Show Atelier DIAPro ColorBeam 5R User Manual

DIAPro ColorBeam 5R

User Guide

Please read these instructions carefully before use

TABLE OF CONTENTS

1. Safety Instruction .................................................................................... 2

2. Installation ................................................................................................ 3

3. Technical Specification ........................................................................... 5

4. Description ............................................................................................... 8

4.1 Description of the fixture ..................................................................................... 8

4.2 Control Panel ........................................................................................................ 8

5. Gobo-wheel and Lamp .......................................................................... 10

5.1 Gobos-wheel ....................................................................................................... 10

5.2 Lamp .................................................................................................................... 10

5.3 Change the Lamp ................................................................................................ 11

6. How To Set The Unit .............................................................................. 12

6.1 Power On Display ............................................................................................... 12

6.2 Main Function ..................................................................................................... 12

6.3. Home Position Adjustment ............................................................................... 24

6.4. Error Information ............................................................................................... 26

7. Control By Universal DMX Controller ................................................... 27

7.1 Connection .......................................................................................................... 27

7.2 Channel Mode Setting ........................................................................................ 28

7.3 Address Setting .................................................................................................. 29

7.4 DMX 512 Configuration ...................................................................................... 29

7.5 Lighting Library Download ................................................................................ 37

8. Update Software ..................................................................................... 37

9. Troubleshooting ..................................................................................... 37

10. Maintenance and Cleaning .................................................................. 39

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual.

Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

 Unpack and check carefully that there is no transportation damage before using the

unit.

 The unit is for indoor use only. Use only in a dry location.  Do install and operate by qualified operator.  DO NOT allow children to operate the fixture.  Use safety chain when fixing the unit. Handle the unit by carrying its base instead of

head only.

 The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces.

 Be sure that no ventilation slots are blocked; otherwise the unit will be overheated.  Before operating, ensure that the voltage and frequency of power supply matches the

power requirements of the unit.

 It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

 Maximum ambient temperature TA: 40℃. DO NOT operate it when the temperature is

higher.

 DO NOT connect the device to any dimmer pack.  During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

 Make sure there are no flammable materials close to the unit while operating to avoid

fire hazard.

 Examine the power wires carefully; replace them immediately if there is any damage.  Unit’s surface temperature may reach up to 85℃. DO NOT touch the housing

Please read carefully the instruction manual, which includes important

information about the installation, usage and maintenance.

bare-handed during its operation, and allow about 15 minutes for cooling the unit down before replacing bulb or maintenance as it could be very hot.

 Avoid any inflammable liquids, water or metal objects entering the unit. Once it

happens, cut off the mains power immediately.

 DO NOT operate in dirty or dusty environment; do clean the fixture regularly.  DO NOT touch any wire during operation as there might be a hazard of electric shock.  Avoid power wires twist other cables.  The minimum distance between light output and the illuminated surface must be more

than 12 meters.

 Disconnect mains power before fuse/lamp replacement or servicing.  Replace fuse/lamp only with the same type.  In the event of serious operating problem, stop using the unit immediately.  Never turn on and off the unit time after time.  The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

 DO NOT open the unit as there are no user serviceable parts inside.  Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead

to damage or malfunction. Please contact the nearest authorized technical assistance center if needed.

 Disconnect the mains power if the fixture is has not been used for a long time.  Do use the original packing materials before transporting it once again.  To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

 Hot lamp explosion hazard. Do not open the unit within 15 minutes after switching off.  Do replace the bulb once it is damaged, deformed or life-expired.  DO NOT look directly at the light while the bulb is on.  Never touch bulb with bare fingers, as it is very hot after using.  DO NOT start on the unit without bulb enclosure or when housing is damaged.

2. Installation

Unpacking the fixture (for flight case pack only)

1. Stop the flight case via the brake sheet above the wheels.

2. Unlock the lock modules (1) and open the cover board.

3. Prop the cover board with lid bracket.

4. Take out the fixture.

5. Unlock the lock module (2) take out omega clamps.

Installation:

1. Bolt each clamp (1) to the Omega holder with screw and lock nut through the hole in the holder.

2. Fasten the omega holders (2) on the bottom of the base by inserting quick-lock fasteners (3) into the holes of the base and tighten fully clockwise.

3. Hang the fixture to the support (4) through clamp and fasten the screws (5). Fasten the safety cable (6) through the bottom of the base and over the support.

Fig.1 Fig.2

Attention:

 Always ensure that the structure to which you are attaching the unit is secure and is

able to support a weight of 10 times of the unit’s weight without any harming deformation.

 Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

 Make absolute sure that the unit is firmly fixed in way that no vibrating or slipping would

occur during operation.

 The equipment must be installed beyond the areas where persons may walk by or be

seated.

 The rigging has to be operated by or under the guide of a skilled person.

3. Technical Specification

Power supply

- 100~240V, 50/60Hz

Power Consumption

- 330W

Lamp

- Philips MSD Platinum 5R (8000K)

Battery backup display

- Setting DMX address or other functions without connecting to mains power.

- Battery for LCD display charges automatically when the fixtures connects to the mains power.

- No need to change battery.

Wireless control (for the unit with wireless receiver built-in only)

- Wirelessly controlled by W-DMX (option).

- Each W-DMX is sending out 512 channels of DMX.

- License free band of 2.45 GHz

Optical system

- High efficient Optical system.

- Delivering extremely powerful output.

- High quality lens.

Movement

- Pan: 540°

- Tilt: 270°

- Pan/Tilt moving speed adjustable.

- Automatic Pan/Tilt correction.

- Easy calibration and maintenance by magnetic home positioning.

- Pan/Tilt position lock for transporting protection.

Dimmer/Shutter

- Mechanical dimmer

- Mechanical shutter and adjustable speed strobe effect

Color wheel

- Color wheel: 14 fixed colors

- Rainbow effect in both directions.

- Easy calibration and maintenance by magnetic home positioning.

Gobo wheel

- Gobo Wheel: 17 fixed gobos, index able,

- Easy calibration and maintenance by magnetic home positioning.

Prism

-8-facet rotating prism Frost

Zoom: From 1°~ 3.8° Focus: Electronic

Cooling:

- Fan cooling

Protocols

- DMX 512

- Data input/output: 3/5 Pin XLR socket

Dimension

- 415×344×538.5mm

Weight

- 19kg

Photometric diagram

DMX Channels:

Mode

Mode 1

19-CH

Mode 2

16-CH

Mode 3

20-CH

PAN

COLOUR WHEE

COLOUR WHEEL

PAN FINE

STOP / STROBE

TILT

DIMMER

TILT FINE

STATIC GOBO

CHANGE

STATIC GOBO

CHANGE

PAN /TILT SPEED

PRISM INSERTION

FUNCTION

PRISM ROTATION

P/T MACRO

EFFECTS

MOVEMENT

EFFECTS

MOVEMENT

P/T MACRO SPEED

FROST

COLOR

FOCUS

GOBO

PAN

PRISM

PAN FINE

R-PRISM

TILT

R-PRISM FINE

TILT FINE

EFFECTS

MOVEMENT

FUNCTION

FOCUS

RESET

FROST

LAMP CONTROL

(WITH OPTION

"LAMP DMX" ON)

LAMP CONTROL

(WITH OPTION

"LAMP DMX" ON)

SHUTTER

PAN - TILT SPEED

DIMMER

COLOUR SPEED

DIMMER FINE

BEAM SPEED

GOBO SPEED

4. Description

4.1 Description of the fixture

a. Tilt mechanism lock and release（every 45°）

b. pan mechanism lock and release（every 90°）

Caution: The head and arm must be unlocked before operation!

4.2 Control Panel

Front view Rear view

○

,1 Monitor (Batter Back-up display):

○

,2 LED:

POWER

Power On

BATTERY

Battery Status

1. Antenna (for XP-5R BEAM-WT only)

2. Front panel

3. Head

4. Arm

5. Tilt arm self-locking handle

6. pan self-locking handle

7. Handle

8. Base

WIRELESS

Receive the wireless signal

DMX

DMX input present

○

,3 Button:

To enter into, move backward or leave the menu

Move up in the menu

DOWN

Move down in the menu

ENTER

Enter the desired functions

○

,4 Antenna (for XP-5R BEAM-WT only):

Receive wireless signal from a wide range

○

,5 DMX input/output:

For DMX 512 operation, use 3/5-pin XLR plug cable to link the units together

○

,6 Fuse (T 5 A):

Protect the unit from damage of overcurrent.

○

,7 Power Cable:

To connect to the mains supply

○

,8 Power Switch:

Turns On/Off the power

10B

5. Gobo-wheel and Lamp

5.1 Gobo-wheel

DANGER!

Install/change the gobo-wheel with the device switched off only.

5.2 Lamp

Philips MSD Platinum 5R (8000K)

 Because of its high internal pressure, there might be a risk that the Discharge

lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if you take a close look at the lamp.

 To protect the lamp, always turn off the lamp first (via control panel or DMX

controller) and let the unit run at least five minutes to cool down before switching off the mains supply. Never handle the lamp or luminary when it is hot.

 Do not touch the bulb with bare hands. If this happens, clean the lamp with

denatured alcohol and wipe it with a lint free cloth before installation.

 The lamp generates UV radiation. Never operate the lamp without appropriate

shielding.

 When lighting up, the lamp operates at high pressure and there is a slight risk of arc

tube rupture. The risk increases with age, temperature and improper handling of the lamp. Do not use the lamp longer than its lifespan.

 Make sure the lamp is located in the center of the reflector for the best projection.

11B

5.3 Change the Lamp

1. Follow the Fig.1 and Fig.2: Loosen the four screws and open the cover

2. Follow the Fig.3 and Fig.4: Loosen the two screws and apart the entire assembly

3. Follow the Fig.5 and Fig.6: Unplug all the connect wires over the lamp and wear

Anti-static gloves to take on the lamp

Fig1

Fig2

Fig3

Fig4

Fig5

Fig6

12B

4. Change a new lamp

6. How To Set The Unit

6.1 Power On Display

Every time you turn on the unit, it will run built-in program to reset all motors to their home position, the display will show as fig.4, you may hear some noises for about 20 seconds. It will show warning sign if it goes wrong during resetting and you can press the MENU button to view the error information. After that the unit will be ready to receive DMX signal and the display will show as fig.5.

Fig.4 Fig.5

Explanation of fig.5:

Base 40°C

Show temperature of base CPU is 40°C

001

Show start address

Md.1 19Ch.

Show channel mode is mode 1 (19 channels mode)

6.2 Main Function

Turn on the unit, press MENU button into menu mode, press UP and DOWN button until the required function is shown on the monitor. Select the function by ENTER button. Use UP and DOWN button to choose the submenu, press the ENTER button to store and automatically return to the last menu. Press MENU button or let the unit idle one minute to exit menu mode.

+ 28 hidden pages

Show Atelier DIAPro ColorBeam 5R User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual