ShoreLand'r SLR50TCBL User Manual
SLR50TCBL-__
SLR50TCBL Bundles Required:
66520 Bag with Chains, No Coupler.....................1
69082 Lit Packet Brake Trailers............................1
80768-- Frame Bundle – SLR50TCBL…….............1
67178-- Tongue Assy W/UFP Disc 5X3X65….......1
ST215/75R14C Tire/TS Dir Rim................4
(or)
ST215/75R14C Tire/Galv Dir Rim..............4
ShoreLand’r offers their product line in either galvanized or painted finis h. When ordering parts it is important that you
specify the finish or color you have on your prod uct. The five (5) digit number along with a two (2) digit space _ _, no te
the parts which can be purchased with various finishes. When ordering these items use the five (5) digit number along
with a two (2) digit suffix for the proper finish.
00..........Galvanized
01..........Arctic White
03..........Black
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004287
Page 1 of 14 11/01/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004287
Page 2 of 14 11/01/2010
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the
front cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue.
Place the wire harness and the brake line through the
hole provided in the tongue cover plate.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004287
Page 3 of 14 11/01/2010
See Detail A in Diagram A. Secure the tongue cover
plate in position with the same 1/2” x 1-1/2” hex bolt
that secures the back on the tongue to the tongue
channel of the frame. Secure with 1/2” lock nut.
Tighten both bolts just installed.
Plug the tongue wire harness ends into the frame harnesses by matching colors and ends. Push the extra
wire provided into the rear of the tongue or remove the
grommet in the side frame and place the extra wire in
the side frame. Replace grommet just removed.
BRAKE LINE
Locate the brass brake line coupling. Remove the
plastic cap and thread the brake hose coming out the
rear of the tongue into one end of the coupling. Once
aligned, thread the side frame brake hose into the
other end of the coupling. Tighten both lines into the
coupling.
SAFETY CHAINS
Locate the 1/2” x 5” hex bolt. Slip the bolt through a 1/2” flat washer,
then place through the last link of one of the safety chain. Insert
through the hole in the actuator housing and out the other side. Slide
the last link of the other chain over the bolt and slide on a flat washer.
Secure with a 1/2” .flange lock nut. Tighten.
Assembly is complete.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004287
Page 4 of 14 11/01/2010
WINCH POST ASSEMBLY
Locate the winch post and position it on the tongue. Place the ½” x 3 9/16” x 6” U-bolts up
around the tongue, align the legs of the U-bolts with the holes in the winch post base and
insert. Secure the U-bolts in place using ½” flange lock nuts. Tighten onl y enough to secure in
place because they will have to be moved again for fi nal ad justment when the boat is placed on
the trailer.
Locate the winch handle. Press the retainer clip on the en d of the winch handle so it can be
slipped onto the drive shaft. Release clip once the handle is fully on the drive shaft. Note that
the winch handle should be removed during transport to eliminate the possibil ity of loosing it.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004287
Page 5 of 14 11/01/2010
Loading...