ShoreLand'r SLR55TCBBS User Manual
SLR55TCBBS-__
SLR55TCBBS Bundles Required:
ST215/75R14C Tire/TS Dir Rim................4
66520 Bag with Chains, No Coupler.....................1
69082 Lit Packet Brake Trailers............................1
80800-- Frame Bundle – SLR55TCBBS……..........1
66996-- Tongue Assembly 55”, W/UFP Actuator....1
69352 Brake Kit Tandem Axle Connect………….1
(or)
ST215/75R14C Tire/Galv Dir Rim..............4
Tire Size and Carrying Capacity Chart
Tire Size........................ST215/75R 14-C
GVWR...........................7040 lb.
Carrying Capacity........5500 lb.
Axle...............................Disc Brakes
Refer to the tire side wall for correct tire
pressure.
ShoreLand’r offers their product line in either galvanized or painted finis h. When ordering parts it is important that you
specify the finish or color you have on your prod uct. The five (5) digit number along with a two (2) digit space _ _, no te
the parts which can be purchased with various finishes. When ordering these items use the five (5) digit number along
with a two (2) digit suffix for the proper finish.
00..........Galvanized
01..........Arctic White
03..........Black
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004292
Page 1 of 14 11/04/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004292
Page 2 of 14 11/04/2010
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the
front cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue.
Place the wire harness and the brake line through the
hole provided in the tongue cover plate.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004292
Page 3 of 14 11/04/2010
A
See Detail A in Diagram A. Secure the tongue cover plate in
position with the same 1/2” x 1-1/2” hex bolt that secures the
back on the tongue to the tongue channel of the frame. Secure
with 1/2” lock nut. Tighten both bolts just installed.
Plug the tongue wire harness ends into the frame
harnesses by matching colors and ends. Push the
extra wire provided into the rear of the tongue or remove the grommet in the side frame and place the
extra wire in the side frame. Replace grommet just
removed.
SAFETY CHAINS
Locate the 1/2” x 5” hex bolt. Slip the bolt through a 1/2” flat washer,
then place through the last link of one of the safety chain. Insert
through the hole in the actuator housing and out the other side. Slide
the last link of the other chain over the bolt and slide on a flat washer.
Secure with a 1/2” .flange lock nut. Tighten.
ssembly is complete.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004292
Page 4 of 14 11/04/2010
WINCH POST ASSEMBLY
Locate the winch post and position it on the tongue. Place the
1/2” x 3 9/16” x 6” U-bolts up around the tongue, align the legs
of the U-bolts with the holes in the winch post base and insert.
Secure the U-bolts in place using ½” flange lock nuts. Tighten
only enough to secure in place because the y will have to be
moved again for final adjustment when the boat is placed on
the trailer.
Locate the winch handle. Press the retainer clip on the end of
the winch handle so it can be slipped onto the drive shaft.
Release clip once the handle is fully on the drive shaft. Note
that the winch handle should be removed during transport to
eliminate the possibility of loosing it.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004292
Page 5 of 14 11/04/2010
Loading...