programs, Sound controlled, Manual mode, Master / Slave, DMX
Sound-controlled via built-in microphone
DMX-controlled via built-in microphone
DMX modes: 3, 5, 9, 27 Channels
Clear 4 Digits Red LED display for all settings
Power Connection: IEC in- & output
Data Connector: 3-pole XLR (In/Out)
Cooling: Convection (no fans) which eliminates the use of fans and noise
Working temperature: -10°C - 40°C
Fuse T1,5 AL / 250V
Safety eye
Dimensions: 1185 x 110 x 387 mm (LxWxH)
Weight: 6,6 kg
Included: 2 keys, Interlock test connector, wireless foot controller, remote control, 2 carrying bags,
IEC cable, stand
Safety eye
LED PAR
Lux@2m: 1205
Colors: RGB
LED: 6x3W 3-in-1
Current: 950mA
Beam angle: 24°
Derby
Colors: RGB
LED: 6x2W 3-in-1
Current: 600mA
Laser
Laser Class: 3B
Laser Safety: EN/IEC 60825-1 Ed 2, 2007-03
Laser Color: Red, Green
Laser Power: 200mW (150mW 650nm Red, 50mW 532nm Green)
Safety Features: Key switch, Interlock connector
The laser only works when the interlock connector is connected and the key switch is turned
Strobe
LED: 4x 1W White
Current: 300mA
Strobe: 0 – 18Hz
Footswitch
Frequency: 433mHz
Range: 30m
Tripod stand
Height: 1,5 – 2,5m
Footspace: 0,9m
10
Ordercode: 30276
QFX Compact Light FX Set
Frontside
Fig. 01
Backside
Fig. 02
01) Adjustment screw
02) Mounting bracket
03) Built-in microphone
04) IR sensor
05) Antenna for footswitch
06) 1W white LED
07) Laser
08) Safety eye
09) LED PAR
10) Derby
11) Ground / earth connection
12) IEC Power connector (OUT)
13) IEC Power connector (IN), Fuse T1,5AL / 250V
14) 3-pin DMX signal connector OUT
15) 3-pin DMX signal connector IN
16) Key switch
17) Remote switch
18) Sound sensitivity
19) Mode button
20) Up button
21) Down button
22) Enter button
23) LCD display
24) IR sensor
11
Ordercode: 30276
QFX Compact Light FX Set
Button
Function
Description On / Off
Power on / off
Auto Mode
Set the auto mode from (AM01 - AM03)
Sound Mode
Set the sound mode from (SN01 - SN03)
PAR Auto Mode
Set the PAR mode from (AP01 - AP18)
Laser Auto Mode
Set the laser mode (AL01 – AL06)
Flash Auto Mode
Set the flash mode (AF01 – AF10)
Auto / Sound switching
Switch between auto / sound ( )
Pause
pause
Color changing
Select the PAR color
Numeric keys
Program speed adjustment (1-9)
Button
Function
Description
Auto
Auto Mode
Set the auto mode from (AM01 - AM03)
Music
Sound Mode
Set the sound mode from (SM01 - SM03)
Color
Color changing
Select the PAR color
Blackout
Blackout
Blackout
Remote Control
Attention:
Any control or setting with the remote control will be saved, until the system is rebooted.
Footswitch
12
Ordercode: 30276
QFX Compact Light FX Set
They should be kept with the QFX Compact Light FX Set laser !!!
The following safety precautions should be followed:
• The keys should be put into the lock of your QFX Compact Light FX Set laser.
Warning
Installation
Remove all packing materials from the QFX Compact Light FX Set. Check if all foam and plastic padding
is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be music-controlled by its built-in
microphone.
The Interlock plug/remote plug and safety keys are included in the box.
The interlock is the “included-in-the-box” successor for the optional remote interlock (51316)
Exclusion of liability
Be aware that in some countries, there are additional regulations, regarding the use of laser devices.
Therefore, we strongly advise you to verify your national laws with your authorities: We do not take any
responsibility for eventual discrepancies, changes or adaptions regarding lawful use of laser devices.
13
Ordercode: 30276
QFX Compact Light FX Set
There are 5 modes:
Built-in programs
Sound-controlled
Manual Mode
Master / Slave
DMX512
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
Fig. 03
Control Modes
One QFX Compact Light FX Set (Built-in programs)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the QFX Compact Light FX Set is not connected by a DMX-cable, it functions as a stand-alone
device.
05) Please see page 19 and 20 for more information about the Built-in auto programs.
One QFX Compact Light FX Set (Sound-controlled)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the QFX Compact Light FX Set is not connected with a DMX-cable, it functions as a stand-
alone device.
05) Please see page 20 and 21 for more information about the Sound-controlled mode.
One QFX Compact Light FX Set (Manual Mode)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the QFX Compact Light FX Set is not connected with a DMX-cable, it functions as a stand-
alone device.
05) Please see page 21 for more information about the Manual Mode.
Multiple QFX Compact Light FX Sets (Master/Slave Mode)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the QFX Compact Light FX Sets.
05) Link the units as shown in Fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on page 19, 20 and 21 (Built-in or Soundcontrolled). This means on the master device you can set your desired operation Mode and all slave
devices will react the same as the master device.
Multiple QFX Compact Light FX Sets Master / Slave Set Up
14
Ordercode: 30276
QFX Compact Light FX Set
Fig. 04
Multiple QFX Compact Light FX Sets (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the QFX Compact Light FX Sets and other devices.
05) Link the units as shown in Fig. 04, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple QFX Compact Light FX Sets DMX Set Up
15
Note: Link all cables before connecting electric power
Ordercode: 30276
QFX Compact Light FX Set
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio Certified DMX Data Cables
• DAP Audio cable for all-round use. bal. XLR/M 3 p. > XLR/F 3 p.
Ordercode FL01150 (1,5m.), FL013 (3m.), FL016 (6m.), FL0110 (10m.), FL0115 (15m.), FL0120 (20m.).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5m.), FL713 (3m.), FL716 (6m.), FL7110 (10m.).
16
Ordercode: 30276
QFX Compact Light FX Set
A) LED display
B) MODE button
C) UP button
D) DOWN button
E) ENTER button
Fig. 05
Control Panel
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller (when you select the DMX address and save it,
the controller will display the saved DMX address the next time).
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the QFX Compact Light FX Set will respond to the controller.
Please note when you use the controller, the unit has 27 channels.
When using multiple QFX Compact Light FX Sets, make sure you set the DMX addresses right.
Therefore, the DMX address of the first QFX Compact Light FX Sets should be 1(001); the DMX address of
the second QFX Compact Light FX Set should be 1+27=28 (28); the DMX address of the third QFX
Compact Light FX Set should be 28+27=55 (55), etc.
Please, be sure that you do not have any overlapping channels in order to control each QFX Compact
Light FX Set correctly.
If two or more QFX Compact Light FX Sets are addressed similarly, they will work similarly.
Controlling:
After having addressed all QFX Compact Light FX Set fixtures, you may now start operating these via your
lighting controller.
Note: After switching on, the QFX Compact Light FX Set will automatically detect whether DMX-512 data
is received or not. If there is no data received at the DMX-input, the ”LED” on the control panel will not
flash.
The problem may be:
• The XLR cable from the controller is not connected with the input of the QFX Compact Light FX Set.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
17
Ordercode: 30276
QFX Compact Light FX Set
Menu Overview
18
Ordercode: 30276
QFX Compact Light FX Set
Built-in Programs
Sound-controlled
Manual Mode
DMX Mode
Master / Slave Mode
Settings
The QFX Compact Light FX Set will only show its version number at start-up !
PAR / Derby mode
Laser mode
Flash mode
Mix mode
Main Menu Options
1. Built-in Programs
With this menu you can you can set the built-in programs.
01) Press the MODE button on the device, until the display shows .
02) Press the ENTER button to open this menu.
03) You can use the Up / Down buttons to scroll through the 4 built-in programs.
1.1 PAR / Derby mode
01) Use the Up / Down buttons to choose a mode .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the PAR / Derby mode from .
04) You can use the ENTER button to change the settings.
05) Use the Up / Down buttons to change the strobe speed from .
06) You can use the ENTER button to change the settings.
07) Use the Up / Down buttons to change the motor speed from .
19
Ordercode: 30276
QFX Compact Light FX Set
PAR / Derby mode
Laser mode
Flash mode
Mix mode
1.2 Laser mode
01) Use the Up / Down buttons to choose a mode .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Laser mode from .
04) You can use the ENTER button to change the settings.
05) Use the Up / Down buttons to change the strobe speed from .
06) You can use the ENTER button to change the settings.
07) Use the Up / Down buttons to change the motor speed from .
1.3 Flash mode
01) Use the Up / Down buttons to choose a mode .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Flash mode from .
04) You can use the ENTER button to change the settings.
05) Use the Up / Down buttons to change the strobe speed from .
1.4 Mix mode
01) Use the Up / Down buttons to choose a mode .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Mix mode from .
04) You can use the ENTER button to change the settings.
05) Use the Up / Down buttons to change the strobe speed from .
2. Sound-controlled
With this menu you can you can set the device to sound-control.
01) Press the MODE button on the device, until the display shows .
02) Press the ENTER button to open this menu.
03) You can use the Up / Down buttons to scroll through the 4 sound-controlled programs.
2.1 PAR / Derby mode
01) Use the Up / Down buttons to choose .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the PAR / Derby mode from .
2.2 Laser mode
01) Use the Up / Down buttons to choose .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Laser mode from .
20
Ordercode: 30276
QFX Compact Light FX Set
Set the value of the red LEDs (000-255).
Set the value of the green LEDs (000-255).
Set the value of the blue LEDs (000-255).
Set the strobe speed (00-99).
The QFX Compact Light Set has 4 different DMX modes.
Set the address from d001-d510 (03CH).
Set the address from d001-d508 (05CH).
Set the address from d001-d504 (09CH).
Set the address from d001-d486 (27CH).
2.3 Flash mode
01) Use the Up / Down buttons to choose .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Flash mode from .
2.4 Mix mode
01) Use the Up / Down buttons to choose .
02) You can use the ENTER button to change the settings.
03) Use the Up / Down buttons to change the Mix mode from .
3. Manual Mode
With this menu you can you can manually set a desired color.
01) Press the MODE button on the device, until the display shows .
02) Press the ENTER button to open the menu.
03) You can use the ENTER button to scroll through the 3 color options and set the speed.
04) Use the Up / Down buttons to change the values.
You can combine Red, Green and Blue to create an infinite range of colors (000-255).
4. DMX Mode
With this menu you can you can select the DMX mode, and set the DMX address.
01) Press the MODE button on the device, until the display shows .
02) Press the ENTER button to open the menu.
03) Press the ENTER button to open this menu.
04) You can use the Up / Down buttons to scroll through the 4 programs.
05) You can use the ENTER button to select a DMX mode, and set the DMX address.
06) Use the Up / Down buttons to change the values.
5. Master / Slave Mode
01) Use the Up / Down buttons to choose a mode .
02) You can use the ENTER button to set the QFX Compact Light FX Set to .
21
Ordercode: 30276
QFX Compact Light FX Set
Machine Position Setting
Display On / Off
Test Mode
Factory Reset
Wireless Pedal On / Off
Channel 1 – Built-in Programs (CH2 must be set between 001-255 )
0-9
Blackout
10-31
Auto PAR
32-65
Auto Laser
66-95
Auto Flash LED
96-127
Auto MIX
128-159
Sound PAR
160-191
Sound Laser
192-223
Sound Flash LED
223-255
Sound MIX
Channel 2 – Auto PAR (CH1 must be set between 010-031 )
0
Blackout
1-9
AP01
10-19
AP02
20-29
AP03
30-39
AP04
40-49
AP05
50-59
AP06
60-69
AP07
70-79
AP08
80-89
AP09
90-99
AP10
6. Settings
With this menu you can you can enter the settings.
01) Press the MODE button on the device, until the display shows .
02) Press the ENTER button to open this menu.
03) You can use the Up / Down buttons to scroll through the 5 settings.
04) You can use the ENTER button to change the machine position settings .
05) Use the Up / Down buttons to change the PAR and Derby order.
The PAR and Derby can be changed in every order , , , .
06) You can use the ENTER button to select the display on / off function .
07) Use the Up / Down buttons to set the display on / off function .
If switched on, the display wil turn off after 30sec.
08) You can use the ENTER button to select the test mode .
09) You can use the ENTER button to confirm.
10) You can use the ENTER button to select the factory reset .
11) You can use the ENTER button to confirm.
12) You can use the ENTER button to select the wireless pedal on / off function .
13) Use the Up / Down buttons to set the wireless pedal on / off function .
DMX Channels
3 Channels
22
Ordercode: 30276
QFX Compact Light FX Set
100-109
AP11
110-119
AP12
120-129
AP13
130-139
AP14
140-149
AP15
150-159
AP16
160-169
AP17
170-255
AP18
Channel 2 – Auto Laser (CH1 must be set between 032-065 )
0-39
AL01
40-79
AL02
80-119
AL03
120-139
AL04
140-159
AL05
160-255
AL06
Channel 2 – Auto Flash LED (CH1 must be set between 066-095 )
0-14
AF01
15-29
AF02
30-44
AF03
45-59
AF04
60-74
AF05
75-89
AF06
90-104
AF07
105-119
AF08
120-134
AF09
135-255
AF10
Channel 2 – Auto MIX (CH1 must be set between 096-127 )
0-19
AM01
20-39
AM02
40-255
AM03
Channel 2 – Sound PAR (CH1 must be set between 128-159 )
0-9
SP01
10-19
SP02
20-29
SP03
30-39
SP04
40-49
SP05
50-59
SP06
60-69
SP07
70-79
SP08
80-89
SP09
90-99
SP10
100-109
SP11
110-119
SP12
120-129
SP13
130-139
SP14
140-149
SP15
150-159
SP16
160-169
SP17
170-255
SP18
23
Ordercode: 30276
QFX Compact Light FX Set
Channel 2 – Sound Laser (CH1 must be set between 160-191 )
0-39
SL01
40-79
SL02
80-119
SL03
120-139
SL04
140-159
SL05
160-255
SL06
Channel 2 – Sound Flash LED (CH1 must be set between 192-223 )
0-14
SF01
15-29
SF02
30-44
SF03
45-59
SF04
60-74
SF05
75-89
SF06
90-104
SF07
105-119
SF08
120-134
SF09
135-255
SF10
Channel 2 – Sound MIX (CH1 must be set between 224-255 )
0-19
SM01
20-39
SM02
40-255
SM03
Channel 3 – Program Speed (CH1 must be set between 010-255, CH2 must be set between 001-255 )
0-255
From slow to fast, 0 is the slowest, 255 is the fastest
Channel 1 – PAR and Derby Red Dimmer intensity (CH4 must be set between 001-255 )
0-255
Red from 0 – 100%
Channel 2 – PAR and Derby Green Dimmer intensity (CH4 must be set between 001-255 )
0-255
Green from 0 – 100%
Channel 3 – PAR and Derby Blue Dimmer intensity (CH4 must be set between 001-255 )
0-255
Blue from 0 – 100%
Channel 4 – PAR and Derby Dimmer intensity (CH1, CH2 or CH3 must be set between 001-255 )
0-191
Brightnes of all lights
192-200
Sound strobe
201-249
Strobe effect, from slow to fast (0-18Hz)
250-255
Full on
Channel 5 – Derby LED Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
5 Channels
24
Ordercode: 30276
QFX Compact Light FX Set
Channel 1 – PAR and Derby Red Dimmer intensity (CH4 must be set between 001-255 )
0-255
Red from 0 – 100%
Channel 2 – PAR and Derby Green Dimmer intensity (CH4 must be set between 001-255 )
0-255
Green from 0 – 100%
Channel 3 – PAR and Derby Blue Dimmer intensity (CH4 must be set between 001-255 )
0-255
Blue from 0 – 100%
Channel 4 – PAR and Derby Dimmer intensity (CH1, CH2 or CH3 must be set between 001-255 )
0-191
Brightnes of all lights
192-200
Sound strobe
201-249
Strobe effect, from slow to fast (0-18Hz)
250-255
Full on
Channel 5 – Derby LED Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
Channel 6 – Red Laser Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 7 – Red Laser Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 8 – Laser Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
Channel 9 – 4 pcs Strobe LED
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
9 Channels
25
Ordercode: 30276
QFX Compact Light FX Set
Channel 1 – Derby (nr.1) Red Dimmer intensity
0-255
Red from 0 – 100%
Channel 2 – Derby (nr.1) Green Dimmer intensity
0-255
Green from 0 – 100%
Channel 3 – Derby (nr.1) Blue Dimmer intensity
0-255
Blue from 0 – 100%
Channel 4 – Derby (nr.1) Speed
0-9
Blackout
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 5 – Derby (nr.1) Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
Channel 6 – PAR (nr.2) Red Dimmer intensity
0-255
Red from 0 – 100%
Channel 7 – PAR (nr.2) Derby Green Dimmer intensity
0-255
Green from 0 – 100%
Channel 8 – PAR nr.2 Derby Blue Dimmer intensity
0-255
Blue from 0 – 100%
Channel 9 – PAR (nr.2) Speed
0-9
Blackout
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 10 – PAR (nr.2)
0-255
Keep the channel
Channel 11 – PAR (nr.3) Red Dimmer intensity
0-255
Red from 0 – 100%
Channel 12 – PAR (nr.3) Derby Green Dimmer intensity
0-255
Green from 0 – 100%
Channel 13 – PAR (nr.3) Derby Blue Dimmer intensity
0-255
Blue from 0 – 100%
Channel 14 – PAR (nr.3) Speed
0-9
Blackout
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 15 – PAR (nr.3)
0-255
Keep the channel
Channel 16 – Derby (nr.4) Red Dimmer intensity
0-255
Red from 0 – 100%
27 Channels
26
Ordercode: 30276
QFX Compact Light FX Set
Channel 17 – Derby (nr.4) Green Dimmer intensity
0-255
Green from 0 – 100%
Channel 18 – Derby (nr.4) Blue Dimmer intensity
0-255
Blue from 0 – 100%
Channel 19 – Derby (nr.4) Speed
0-9
Blackout
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 20 – Derby (nr.4) Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
Channel 21 – Red Laser Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 22 – Green Laser Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 23 – Laser Motor rotating speed
0-4
Stop
5-127
Rotate clockwise, from slow to fast
128-133
Stop
134-255
Rotate counterclockwise, from slow to fast
Channel 24 – Strobe LED (nr.1) Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 25 – Strobe LED (nr.2) Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 26 – Strobe LED (nr.3) Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
Channel 27 – Strobe LED (nr.4) Dimmer intensity
0-4
Blackout
5-9
Full on
10-255
Strobe effect, from slow to fast (0-18Hz)
27
Ordercode: 30276
QFX Compact Light FX Set
Maintenance
The Showtec QFX Compact Light FX Set requires almost no maintenance. However, you should keep the
unit clean. Otherwise, the fixture’s light-output will be significantly reduced.
Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass
panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents. The front glass panel will
require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light-output very quickly.
Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below.
01) Unplug the unit from electric power source.
02) Insert a screwdriver into the slot in the fuse cover. Gently pry up the fuse cover. The fuse will come
out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to
use a fuse of the same type and specification. See the product specification label for details.
28
Ordercode: 30276
QFX Compact Light FX Set
Troubleshooting
No Light
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
If the light effect does not operate properly, refer servicing to a technician.
Response: Suspect three potential problem areas as: the power supply, the laser, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The laser. Return the QFX Compact Light FX Set to your Showtec dealer.
03) The fuse. Replace the fuse. See page 28 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the QFX Compact Light FX
Set, as this may damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card
malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
29
Ordercode: 30276
QFX Compact Light FX Set
Problem
Probable cause(s)
Remedy
One or more
fixtures are
completely dead.
No power to the fixture.
● Check that power is switched on and
cables are plugged in.
Primary fuse blown..
● Replace fuse.
Fixtures reset
correctly, but all
respond erratically
or not at all to the
controller.
The controller is not connected.
● Connect controller.
3-pin XLR Out of the controller does
not match XLR Out of the first fixture
on the link (i.e. signal is reversed).
● Install a phase reversing cable between
the controller and the first fixture on the
link.
Fixtures reset
correctly, but some
respond erratically
or not at all to the
controller.
Poor data quality
● Check data quality. If much lower than
100 percent, the problem may be a
bad data link connection, poor quality
or broken cables, missing termination
plug, or a defective fixture disturbing
the link.
Bad data link connection
● Inspect connections and cables.
Correct poor connections. Repair or
replace damaged cables.
Data link not terminated with 120
Ohm termination plug.
● Insert termination plug in output jack of
the last fixture on the link.
Incorrect addressing of the fixtures.
● Check address setting.
One of the fixtures is defective and
disturbs data transmission on the
link.
● Bypass one fixture at a time until normal
operation is regained: unplug both
connectors and connect them directly
together.
● Have the defective fixture serviced by a
qualified technician.
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed).
● Install a phase-reversing cable between
the fixtures or swap pin 2 and 3 in the
fixture, that behaves erratically.
Shutter closes
suddenly
The laser diode has lost its index
position and the fixture is resetting
the effect.
● Contact a technician for servicing the
problem persists.
No light or laser
cuts out
intermittently
Fixture is too hot.
● Allow fixture to cool.
● Make sure air vents at control panel
and front lens are not blocked.
● Turn up the air conditioning .
LEDs damaged
● Disconnect fixture and return to your
dealer.
The power supply settings do not
match local AC voltage and
frequency.
● Disconnect fixture. Check settings and
correct if necessary.
30
Ordercode: 30276
QFX Compact Light FX Set
Model:
QFX Compact Light FX Set
Input Voltage:
AC 100-240V, 50/60Hz
Continuous Power:
45 Watt
Fuse:
T1,5A / 250V
Dimensions:
1185 x 110 x 387 mm (LxWxH)
Weight:
6,6 kg
Operation and Programming:
Set Up and Addressing:
Red 4 Digits LED display for all settings
Power Connection:
IEC in- & output
DMX modes:
3, 5, 9, 27 Channels
Signal input:
3-pin DMX signal connector IN
Signal output:
3-pin DMX signal connector OUT
Signal pin OUT:
pin 1 earth, pin 2 (-), pin 3 (+)
Electro-mechanical effects:
Control modes:
Built-in programs, Sound controlled, Manual mode,
Master / Slave, DMX
Sound-control:
via built-in microphone
Housing:
Compact strong metal housing with safety eye
IP Rating:
IP20
Cooling:
Convection (no fans) which eliminates the use of fans and
noise
Working temperature:
-10°C - 40°C
Included:
2 keys, Interlock test connector, wireless foot controller,
remote control, 2 carrying bags, IEC cable, stand
LED PAR:
Lux@2m:
1205
Colors:
RGB
LED:
6x3W 3-in-1
Current:
950mA
Beam angle:
24°
Derby:
Colors:
RGB
LED:
6x2W 3-in-1
Current:
600mA
Laser:
Laser Class:
3B
Laser Safety:
EN/IEC 60825-1 Ed 2, 2007-03
Laser Color:
Red, Green
Laser Power:
200mW (150mW 650nm Red, 50mW 532nm Green)
Safety Features:
Key switch, Interlock connector
Strobe:
LED:
4x 1W White
Current:
300mA
Strobe:
0 – 18Hz
Footswitch:
Frequency:
433mHz
Range:
30m
Tripod stand:
Height:
1,5 – 2,5m
Footspace:
0,9m
Max. ambient temperature ta: 40°C
Max. housing temperature ta: 80°C
Product Specifications
31
Ordercode: 30276
QFX Compact Light FX Set
Minimum distance:
Minimum distance from flammable surfaces:
1 m
Minimum distance to lighted object:
1 m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: service@highlite.nl
Dimensions
32
Ordercode: 30276
QFX Compact Light FX Set
33
Ordercode: 30276
QFX Compact Light FX Set
Notes
34
©2015 Showtec
Loading...