ShoreLand'r SLR40TCBXLW User Manual
SLR40TCBXLW-__ & SLR40TCBBXLW-__
SLR40TCBXLW-__ Shown
SLR40TCBXLW Bundles Required:
66520 Bag with Chains, No Coupler...................1
69082 Lit Packet Brake Trailers..........................1
80776-- Frame Bundle - 2X4W R40TCBXLW.......1
66996-- Tongue Assembly 55”, W/UFP Actuator..1
TA0991-__ Winch Stand Kit 9” w/Mtg Hdwe……..…..1
TA0992-__ Winch Stand Kit 14” w/Mtg Hdwe………..1
TA0993-__ Winch Stand Kit 7” w/Mtg Hdwe……..…..1
ST215/75R14C Tire/TS Dir Rim...............4
(or)
ST215/75R14C Tire/Galv Dir Rim............4
(or)
(or)
SLR40TCBBXLW Bundles Required:
ST215/75R14C Tire/TS Dir Rim...............4
(or)
ST215/75R14C Tire/Galv Dir Rim............4
66520 Bag with Chains, No Coupler...................1
69082 Lit Packet Brake Trailers..........................1
80777-- Frame Bundle - 2X4W R40TCBBXLW.....1
66996-- Tongue Assembly 55”, W/UFP Actuator..1
69352 Brake Kit - Tandem Axle Connection.......1
TA0991-__ Winch Stand Kit 9” w/Mtg Hdwe………....1
(or)
TA0992-__ Winch Stand Kit 14” w/Mtg Hdwe………..1
(or)
TA0993-__ Winch Stand Kit 7” w/Mtg Hdwe……..…..1
ShoreLand’r offers their product line in either galvanized or painted finish. When ordering parts it is important
that you specify the finish or color you have on your product. The five (5) digit number along with a two (2) digit
space _ _, note the parts which can be purchased with various finishes. When ordering these items use the
five (5) digit number along with a two (2) digit suffix for the proper finish.
00........Galvanized
01........Arctic White
03........Black
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 1 of 17 9/28/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 2 of 17 9/28/2010
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 3 of 17 9/28/2010
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 4 of 17 9/28/2010
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the
front cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the
tongue. Place the wire harness and the brake line
through the hole provided in the tongue cover plate.
See Detail A in Diagram A.
Secure the tongue cover plate in position with the
same 1/2” x 1-1/2” hex bolt that secur es the back on
the tongue to the tongue channel of the frame.
Secure with 1/2” lock nut. Tighten both bolts just
installed.
Plug the tongue wire harness ends into the frame
harnesses by matching colors and ends. Push the
extra wire provided into the rear of the tongue, or remove the grommet in the side frame and place the
extra wire in the side frame. Replace grommet just
removed.
WHITE GROUND WIRE INSTALLATION
Place the self-tapping screw provided through the
round metal ring on the white ground wire of the
tongue harness located at the rear of the tongue.
Attach the ground wire to the main frame by driving
the screw in the hole provided next to the tongue
channel of the frame. This will assure a positive
ground for the lighting.
SAFETY CHAINS
Locate the 1/2” x 1-1/4” hex bolt. Slip the bolt
through a 1/2” at washer, then place through the last
link of one of the safety chains. Place a second flat
washer on the bolt and insert through the hole as
shown in Diagram B. Secure with a 1/2” flange lock
nut. Tighten. Repeat this process on the second
safety chain on the opposite side of the tongue.
Assembly is complete.
BRAKE LINE
Locate the brass brake line coupling. Remove the
plastic cap and thread the brake line coming out the
rear of the tongue into one end of the coupling. Bend
the line in a smooth gradual radius being careful not
to kink the line. Bend so it can be mated to the brake
line from the side frame. Once aligned, thread the
side frame brake line into the other end of the
coupling. Tighten both lines into the coupling.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 5 of 17 9/28/2010
WINCH POST ASSEMBLY
The height that the bow eye is placed in your boat will
determine the length winch post required. Once this is
determined, attach the winch base to the tongue with
three 1/2” x 4-1/2” carriage bolts and lock nuts.
Align the holes in the Profile 2000 mounting channel
with the holes in the top of the winch base. Attach the
front of the winch head mounting channel to the base by
placing a 1/2” x 4-1/2” hex bolt through the hole closest
to the front of the winch base. Secure with a lock nut. Do
not tighten.
Note that the winch head can now be rotated either up
or down. Identify the correct hole combination to use
to position the bow eye roller just above the bow eye
of your boat. When determined, secure in this position
by placing the bushing as shown in Diagram C inside
the winch base so it aligns with the hole just identified
for the proper adjustment. Insert another 1/2” x 4-1/2”
hex bolt through the determined mounting hole in the
mounting channel and winch base making sure the
bolt passes through the bushing as well. Secure with
a 1/2” lock nut.
Tighten all bolts.
Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004265
Page 6 of 17 9/28/2010
Loading...