®
PWC1000
This manual only applies to models after VIN number 199717.
PWC1000 Single PWC Trailer - 1200 - White
2 4300183 4.80 X 12-B Tire/MSilver Mod Rim
1 62340 Literature Bag - Trailers
1 6249201 Frame Bundle - Single PWC - Wht
PWCG1000 Single PWC Trailer - 1200 - Galv.
2 4300205 4.80 X 12-B Tire/Galv. Mod Rim
1 62340 Literature Bag - Trailers
1 6249200 Frame Bundle-Single PWC - Galv.
PWCBK1000 Single PWC Trailer - 1200 - Black
2 4300183 4.80 X 12-B Tire/MSilver Mod Rim
1 62340 Literature Bag - Trailers
1 6249203 Frame Bundle-Single PWC - Black
Final Assembly Instructions
Remove all small parts from the frame by cutting the bands.
Remove the bolt bag and sort all nuts and bolts by size.
Tongue:
Remove the tongue assembly from the frame bundle and
slide into the tongue channel. Secure with a 3/8” X 4”
carriage bolt in the front and 3/8” X 3-7/16” X 4-1/8” square
u-bolt, 1” X 4-1/2” mounting strap and 3/8” flange lock nut in
Tire Size &
Carrying Capacity Chart
Tire Load Carrying
Size Range Capacity
4.80 X 12 B 780 lbs. per/tire
Refer to tire side wall for correct tire pressure.
Tongue Weight Adjustment
Slide the water vehicle either forward or backward on the
trailer until the proper tongue weight has been achieved.
the rear of the assembly. Thread the tongue wire harness
through the tongue and connect to the frame
harness and install the grommets. NOTE: Install the tongue
in one of the two adjustment holes in the tongue channel.
Refer to the parts drawing for placement.
Safety Chain:
Insert a 3/8” X 1-1/4” hex bolt with a 3/8” flat washer and
Material List for the PWC1000
NOTE: ShoreLand’r offers their product line in either galvanized or painted finish. When ordering parts it is important that you specify the
finish or color you have on your product. The five digit number along with a two digit space _ _, notes the parts which can be purchased
with various finishes. When ordering these items use the five digit prefix and include the following two digit suffix for proper finish.
Suffix Finish / Color
00 or G Galvanized
01 Arctic White
03 or BK Black
ASSEMBLIES:
3110253 LATCH KIT
62488-- WINCH ASSEMBLY
67381P 6’ BUNK ASSEMBLY
62491 HARDWARE BAG
62490-- AXLE ASSEMBLY
SS818 1-1/16” - 1-1/16” HUB & BEARING KIT
BK-6 1-1/16” - 1-1/16” BEARING KIT
DECALS:
4810709 TRAILER-CAUTION/WARN DECAL ..... 1
4811410 PWC DECAL ......................................... 2
4850360 NMMA CERTIFIED TRAILER DECAL ... 1
Parts Drawing
NOTE: Optional equipment
and replacement parts must
be purchased through an
authorized ShoreLand’r dealer.
safety chain through the lower hole on the front of the tongue.
Secure with a 3/8” flat washer and 3/8” flange lock nut.
Repeat this procedure on the opposite side of the tongue.
Coupler:
Mount the coupler onto the tongue with one (1) 1/2” X 4” hex
bolt and two (2) 1/2” X 1” hex bolts. Secure with 1/2” flange
lock nuts.
Winch Post:
Attach the winch brace to the winch post assembly with a 3/
8” X 4” hex bolt in one (1) of the three (3) holes of adjustment
desired. Position the winch assembly on the tongue in the
desired position and fasten with a 3/8” X
3-7/16” X 4-1/8” square u-bolts, 1” X 4-1/2” mounting straps
and 3/8” flange lock nuts.
Axle:
Install the spring bushing in the rear spring
brackets with 1/2” X 3-1/4” hex bolts and 1/2” flange lock
nuts. Position the axle under the trailer with the spring eye to
the front. Slip the flat end of the spring in the rear spring
bracket and fasten the front spring eye to the front of the
spring bracket with 9/16” X 3-1/4” hex bolts and 9/16” hex
lock nuts.
Mount the tire and rim assemblies with 1/2” lug nuts and
tighten to 80-90 ft./lbs. of torque.
Bunk:
Slide a 3/8” X 2-7/16” X 2-3/4” square bolt over the rear cross
member with the threads facing the REAR. Place an
adjustable bunk bracket on the u-bolt legs and
secure with 3/8” flange lock nuts. Slide a 3/8” X 2-7/16” X
2-3/4” square u-bolt over the front cross member with the
threads facing the FRONT. Place a adjustable bunk bracket
on the u-bolt legs and secure with 3/8” flange lock nuts. Fasten the bunk assembly to the adjustable bunk
brackets just mounted and secure with 3/8” X 1” hex bolts
and 3/8” flange lock nuts.
CAUTION:
To prevent damage to your water vehicle hull, place the
water vehicle on the trailer, loosen bunk u-bolts so the bunks
conform to the hull. Tighten.
To prevent damage the trailer or vehicle, tighten all fasteners
before towing.
The law requires that the white wire on both the tongue and
vehicle wire harness be grounded to the trailer and towing
vehicle.
Midwest Industries, Inc. Ida Grove, IA 51445 (800)859-3028 www.shorelandr.com 0003109
Loading...