ShoreLand'r SLB58TCBB User Manual

SLB58TCBB & SLR58TCBB

3X5 Bunk & Roller Trailers

ShoreLand’r offers their prod uct line in either

galvanized or painted finish. When ordering
parts it is important that you specify the finish
or color you have on your product. The five (5)
digit number along with a two (2) digit space _
_, note the parts which can be purchased with
various finishes. When ordering these items
use the five (5) digit number along with a two
(2) digit suffix for the proper finish.

00..........Galvanized

01..........Arctic White

03..........Black

SLB58TCBB-__ 3X5 Bunk Trailer

ST215/75R14C Tire & Rim
4510658 Actuator – 16000# UFP GDC160
61778__ Bunk Assy 36in with Brkts 3X8
62466__ Support Tube Assy for 3X5
80749__ Frame Bundle 3X5 B&R58TBB FG
70750 Brake Kit 3X5 Tandem Brake
69082 Lit Packet Brake Trailer
69976__ Tongue Wment 58/68/80 Steel

Tire Size and Carrying Capacity Chart

Tire Size........................ST215/75R14-C

GVWR...........................7480 lb.

Carrying Capacity........5800 lb.

Axle...............................Disc Brakes

Refer to the tire side wall for correct tire pressure.

SLR58TCBB-__ 3X5 Roller Trailer

ST215/75R14C Tire & Rim
4510658 Actuator–16000# UFP GDC160
60617__ Rollerarm Assy 24 ½”
62466__ Support Tube Assy for 3X5
80749__ Frame Bundle 3X5 B&R58TBB FG
70750 Brake Kit 3X5 Tandem Brake
69082 Lit Packet Brake Trailer
69976__ Tongue Wment 58/68/80 Steel

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004215
Page 1 of 13 7/23/2010

p

FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove

arts and sort by size.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004215
Page 2 of 13 7/23/2010

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004215
Page 3 of 13 7/23/2010

Tongue

The tongue comes shipped separately. Locate and install under the frames front tongue channel and in the
channel welded to the front cross member which will support the rear of the tongue.
Align the hole in the tongue with the hole in the tongue channel. Install the 1/2” x 4-1/2” carriage bolt in the
front hole and secure with a 1/2” lock nut. Secure the rear of the tongue to the frame with a 1/2” x 4” hex bolt
and lock nut. Tighten.

Tongue Wire Harness

Locate the tongue wire harness. Place the end of the wire harness with the two three wire triangular plugs into
the hole in the top of the tongue. Pull backwards through the tongue until they can be fished through the holes
in each side of the tongue. Note that the brown, white, and yellow harness must go to the left side of the trailer
and the brown, white, and green harness must go to the right side of the trailer.

Plug the tongue wire harness ends into the frame
harnesses by matching colors and ends. Push the
extra wire provided, either into the hole in the tongue
or else remove the grommet in the side frame and
place the extra wire in the side frame. Place
grommets into all the wire holes. Replace grommets
just removed from the side frames.

Safety Chains

Mount the safety chains to the front of the tongue by
placing a 1/2” flat washer onto a 1/2” x 1 1/2” hex
bolt, and then insert the bolt through the last link on
one of the safety chains provided. Insert the bolt
through the hole provided in the front of the tongue
as shown. Secure with a 1/2” hex flange lock nut.
Repeat the process on the other chain. Tighten.

Midwest Industries, Inc. Ida Grove, IA 51445 800-859-3028 www.shorelandr.com 0004215
Page 4 of 13 7/23/2010

Actuator

Locate the actuator, and position it on the front of the
tongue as shown. Look into the back end of the actuator
and locate the solenoid. Note there is a wire harness
coiled around the round solenoid. Uncoil the wire and
plug it into the bullet plug on the end of the blue wire of
the tongue harness. Remove the plastic plug from the
port in the rear of the solenoid. Thread the fitting on the
end of the tongue brake hose into the port of the
solenoid. Tighten.
Align the holes in the actuator with the holes in the
tongue. Secure the actuator to the tongue using three
(3) 1/2” x 4” hex bolts and lock nuts. Tighten.
Thread the brass coupling provided on the other end of
the brake hose just installed. Align so it can be mated to
the brake hose from the side frame. Once aligned
thread the side frame brake hose into the other end of
the coupling. Tighten both hoses into the coupling.