ShoreLand'r SLB2313BL User Manual
®
SLB2313BL
SLB2313BL Bundles Required:
4300236 ST185/80R13C MR Tire/TS Dir Rim ...........2
(or)
4300237 ST185/80R13C MR Tire/Galv Dir Rim ........2
66520 Bag with Chains, No Coupler .....................1
69082 Literature Bag - Trailers - Brakes ...............1
80227-- Frame Bundle - 2X4W B2313BL ............... 1
66996-- Tongue Assembly 55”, W/UFP Actuator ..... 1
ShoreLand’r offers their product line in either galvanized or
painted finish. When ordering parts it is important that you
specify the finish or color you have on your product. The five
(5) digit number along with a two (2) digit space _ _, note the
parts which can be purchased with various finishes. When
ordering these items use the five (5) digit number along with
a two (2) digit suffix for the proper finish.
00 .........Galvanized
01 .........Arctic White
03 .........Black
33 .........Galvanized w/Black Plastic Parts
Table of Contents: Page
Frame Drawing & Bill of Materials ................................2-3
Bunk Assembly Instructions .........................................3
Safety Instructions ........................................................3
Tongue, Actuator & Safety Chain Dwg/BOM. ............... 4
Tongue Assembly Instructions ......................................5
White Ground Wire Installation .....................................5
Safety Chains Instructions ............................................5
Brakeline Instructions ................................................... 5
Profile 2000 Winch Dwg/BOM/Assy Instr. ................... 6-7
Chassis Drawing & Bill of Materials ..............................8-9
Tire Size & Carrying Capacity Chart .............................9
Spring Assembly Instructions ....................................... 9
Axle Assembly Instructions ...........................................9
One Axle Brake Installation .......................................... 9
Tire & Wheel Assembly ................................................10
Trailer Adjustments .......................................................10
Axle Adjustments ...................................................... 10
Rear Support System ...............................................10
Bunks ........................................................................10
Front Bunk Support ................................................... 10
Winch Post Adjustments ...........................................10
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003392
Page 1
Diagram A
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003392
Page 2
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove parts
and sort by size.
B-SERIES BUNK ASSEMBLY
Locate the two 2 x 6 bunk assemblies. Note that the bunk
mounting brackets are assembled to the bunks at the factory. Place the end with the two brackets towards the rear of
the trailer. Place the assembly on the equiload bunk arm and
secure by placing a 3/8” x 1” hex bolt through the bracket on
the bunk and the ear on the end of the equiload arm. Secure
in place using a 3/8” lock nut. Repeat on the other end of the
arm. (See Diagram A).
Place the other end of the bunk in the bracket installed on the
front cross member. Note that this bracket is not attached to
the bunk because the trailer can be adjusted to two different
lengths. Once the proper position for the rear crossmember
is determined, the front of the bunk can now be attached to
the bracket using two- No. 10 x 1-1/4” self tapping screws as
shown in Detail B.
The 3/8” x 1” bolts attaching the bunks to the equiload arms
and front bunk bracket can be tightened but not over tightened.
The bunks must be allowed to rotate slightly to conform to
the boat bottom once the boat is set on the
trailer.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003392
Page 3
Loading...