ShoreLand'r PT2347TB User Manual
®
PT2347TB
Pontoon Trailer
PT2347TB Pontoon Trailer
69890 Brake First Axle Hose Kit - 8”
69082 Lit Packet - Trailers - Brakes
80638-_ _ Frame Bundle - PT2347TB
*20.5X8X10E Tire/Rim
69677-_ _ Tongue Assy 90” - Pontoon Disc
*Check with your dealer/customer service representative for current tire/rim assembly part number.
ShoreLand’r offers its product line in painted nishes. When
ordering parts, it is important that you specify the nish or
color you have on your product. The 5-digit number along
with a 2-digit space _ _, note that the parts can be purchased
in various nishes.
00........ Galvanized
03........ Black
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003940
Page 1 05/06/2008
Tire Size and Carrying Capacity Chart
Tire Size ............................20.5X8X10E
GVWR ...............................6080 lb.
Carrying Capacity ............4700 lb.
Axle ...................................Tandem - Single Brake
Refer to the tire side wall for correct tire pressure.
NOTE: Brakes available as optional equipment.
Diagram A
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003940
Page 2 05/06/2008
Remove the small parts from the frame by cutting the banding. Remove the bolt bag and sort all the nuts and bolts by size.
SAFETY CHAINS
Insert a 3/8” x 1 ¼” hex bolt through a 3/8” at washer and then into
the end link of one safety chain. Insert the bolt into the front bottom
hole punched in the tongue. Place another 3/8” at washer on the
bolt and secure with a 3/8” ange lock nut. Tighten.
Repeat this process on the other safety chain.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003940
Page 3 05/06/2008
Diagram B
TONGUE
See Diagram B.
Locate the proper length tongue. Insert the rear of the tongue into
the frame tongue channel until the mounting holes line up. Locate
the wire harness. Unwind and insert the end with the two plugs that
mate with the frame harness into the hole and route out the rear of
the tongue. Place a rubber grommet around the wire in the hole on
top of the tongue.
If brakes are going to be installed, the line should be installed inside
the tongue at this time.
SIDE MARKER LIGHTS FOR TONGUE
Note: When installing the tongue in the trailer, the side marker
lights will have to be mounted to the tongue. They are shipped in a
bag that is attached to the tongue. Insert the wire harness from the
side marker light into the larger hole in the side of the tongue, then
route the wire harness to the rear of the tongue. Attach the bezel
with the rivets provided. Plug the side marker light into the two female ends of the wire harness just pulled through on the large side
hole. Snap the light assembly into the bezel. Repeat on the other
side marker light.
Secure the tongue into the frame by placing a ½” x 4” cross bolt in
the front of the tongue channel. Locate the tongue cover plate as
shown in Diagram A, Detail A. Feed the wire harness and brake line
if applicable through the hole in the tongue cover plate. Position the
tongue cover plate so the mounting hole aligns with the hole in the
rear bottom of the tongue. Place a ½” x 1 ½” hex bolt downward
through the tongue cover plate, tongue and tongue channel. Se-
cure both mounting bolts with ½ ange lock nuts. Tighten.
Plug the tongue wire harness ends into the frame harnesses by
matching colors and ends. Push the excess wire provided either
into the rear of the tongue or else remove the grommet in the side
frame and place the excess wire in the side frame. Replace grommet just removed.
COUPLER
Locate the coupler. Drop it into position on the front of the tongue.
Secure it to the tongue using a ½” x 4” hex bolt through the rear
mounting hole of the coupler housing. Insert completely through
the tongue, then secure in place with a ½” ange lock nut.
Attach the front of the coupler to the tongue using two- ½” x 1” hex
bolts. Insert the bolt through one side of the coupler housing and
the tongue. Secure inside the tongue using a ½” ange lock nut.
Repeat this process on the other side of the tongue. Tighten all attaching bolts securely.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003940
Page 4 05/06/2008
Loading...