ShoreLand'r SLR55TBBL User Manual V.2
®
SLR55TBBL
Bundles Required for SLR55TBBL
69082 Literature Bag - Trailers - Brakes 1
80506-- Frame Bundle - 2X5 - R55TBBL 1
ST215/75R 14C Tire / TS Dir Rim 4
67178-- Tongue Assembly w/UFP - Disc 1
6238600 Rocker Bag - Tandem 1
69352 Brake Kit Tandem Axle Connection Hose 1
66520 Bag w/Chains - No Coupler 1
Table of Contents: Page
Frame Drawing & Bill of Materials ................................2-3
Safety Instructions ........................................................3
Tongue & Safety Chain Dwg/BOM/Assy Instr. ..............4
White Ground Wire Installation .....................................4
SP Winch Dwg/BOM/Assy Instr. ...................................5
Chassis Drawing & Bill of Materials ..............................6-7
Tire Size & Carrying Capacity Chart .............................8
Rocker Arm Instructions ............................................... 8
ShoreLand’r offers their product line in either galvanized or painted
nish. When ordering parts it is important that you specify the nish
or color you have on your product. The ve (5) digit number along
with a two (2) digit space _ _, note the parts which can be purchased
with various nishes. When ordering these items use the ve (5) digit
number along with a two (2) digit sufx for the proper nish.
00..........Galvanized
01..........Arctic White
03..........Black
33..........Galvanized w/Black Plastic Parts
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003476
Page 1 REV B 10/27/06
Spring Assembly Instructions ....................................... 8
Axle Assembly Instructions ...........................................8
Tire & Wheel Assembly ................................................8
Roller Dwg/BOM / Assembly Instructions ..................... 9-10
Trailer Adjustments .......................................................11
Axle Adjustments .......................................................11
Rear Support System Adjustment .............................11
Roller Adjustment ......................................................11
Rear Roller System Support Adjustment ...................11
Winch Post Adjustments ...........................................11
Diagram A
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003476
Page 2 REV B 10/27/06
Refer to your ShoreLand’r Owner’s
Guide and other decals on trailer for
additional information.
SAFETY INSTRUCTIONS
4810709
Proper tongue weight must be maintained.
Rev C 8/28/06
Before towing, check the following to ensure
that:
1. All parts, bolts, nuts and wheel lug
nuts are tight.
2. All wheel lug nuts must be tightened
to a minimum torque rating of 85 ft/lb.
3. Lug nuts must be re-torqued after the
first 50 miles, then periodically there
after.
4. Tires are inflated to manufacturer’s
standards. (See tire sidewall)
5. Wheel bearings have adequate
grease.
6. Hitch ball is the proper diameter and
has a rating equal to or greater than
the GVWR of the trailer.
7. Coupler is properly attached and
secured to coupler ball.
8. Trailer safety chains are crossed
under the tongue and attached to
towing vehicle.
9. All lights are operational. Note: It is
recommended that the trailer lights
be disconnected before backing into
the water.
10. Tie downs, winch strap and bow eye safety chain are secure.
11. Trailer tongue jack is in up or travel
position.
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove parts
and sort by size.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003476
Page 3 REV B 10/27/06
Diagram B
TONGUE
The tongue is shipped separate of the frame. Locate the appropriate tongue and install by sliding it in the front of the tongue channel.
Align the holes in the tongue with the holes in the tongue channel.
Install the ½” x 4” hex bolt in the front cross hole and secure with a
½” ange lock nut.
Place the wire harness and the brake line through the hole provided in the tongue cover plate. See Detail A in Diagram A. Secure
the tongue cover plate in position with the same ½” x 1 ½” hex bolt
that secures the back of the tongue to the tongue channel of the
frame. Secure with ½” ange lock nut.
Plug the tongue wire harness ends into the frame harnesses by
matching colors and ends. Push the excess wire provided back into
the rear of the tongue.
WHITE GROUND WIRE INSTALLATION
Place the self-tapping screw provided through the round metal ring
on the white ground wire of the tongue harness located at the rear
of the tongue. Attach the ground wire to the main frame by driving
the screw in the hole provided next to the tongue channel of the
frame. This will assure a positive ground for the lighting.
SAFETY CHAINS
Locate the 1/2”x 5” hex bolt. Slip the bolt through a ½” at washer,
then place through the last link of one of the safety chains. Insert
the bolt into the hole provided in the drop portion of the tongue until
it comes out the hole on the other side of the drop tongue. Place
on a second safety chain, a ½” at washer, and secure with a ½”
ange lock nut. Tighten.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003476
Page 4 REV B 10/27/06
Loading...