ShoreLand'r SLB40TBLW User Manual
®
SLB40TBLW
SLB40TBLW Bundles Required:
4300241 ST175/80R13C MR Tire/TS Dir Rim ...........2
(or)
4300240 ST175/80R13C MR Tire/Galv Dir Rim ........2
66520 Bag with Chains, No Coupler .....................1
62340 Literature Bag - Trailers .............................. 1
80256-- Frame Bundle - 2X4W B40TBLW ..............1
66996-- Tongue Assembly 55”, W/UFP Actuator ..... 1
ShoreLand’r offers their product line in either galvanized or
painted finish. When ordering parts it is important that you
specify the finish or color you have on your product. The five
(5) digit number along with a two (2) digit space _ _, note the
parts which can be purchased with various finishes. When
ordering these items use the five (5) digit number along with
a two (2) digit suffix for the proper finish.
00 .........Galvanized
01 .........Arctic White
03 .........Black
33 .........Galvanized w/Black Plastic Parts
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003449
Page 1
Table of Contents: Page
Frame Drawing & Bill of Materials ............................. 2-3
Bunk Assembly Instructions ......................................3
Tongue & Safety Chain Dwg/BOM ............................ 4-5
Safety Instructions ..................................................... 5
Tongue Assembly Instructions ................................... 5
White Ground Wire Installation Instructions ..............5
Safety Chain Assembly Instructions .......................... 5
Brake Line Instructions .............................................. 5
Profile 2000 Winch Dwg/BOM/Assy Instr. ................ 6-7
Chassis Drawing & Bill of Materials ...........................8-9
Tire Size & Carrying Capacity Chart .......................... 9
Rocker Arm Assembly Instructions ............................ 9
Spring Assembly Instructions .................................... 9-10
Axle Assembly Instructions ........................................ 10
One Axle brake Installation ........................................ 10
Tire & Wheel Assembly ............................................. 10
Trailer Adjustments .................................................... 10-11
Axle Adjustments ....................................................... 10
Rear Support System ................................................ 10-11
Bunks ........................................................................ 11
Front Bunk Support ...................................................11
Winch Post Adjustments ............................................ 11
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003449
Page 2
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
B-SERIES BUNK ASSEMBLY
Locate the two 2 x 6 bunk assemblies. Note that the
bunk mounting brackets are assembled to the bunks
at the factory. Place the end with the two brackets towards the rear of the trailer. Place the assembly on the
equiload bunk arm and secure by placing a 3/8” x 1”
hex bolt through the bracket on the bunk and the ear
on the end of the equiload arm.Secure in place using
a 3/8” lock nut. Repeat on the other end of the arm.
(See Diagram A).
Place the other end of the bunk in the bracket installed
on the front cross member. Note that this bracket is
not attached to the bunk because the trailer can be
adjusted to two different lengths.
Once the proper position for the rear cross member is
determined, the front of the bunk can now be attached
to the bracket using two- No. 10 x 1-1/4” self tapping
screws as shown in Detail B.
The 3/8” x 1” bolts attaching the bunks to the equiload
arms and front bunk bracket can be tightened but not
over tightened. The bunks must be allowed to rotate
slightly to conform to the boat bottom once the boat is
set on the trailer.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003449
Page 3
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003449
Page 4
Loading...