Showline SL Punchlite 220 User Manual

SL PUNCHLITE 220

Showline Offices

Showline - Da llas

10911 Petal Street

Dallas, TX 75238

Showline - Auckland

19-21 Kawana Street

Northcote, Auckland 0627

New Zealand U.S.A

Tel: [phone]

Fax: [phone]

Showline - Eu rope

Marssteden 152

Enschede 7547 TD

The Netherlands

Tel: [phone]

Fax: [phone]

Unit C, 14/F, Roxy Industrial Centre

Tel: [phone]

Fax: [phone]

Showline - Asia

No. 41-49 Kwai Cheong Road

Kwai Chung, N.T., Hong Kong

Tel: [phone]

Fax: [phone]

Website:

www.philips.com/showline

The material in this manual is for information purposes only and is subject to change without notice. Showline assumes
no responsiblitity for any errors or omissions which may appear in this manual. For comments and suggestions regarding
corrections and/or updates to this manual, please visit the Showline website at or contact yourwww.philips.com/showline
nearest Showline office.

Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.

Document Number: SL PUNCHLITE 220 User Manual

Version a s of: 24th Sep, 2015 Rev1.0

SL PUNCHLITE 220 Installation & User’s Manual

2015 Philips Group. All rights reserved.

IMPORTANT INOFRMATION

Warnings and Notices

When using electrical equipment, basic safety precautions should a lways b e follo wed inc ludin g the fol lowin g:

READ AND F OLLOW ALL SA FETY INSTRUCTIONS.

Do not mount near gas or electric heaters.

Equipment should be mounted in locations and at heights where i t will not read ily be subject
to tampering by unauthorized personnel.

The use of accessory equipment not recommended by the manufac turer may cau se an unsafe
condition.

Do not use this equipment for other than intended use.

Refer service to qualified personnel.

Installat ion & User’s Manu alSL PUNCHLIT E 220

WARNING: You must have access to a mains circuit breake r or other powe r disconnect device
before installing any wiring. BE sure that power is disconnec ted by removi ng fuses or turning the
mains circuit breaker off befor e installation. Installing the device with power on may expose you
to dangerous voltages and damage the device. A qualified el ectrician must perform this installation.

WARNING: Re fer to National Electrical Code and local codes fo r cable specifications.
Failure to use proper cable can result in damage to equipment or da nger to perso nnel.

WARNING: This equipment is intended for inst allation in a ccordance with the National Electric
Code and local regulations. It is also intended for installat ion in indoor a pplications only. Before
any electrical work is performed, disconnect power at the cir cuit breake r or remove the fuse to
avoid shock or damage to the control. It is recommended that a qual ified elect rician perform this
installation.

Additional Resources for DMX512

For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:

USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org

Showline Limited Two-Year Warranty

Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the
date of delivery. A copy of the Showline two-year limited warranty containing specific terms and conditions can be
obtained by contacting your local Showline office.

TABLE OF CONTENTS

Showline Offices Inside Front Cover

IMPORTANT INFORMATION

Warnings and Notices
Additional Resources for DMX512
Showline Limited Two-Year Warranty

TABLE OF CONTENTS
PREFACE

About this Manual
Included Items

SL PUNCHLITE 220 OVERVIEW

SL PUNCHLITE 220 Components

INSTALLATION AND SET UP

Connecting Power

Connecting SL PUNCHLITE 220 to AC Power
Connecting to the DMX512 Network
Mounting Luminaire

Truss / Hanging Applications

Floor Mounting

OPERATION AND PROGRAMMING

LCD Display and Menu System
LCD Display and Menu System Operation

SL PUNCHLITE 220 Menu Tree

Quick Selection Buttons

Edit a Preset Button

Edit a Chase Button

DMX Address Button
Dimming Curve Selection
Master / Slave Operational Mode

DMX CONTROL

SL PUNCHLITE 220 DMX Mapping

Simple 8-Bit Mode

Simple 8-Bit Group Mode

RGBW 8-Bit Mode

RGBW 8-Bit Group Mode

RGBW 16-Bit Mode

RGBW 16-Bit Group Mode

HSIC Mode

HSIC Group Mode
DMX Timing Channel Detail

RDM PARAMETER IDs

SL PUNCHLITE 220 RDM Parameter IDs

CLEANING AND CARE

Special Cleaning and Care Instructions
Front Lens Cleaning
Service and Maintenance

TECHNICAL SPECIFICATIONS

Operational Specifications
Luminaire Dimensions

1
1
1

3
3

4

6
6
7

8

8

8

9

10

11

13

13
13
13

14
15

16

16

17

18

22

23

27

28

29
30

36

39

39

39

40
41

2

Table o f conte nts

PREFACE

1. About this Manual

The document provides install ation and operation instructions for the following products:

SL PUNCHLITE 220 Luminaire

Please read all instructions before installing or using thi s product. Retain this manual for future reference.
Additional product information and descriptions may be fo und on the prod uct specification sheet.

Note: The SL PUNCHLITE 220 luminaire works from 100 to 240 VAC (auto-ranging).

2. Included Items

Each SL PUNCHLITE 220 luminaire includes the following items:

SL PUNCHLITE 220 Luminaire

Installat ion & User’s Manu alSL PUNCHLIT E 220

Quick Start Guide

SL PUNCHLITE 220 Luminaire

US Market

AC In put cab le (175 0mm)
(Fo r US, Can ada and L atin Ame rica ma rket on ly)

AC Ou tput ca ble (10 00mm)
(Fo r US, Can ada and L atin Ame rica ma rket on ly)

DMX I nput ca ble (10 00mm)

DMX O utput c able (1 000mm )

International M arket

AC In put cab le (150 0mm)
(Fo r Inter natio nal mar ket onl y)

AC Ou tput ca ble (10 00mm)
(Fo r Inter natio nal mar ket onl y)

DMX I nput ca ble (10 00mm)

DMX O utput c able (1 000mm )

Cables

About t his Man ual

3

Installat ion & User’s Manu al

SL PUNCHLITE 220 OVERVIEW

1.

SL PUNCHLITE 220 COMPONENTS

SL PUNCHLIT E 220

Common Luminaire Components

Front of luminaire

High Power LEDs

Figure 1: SL PUNCHLIT E 220 Common Co mponents

LCD Display / Menu System

Yoke

LCD Display / Menu System

Safety Cab le
Anchor Poi nt

DMX512 / RDM Input DMX512 / RDM Output

AC Input

Rear of luminaire

Tilt Knob

AC Output

Edit a Preset

Home (menu settings)

LCD Display

LEFT Arrow Button

RIGHT Arrow Button

NOTE: The menu rotates with the orientation of
luminaire and the menu buttons are always in
the same position (with rotation of menu)

SL PUNCHLITE 220

To rotate the menu 180 degrees from the current orientation,
press and hold the two center buttons for 2 seconds.

Edit a Chase

DMX512 Addressing

Return to Main Screen

DOWN Arrow Button

UP Arrow Button

CHECK MARK (Accept) Button

Figure 2: LCD Display & Menu System

Note: For Menu operation and programming details, refer to "LCD Display and Menu System" on page 9.

4

SL PUNC HLITE 2 20 Over view

INSTALLATION AND SET UP

1. Power Requirements

The SL PU NCHLITE 220 Luminaire operates on AC input voltages from 100 to 240 VAC.

WARNING! The SL PUNCHLITE 220 luminaire does not have an ON/OFF switch. Always disconnect power input cable

to completely remove power from the luminaire when not in use.

AC Power Operation

When connected to an AC source, the luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply. Each luminaire can draw up to 220 Watts.

WARNING! Maximum amount of fixtures that may be daisy-chained is (A) 4 luminaires 100 ~ 120VAC or (B) 10 luminaires
230 ~ 240VAC (10 Amps).

Table 1: SL PUNCHLITE 220Voltage (VAC) vs. Current*

Voltage (AC) Voltage (AC)

100

110

120

130

140

150

160

170 1.29

Total Current (A) Total Current (A)

2.00

1.83

1.57

Installat ion & User’s Manu alSL PUNCHLIT E 220

180

190 1.16

200

210

220

230

240

1.222.20

1.10

1.041.69

1.00

0.961.46

0.921.37

Note: For wiring of AC input connector, refer to "Connecting SL PUNCHLITE 220 to AC Power" on page 6.

2. Connecting Power

luminaires can be powered in one of two ways:

Direct connection to an AC power source using an AC input cable. For wiring of the AC input connector, refer to

"Connecting SL PUNCHLITE 220 to AC Power" on page 6.

Connection from the AC output of another SL PUNCHLI TE 220. When using this method, it is very important not
to connect any other type of equipment device.

WARNING! Only connect other SL PUNCHLITE 220 luminaires to the AC Output (Thru) connector of an
SL PUNCHLITE 220 luminaire.

Insta llati on and Se t Up

5

Installat ion & User’s Manu al

Connecting SL PUNCHLITE 220 to AC Power

Table 2 describes how to connect power to your SL PUNCHLITE 220. Field wiring of the SL PUNCHLITE 220 LED

Luminaire is straight-forward. A total of 3 wires/conductors need to be brought to the luminaire.

The following wiring scheme is required:

Table 2: SL PUNCHLITE 220AC Input/Output Connections

Wire Color Purpose

Brown

Blue Neut ral

Green/Yell ow

Main/Lin e(1 00 to 240VAC)

Ground (Ea rth )

SL PUNCHLIT E 220

AC Input

AC Output

Luminaire

Figure 3: SL PUNCHLITE 220 AC Input & Output Connections

Connecting SL PUNCHLITE 220 to AC Power

6

Installat ion & User’s Manu alSL PUNCHLIT E 220

3. Connecting to the DMX512 Network

Basic DMX512 installation consists of connecting multiple SL PUNCHLITE 220s together (up to 32 luminaires) in

"daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX connector

on the first SL PUNCHLITE 220. Another cable runs from the other DMX connector on the first luminaire to a DMX
connector on the next SL PUNCHLITE 220 (or DMX512 device to be controlled).

Luminaire

DMX512 / RDM
Input Connector

DMX512 / RDM

THRU Connector

Figure 4: SL PUNCHLITE 220 DMX512 Input / Output Connections

Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on

page 1 "DMX CONTROL" on page 16. For SL PUNCHLITE 220 DMX Mapping, refer to .

DMX512

(from console or
control device)

DMX512 (out from first

to second luminaire)

DMX512

luminaire or DMX512 controlled

(out to the next

device)

DMX512 Conections

DMX512 S ign al

Common ( Dra in)

DMX512 -

DMX512 +

Note: Re mai nin g pins on each con nec tor are not used .

XLR Pin

1

2

3

Color

Black

White

Red

Figure 5: SL PUNCHLITE 220- DMX512 Connections

Conne cting t o the DMX 512 Net work

7

Installat ion & User’s Manu al

4. Mounting Luminaire

Truss / Hanging Applications

The SL PUNCHLITE 220 is provided with the ability to hang via truss hooks, clamps, etc. (sold separately). Simply
attach hook, clamp, etc. to the SL PUNCHLITE 220 yoke in the provided M12 holes. It is recommended
(and may be required by local and national safety codes) to use and install a safety cable (sold separately) as illustrated in
Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire to allow proper, uninterrupted
airflow for cooling and movement. Refer to for spacing (dimensional) requirements."Luminaire Dimensions" on page 36

Note: Mounting hooks, clamps, safety cables, etc. are sold separately or by others. For mounting accessories
available for this product, refer to "Accessories" on page 3.

Truss Hook or Clamp
(sold separately)

SL PUNCHLIT E 220

Safety Cable Anchor Point

Figure 6: Mounting the Fixture - Hanging Applications

Floor Mounting

The SL PUNCHLITE 220 is designed to sit directly on its split yoke assembly in a floor installation application.
When used in this type of application, be sure to leave enough space around the luminaire to allow proper, uninterrupted

airflow for cooling and movement.

8

Mount ing Lum inair e

OPERATION AND PROGRAMMING

1. LCD Display and Menu System

SL PUNCHLITE 220

The SL PUNCHLITE 220’s LCD Display and Menu System provides local control for accessing
the following fixture’s settings:

Presets (Standard and User Defined)

Color Filter

Effects (Chases - preloaded and user defined)

Strobe / Timing

Settings

Lock Fixture (to prevent changes)

Password

Status

Installat ion & User’s Manu alSL PUNCHLIT E 220

Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. For
SL PUNCHLITE 220 menu structure, see . "SL PUNCHLITE 220 Menu Tree" on page 11

Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.

Edit a Preset

Home (menu settings)

LCD Display

LEFT Arrow Button

RIGHT Arrow Button

SL PUNCHLITE 220

Edit a Chase

DMX512 Addressing

Return to Main Screen

DOWN Arrow Button

UP Arrow Button

OK (Check Mark) Button

NOTE: Menu rotates with orientation of Luminaire and
menu buttons are always in the same position (with
rotation of menu)

Figure 7: LCD Display and Menu System

To rotate menu 180 degrees manually from current
orientation, press and hold the two center buttons for 2
seconds.

OPERA TION AN D PROGR AMMIN G

9

Installat ion & User’s Manu al

2. LCD Display and Menu System Operation

The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and make changes to
the menu items. When the desired menu item is reached, press the desired Menu Button to display the menu options
and to navigate and configure the menu options as required.

To navigate and access menu settings/selections:

Step 1. Make sure luminaire is powered and turned on.
Step 2. Press the desired button (as shown in Figure 8) to access menu categories.
Step 3. Use UP | DOWN | LEFT | RIGHT arrow buttons to navigate through the various options and settings.
Step 4. Make changes as desired.

Press CHECK MARK (OK) button to accept changes.

SL PUNCHLIT E 220

Edit a Preset

Home (menu settings)

LCD Display

LEFT Arrow Button

RIGHT Arrow Button

NOTE: Menu rotates with orientation of Luminaire and
menu buttons are always in the same position (with
rotation of menu)

Figure 8: LCD Display and Menu System

Edit a Chase

DMX512 Addressing

Return to Main Screen

SL PUNCHLITE 220

DOWN Arrow Button

UP Arrow Button

OK (Check Mark) Button

To rotate menu 180 degrees manually from current
orientation, press and hold the two center buttons for 2
seconds.

LCD Dis play an d Menu Sy stem Op erati on

10

3. SL PUNCHLITE 220 Menu Tree

Installat ion & User’s Manu alSL PUNCHLIT E 220

MAIN MENU

Preset

Color Filter

Effects

Strobe/Timing

Preset X(0 thru 31)

Color Filter (0 thru 43)

Master Intensity 0-100%

Zoom 0-255

Chase

Master Intensity 0-100%

Speed 0.2 S-30 Min

Fade 0-100%

Zoom 0-255

Master Intensity 0-100%

Strobe xxxx

Duration

Intensity Timing 0.2 S-60 Min

Color Timing

Zoom Timing 0.2 S-60 Min

RGB Mode

HSIC Mode Master Intensity 0-100%

Built-in Chase

0.2 S-60 Min

0-100%Master Intensity

0-100%Pixel 1-3_Red

0-100%Pixel 1-3_Green

Pixel 1-3_Blue

Pixel 1-3_White 0-100%

Zoom 0-255

DMX Through

Capture DMX

Pixel 1-3_Hue 0-359 degree

Pixel 1-3_Saturation 0-100%

Pixel 1-3_Intensity

Pixel 1-3_CCT

Zoom 0-255

DMX Through

Capture DMX

1 thru 10

Select Chase x(1 thru 8)User Chase

Edit Chase x(1 thru 8)

0--85

0-100%

On/Off

Capture DMX

0-100%

2700K-6500K

On/Off

Capture DMX

Edit Step x (1 thru 100)

New Step

Delete Step

Preset X/Color Filter X RGB Mode

HSIC Mode

Master Intensity

Pixel 1-3_Red

Pixel 1-3_Green

Pixel 1-3_Blue 0-100%

Pixel 1-3_White

Zoom

DMX Through

Capture DMX

Master Intensity

Pixel 1-3_Hue 0-359 degree

Pixel 1-3_Saturation 0-100%

Pixel 1-3_Intensity 0-100%

Pixel 1-3_CCT 2700K-6500K

Zoom 0-255

DMX Through On/Off

Capture DMX Capture DMX

0-100%

0-100%

0-100%

0-100%

0-255

On/Off

Capture DMX

0-100%

Continue on next page

Figure 9: SL PUNCHLIT E 220 Menu Tree (Part 1)

SL PUNC HLITE 2 20 Menu T ree

11

Installat ion & User’s Manu al

Contin ued f rom
previo us pa ge

SL PUNCHLIT E 220

Settings

Lock Fixture

Password

Status

Security

DMX

Enter Pass PIN Level 1-3

Pixel 1-3 LED

Current Level

Movement Zoom 0-255

Temperature

Other Information RDM UID 0X000000000000

Enter PassPIN

Level 1 PIN

Level 2 PIN

Level 3 PIN

Power-up Level

Power-upGeneral

Mode

DIM Response

Dimming Curve

(DMX 8Bit)

Fan Control

Protected NoFactory Default

DMX Enable

Address

Map

When no DMX

LED Group

Flip DisplayDisplay

Off Time

Language Select

Yes(to lock Fixture)LOCK Are you sure?

No

Master Intensity

Red

Green

Blue

White

Temperature

Warning Low

Warning High

Min_Value

Max_Value

Max Intensity 0-100%

Firmware Version Rev 0.0

****

1111

2222

3333

Locked/Level 1-3 /disable

Password

Preset X(1 thru 32)

Color Filter (1 thru 43)

Chase(1 thru 18)

Last Set

Master

Slave

Normal

Incandescent

linear

Square

S-Curve

PL-Curve

OFFCalibration

ON

Auto

OFF

Preset & Chase

NoLoad Factory

Yes

Enable

Disable

1 to 512

RGBW 16-bit Mode

RGBW 8-bit Mode

HSIC Mode

Simple 8-bit Mode

Off

Hold

Power Up

Last Action

1 or 3

No

Yes

Auto

On/30S/1Min/ 5Min/10Min

English

0-100%

0-100%

0-100%

0-100%

0-100%

xx Celsius degree

83 Celsius degree

86 Celsius degree

xx Celsius degree

xx Celsius degree

12

Figure 10: SL PUNCHLI TE 220 Menu Tree(Part 2)

SL PUNC HLITE 2 20 Menu T ree