ShoreLand'r SLR22S User Manual V.1
®
SLR22S
SLR22S Bundles Required
62340 Literature Packet - Trailers
61395 Coupler Bag w/Chains
80421-- Frame Bundle 2x3 R22S
ST185/80R13-C Dir Rim
60493-- Tongue 60” 2x3 Frame
ShoreLand’r offers their product line a painted nish. When ordering
parts it is important that you specify the nish or color you have on
your product. The ve (5) digit number along with a two (2) digit space
_ _, note the parts which can be purchased with various nishes.
When ordering these items use the ve (5) digit number along with
a two (2) digit sufx for the proper nish.
00..........Galvanized
01..........Arctic White
03..........Black
33..........Galvanized w/Black Plastic Components
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003702
Page 1 11/02/06
Table of Contents: Page
Frame Drawing & Bill of Materials ................................2-3
Safety Instructions ........................................................3
Coupler & Safety Chain Dwg/BOM...............................4
Tongue Assembly Instructions ......................................4
Wire Harness Instructions ............................................4
Safety Chain Assembly Instructions .............................4
Winch Post Assembly Instructions................................4
Winch Dwg/BOM. ......................................................... 5
Chassis Drawing & Bill of Materials ..............................6-7
Spring Assembly Instructions ....................................... 8
Axle Assembly Instructions ...........................................8
Tire/Wheel Assembly ....................................................8
Tire Size & Carrying Capacity Chart .............................8
Roller Dwg/BOM/Assembly Instructions ....................... 9-10
Trailer Adjustments .......................................................11
Axle Adjustments .......................................................11
Rear Support System - Roller ...................................11
Front Support System - Roller ................................... 11
Winch Post Adjustments............................................11
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003702
Page 2 11/02/06
Refer to your ShoreLand’r Owner’s
Guide and other decals on trailer for
additional information.
SAFETY INSTRUCTIONS
4810709
Proper tongue weight must be maintained.
Rev C 8/28/06
Before towing, check the following to ensure
that:
1. All parts, bolts, nuts and wheel lug
nuts are tight.
2. All wheel lug nuts must be tightened
to a minimum torque rating of 85 ft/lb.
3. Lug nuts must be re-torqued after the
first 50 miles, then periodically there
after.
4. Tires are inflated to manufacturer’s
standards. (See tire sidewall)
5. Wheel bearings have adequate
grease.
6. Hitch ball is the proper diameter and
has a rating equal to or greater than
the GVWR of the trailer.
7. Coupler is properly attached and
secured to coupler ball.
8. Trailer safety chains are crossed
under the tongue and attached to
towing vehicle.
9. All lights are operational. Note: It is
recommended that the trailer lights
be disconnected before backing into
the water.
10. Tie downs, winch strap and bow eye safety chain are secure.
11. Trailer tongue jack is in up or travel
position.
ASSEMBLY INSTRUCTIONS
Remove all items from the frame. Locate the hardware bag and sort
all items by size.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003702
Page 3 11/02/06
TONGUE
The tongue comes shipped separate of the frame. Locate and slide the
tongue in the front tongue channel. Line the holes in the tongue with
the holes in the tongue channel. Secure with a 1/2” X 4” hex bolt and
1/2” lock nut in the front cross hole.
Locate the coupler bag. Place the coupler on the end of the
tongue, align holes and secure with one 1/2” X 4” hex bolts and
hex ange lock nuts in the rear coupler hole. Place two 1/2” X
1” hex bolts into the front holes of the coupler and secure to the
each side of the tongue with 1/2” ange lock nuts. Tighten.
WIRE HARNESS
Locate the wire harness. Push the two triangular plugs in the hole
on the top of the tongue, then out the rear of the tongue. Place
the wire harness through the hole in the tongue cover plate.
(See Detail A) Secure the tongue cover plate in position with a 1/2”
X 1-1/2” hex bolt and 1/2” lock nut. Tighten. Plug the tongue wire
harness ends into the frame harnesses by matching colors and ends.
Push the extra wire into the rear of the tongue or remove the grommets in the side frame and place the extra wire in the side frame.
Replace grommets just removed.
SAFETY CHAINS
Mount the safety chains to the front of the tongue by placing
a 3/8” at washer onto a 3/8” X 1-1/4” hex bolt, then insert the
bolt through the last link of the safety chain. Put the bolt through
the hole on one side of the tongue as shown. Place on another
at washer and secure with a 3/8” hex ange nut. Tighten. Repeat on the other chain on the other side of the tongue.
WINCH POST
Place t he winc h pos t assembly on the tong ue and secur e
wi th three 3/8” X 4 ” hex b ol ts and hex flange l oc k nu ts.
Place the nuts on the bolts but do not tighten because they
will have to be readjusted once the boat is on the trailer.
Remove the winch handle nut from the shaft. Align the hole in the
winch handle with the at surfaces on the shaft. Slide in position and
secure with the nut just removed. Tighten.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003702
Page 4 11/02/06
Loading...