ShoreLand'r SLRB40TCBXLW User Manual
SLRB40TCBXLW-__ & SLRB40TCBBXLW-__
SLRB40TCBXLW-__ Shown
SLRB40TCBXLW Bundles Required:
62168 Bunk Assy Rear Bunk Kit R/B……………..2
66520 Bag with Chains, No Coupler.....................1
69082 Lit Packet Brake Trailers............................1
80784-- Frame Bundle - 2X4W 40TCBLW..............1
66996-- Tongue Assembly 55”, W/UFP Actuator....1
TA0991-__ Winch Stand Kit 9” w/Mtg HDWE………....1
(or)
TA0992-__ Winch Stand Kit 14” w/Mtg HDWE……..…1
(or)
-
ST215/75R14C Tire/TS Dir Rim................4
(or)
ST215/75R14C Tire/Galv Dir Rim..............4
”
SLRB40TCBBXLW Bundles Required:
ST215/75R14C Tire/TS Dir Rim............4
(or)
ST215/75R14C Tire/Galv Dir Rim..........4
62168 Bunk Assy Rear Bunk Kit R/B…………..2
66520 Bag with Chains, No Coupler..................1
69082 Lit Packet Brake Trailers.........................1
80785-- Frame Bundle - 2X4W 40TCBBXLW.......1
66996-- Tongue Assembly 55”, W/UFP Actuator..1
69352 Brake Kit – Tandem Axle Connection…..1
TA0991-__ Winch Stand Kit 9” w/Mtg HDWE………..1
(or)
TA0992-__ Winch Stand Kit 14” w/Mtg HDWE………1
(or)
TA0993-__ Winch Stand Kit 7” w/Mtg HDWE………..1
ShoreLand’r offers their product line in either galvanized or painted finish. When or dering parts it is important that you specify
the finish or color you have on your product. T he five (5) di git number a long with a two (2) digit spac e _ _, note the p arts which
can be purchased with various finishes. When ordering these items use the five (5) digit number along with a t wo (2) digit suffix
for the proper finish.
00..........Galvanized
01..........Arctic White
03..........Black
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004276
Page 1 of 15 10/25/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004276
Page 2 of 15 10/25/2010
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the
front cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the
tongue. Place the wire harness and the brake line
through the hole provided in the tongue cover plate.
See Detail A in Diagram A.
Secure the tongue cover plate in position with the
same 1/2” x 1-1/2” hex bolt that secur es the back on
the tongue to the tongue channel of the frame.
Secure with 1/2” lock nut. Tighten both bolts just
installed.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004276
Page 3 of 15 10/25/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004276
Page 4 of 15 10/25/2010
WINCH POST ASSEMBLY
The height that the bow eye is placed in your boat will
determine the length winch post required. Once this is
determined, attach the winch base to the tongue with
three 1/2” x 4-1/2” carriage bolts and lock nuts.
Align the holes in the Profile 2000 mounting channel
with the holes in the top of the winch base. Attach the
front of the winch head mounting channel to the base
by placing a 1/2” x 4-1/2” hex bolt through the hole
closest to the front of the winch base. Secure with a
lock nut. Do not tighten.
Note that the winch head can now be rotated either up
or down. Identify the correct hole combination to use to
position the bow eye roller just above the bow eye of
your boat. When determined, secure in this position by
placing the bushing as shown in Diagram C inside the
winch base so it aligns with the hole just identified for
the proper adjustment. Insert another 1/2” x 4-1/2” hex
bolt through the determined mounting hole in the
mounting channel and winch base making sure the bolt
passes through the bushing as well. Secure with a 1/2”
lock nut. Tighten all bolts.
Plug the tongue wire harness ends into the frame harnesses by matching colors and ends. Pushes the
extra wire provided into the rear of the tongue or
remove the grommet in the side frame and place the
extra wire in the side frame. Replace grommet just removed.
SAFETY CHAINS
Locate the 1/2” x 1-1/4” hex bolt. Slip the bolt through
a 1/2” at washer, then place through the last link of
one of the safety chains. Place a second flat washer
on the bolt and insert through the hole as shown in
Diagram B. Secure with a 1/2” .flange lock nut.
Tighten. Repeat this process on the second safety
chain on the opposite side of the tongue.
Assembly is complete.
BRAKE LINE
Locate the brass brake line coupling. Remove the
plastic cap and thread the brake line hose coming out
the rear of the tongue into one end of the coupling.
Bend the line in a smooth gradual radius being careful
not to kink the line. Bend so it can be mated to the
brake line hose from the side frame. Once aligned,
thread the side frame brake line hose into the other
end of the coupling. Tighten both lines into the
coupling.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004276
Page 5 of 15 10/25/2010
Loading...