ShoreLand'r SLIB55TBBL User Manual

SLIB55TBBL-00 & SLIB55TBBL-03

INBOARD TRAILER 2 X 5 X 80 5500LBS

SLIB55TBBL-00 BUNDLES

66520 Bag with Chains No Coupler
69352 Brake Kit Tandem Axle Connect
69082 Lit Packet Brake Trailer
6931900 Tongue Assy W/UFP Disc 5X3X78
8072900 Frame Bundle Inboard 2X5 SLIB55
ST215/75R14C Tire /Galv Dir Rim
TA0181-00 Winch Stand Kit 9 1/2 Heavy Wall
OR
TA0182-00 Winch Stand Kit 13 1/2 Heavy Wall

SLIB55TBBL-03 BUNDLES

66520 Bag with Chains No Coupler
69352 Brake Kit Tandem Axle Connect
69082 Lit Packet Brake Trailer
6931903 Tongue Assy W/UFP Disc 5X3X78
8072903 Frame Bundle Inboard 2X5 SLIB55
ST215/75R14C Tire /TS Dir Rim
TA0181-03 Winch Stand Kit 9 1/2 Heavy Wall
OR
TA0182-03 Winch Stand Kit 13 1/2 Heavy Wall

ShoreLand’r offers their product with
different finishes. When ordering parts it is
important that you specify the finish or
color you have on your product. The five
(5) digit number along with a two (2) digit
suffix, note the parts which can be
purchased with various finishes.

00…….Galvanized
03…….Black

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004169
Page 1 of 14 Rev A 10/20/2010

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004169
Page 2 of 14 Rev A 10/20/2010

Final Assembly Instructions

Remove all banded items and the hardware
bag from the frame. Open the parts bag and
remove the parts and sort the hardware by
size.

Tongue

Locate the tongue/tongue assembly and
install by sliding the angle cut end into the
tongue channel.
Align the hole in the side of the tongue with
the hole in the side of the tongue channel
and insert a 1/2” X 4” hex bolt and secure
with a 1/2” flange locknut.
Remove the tongue wire harness and brake
hose from the rear of the tongue, and slide
them thru the hole in the tongue cover plate.
Secure the tongue cover plat to the rear of
the tongue and tongue channel with a 1/2” X
1 1/2” hex bolt and secure with a 1/2” flange
locknut.
Tighten both bolts installed in the tongue.
Plug the tongue harness ends into the
frame harness ends by matching colors and
ends. With both connected the extra wire
can be pushed back into the tongue leaving
only the wire covered with the wire loom
exposed.

Tongue Brake Hose Connection

Remove the plastic caps from the side
frame brake hose and the brass plug from
the tongue brake hose. Thread the side
frame hose into the tube coupling on the
tongue hose and tighten only snug enough
to not leak. Push the excess brake line hose
back into the tongue so the connection is
inside the tongue.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004169
Page 3 of 14 Rev A 10/20/2010

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004169
Page 4 of 14 Rev A 10/20/2010

Safety Chains

Locate the 1/2” X 5” hex bolt and slip on a
1/2” flat washer, next insert into the last
link on the safety chain and then thru the
hole in the actuator housing and tongue.
Slide another safety chain over the
exposed end of the bolt add another 1/2”
flat washer and secure with a 1/2” flange
locknut.

Winch Post Installation

The height of the bow eye on your boat will
determine the required length of winch post
needed. With that determined attach the
winch post base to the tongue with three
(3)1/2” X 4” carriage bolts and secure with
1/2” flange locknuts.
Align the holes in the Profile 2000 mounting
channel with the holes in the top of the
winch base. Attach the front of the winch
head mounting channel to the base by
inserting a 1/2” X 4 1/2” hex bolt through the
hole closest to the front of the winch base
and secure with a flange locknut.
Note that the winch head can now be
rotated up or down to be positioned just
above the bow eye. When determined, align
the holes in the mounting channel with
those in the base and insert a 1/2” X 4 1/2”
hex bolt making sure to align the bushing
with the bolt and holes on the inside of the
winch base. With the bolt threads exposed
on the right side of the trailer secure with a
1/2” flange locknut. Tighten all bolts.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004169
Page 5 of 14 Rev A 10/20/2010