ShoreLand'r PT2030TB-13 User Manual

®

PT2030T-13B & PT2030T-13GB

Parts Manual

Bundles Required

PT2030T-13B Pontoon 20’ Tandem Trailer - 3000 lbs.

4 4300214 ST175/80R13C Tire/MSilver Dir Rim
1 6471503 Pontoon Axle Assy W/Brakes
1 62340 Literature Bag - Trailers
1 6607701 Frame Bundle - PT2030T-13B

PT2030T-13GB Pontoon 20’ Tandem Trailer - 3000 lbs.

4 4300213 ST175/80R13C Tire/Galv Dir Rim
1 6471500 Pontoon Axle Assy W/Brakes
1 62340 Literature Bag - Trailers
1 6607700 Frame Bundle - PT2030T-13GB

Final Assembly Instructions

Remove the small parts from the frame by cutting the
bands. Remove the bolt bag and sort all the nuts and bolts
by size.

Springs:

Mount the springs under the axle with the 1/2” X 6-1/2”
axle u-bolts from the top down. Install the spring plate
under the axle. Tighten with 1/2” flange lock nuts evenly.

Tongue Weight Adjustment

Approximate Tongue Weight for Best Towing.

Tongue weight too high, move the axle assembly forward.
Tongue weight too low, move the axle assembly backward.
Tongue weight should be 5% to 7% of the total gross
weight of the boat and trailer combined.

Tire Size & Carrying

Capacity Chart

Tire Load Carrying
Size Range Capacity

ST175/80R C 1360 lb. per/tire

Refer to tire side wall for proper tire pressure.

hex lock nut. Repeat on the other side. Position the axle
under the frame, then hook the spring loop around the
bushing just installed. Raise the axle assembly up so the
front of the springs line up with the front spring bracket
hole. Insert the other two (2) 9/16” X 3-1/4” hex bolts and
9/16” hex lock nuts. Tighten all nuts and bolts but do not
over tighten. Allow the spring room enough to move.
Mount the tire and rim assemblies using 80-90 ft. lbs. of
torque on the lug nuts using a proper tightening procedure.

Fenders:

Install the fenders and spring bracket assembly to the side
frame using 1/2” u-bolts (Ref.#108) in the area that would
best provide the proper tongue weight.

Rocker Arm:

Align center hole of 6239210, rocker arm, with the center
hole of the spring bracket. Secure with 3/4” X 4-1/2” hex
bolt from the outside-in. Tighten with a 3/4” hex lock nut.

Axle:

Make certain hook end of the springs point in the same
direction to the rear of the trailer - on both axles! Place one
of the spring bushings (Ref.#66) into the rear of the spring
bracket and secure with a 9/16” X 3-1/4” hex bolt and 9/16”

Tongue:

Install the 9’ tongue wire and grommet in the tongue.
Install the tongue into the nose cone of the trailer frame.
Secure the tongue plate cover (Ref.#4) and the rear of the
tongue with a 1/2” X 1-1/2” hex bolt, 1/2” flat washer and
1/2” hex lock nut. Secure the tongue into the side of the
frame tongue cap using a 1/2” X 4” hex bolt and 1/2” flange
lock nut. Tighten both bolts. Install the coupler on the
tongue and secure with one (1) 1/2” X 4” and two (2) 1/2” X
1” hex bolts. Tighten using 1/2” flange lock nuts. Do not

overtighten.

Actuator & Safety Chain:

Slide the actuator (Ref.#97) into the actuator housing unit
(Ref.#99) and secure with two (2) pins and snap rings
provided with the actuator. Secure the actuator - housing

Material List for the PT2030T-13B

NOTE: ShoreLand’r offers their product line in either galvanized or a painted finish. When ordering parts it is important that you specify

the finish or color you have on your product. The five digit number along with a two digit space _ _, notes the parts which can be
purchased with various finishes. When ordering these items use the five digit prefix and include the following two digit suffix for proper
finish.

Suffix Finish / Color Suffix Finish / Color

00 or G Galvanized 03 or BK Black
01 Arctic White 06 or AW Antique White

REF# PART# DESCRIPTION QTY

1 0110059 3/8” X 3-3/4” HEX BOLT ...................................... 1

2 0210058 5/16” X 1” CARRIAGE BOLT, SS ........................ 8

3 0110114 1/2” X 4” HEX BOLT ............................................ 6

4 S-3510 TONGUE PLATE COVER - WHITE ..................... 1

-- S3510G TONGUE PLATE COVER - GALV ....................... 1

5 3510538 MOLDED REAR CROSSMEMBER PAD ............ 2

6 0110170 9/16” X 3-1/4” HEX BOLT .................................... 4

7 0140040 3/8” X 1” HEX BOLT ............................................ 10

8 0110120 1/2” X 5” HEX BOLT ............................................ 1

9 64004-- PONTOON BUNK SUPPORT SADDLE .............. 8

10 3510158 PLASTIC DRIVE RIVOT ...................................... 8

11 0310170 1/2” X 2-5/16” X 6-1/2” SQUARE U-BOLT ........... 8

12 0340200 1/2” X 3-9/16” X 6” SQUARE U-BOLT ................. 2

13 0710052 1/4” X 1-1/2” HH LAG SCREW ............................ 16

14 5110113 RED SIDE MARKER LIGHT ................................ 2

15 0810925 #10 X 3/4” TEK SCREW ...................................... 6

16 1310025 5/16” S/T MED LOCK WASHER.......................... 8

17 0220110 3/8” X 1-1/2” FULL THREAD CARR BOLT .......... 2

18 1340095 3/8” FLAT WASHER ............................................ 11

19 1340206 1-1/2” OD X 13/16” ID WASHER ......................... 4

20 1410229 1/2” HEX LUG NUT.............................................. 20

21 1440101 3/8” FLANGE LOCK NUT .................................... 12

22 1310170 #10 USS FLAT WASHER .................................... 2

23 1440102 1/2” FLANGE LOCK NUT .................................... 35

24 1440259 9/16” LOCK NUT.................................................. 8

25 1440349 3/4” SLOTTED HEX NUT .................................... 4

26 1540038 1/8” X 1-1/2” COTTER KEY ................................. 4

27 S-3390 STEP PAD - LEFT ............................................... 1

-- BK-3390 STEP PAD - LEFT - BLACK ................................ 1

28 2220272 37” CHAIN ........................................................... 2

29 S-3391 STEP PAD - RIGHT ............................................. 1

-- BK-3391 STEP PAD - RIGHT - BLACK .............................. 1

30 3110241 WINCH HANDLE ................................................. 1

31 4510505 COUPLING .......................................................... 1

32 5110100 METAL FRAME CLIP .......................................... 4

33 3510030 7/8” MOLDED GROMMET .................................. 8

34 3510022 7/16” RUBBER GROMMET ................................. 9

35 1340030 3/8” S/T MED LOCK WASHER............................ 2

36 4410089 SPINDLE SLEEVE - 1-3/8” - 1-1/16”.................... 4

37 4410247 BEARING BUDDY - SS ....................................... 4

38 4410130 1-3/8” SEAL ......................................................... 4

39 4440170 1-3/8” ROLLER BEARING ................................... 4

-- 4440220 1-3/8” RACE ........................................................ 4

40 4470400 1-3/8” -1-1/16” CAST HUB ................................... 2

41 4440160 1-1/16” ROLLER BEARING ................................. 4

-- 4440210 1-1/16” RACE ...................................................... 4

42 4610072 5-LEAF SPRING .................................................. 4

43 5110045 3-LIGHT CLUSTER ............................................. 1

44 0810945 1/4” X 3/4” HWH SELF DRILL SCREW ............... 1

45 5110348 LICENSE PLATE BRACKET ............................... 1

46 5110112 AMBER SIDE MARKER LIGHT........................... 2

47 5110127 AMBER ADHESIVE REFLECTOR ...................... 2

48 5110404 FRAME HARNESS, LEFT ................................... 1

49 5110334 FRAME HARNESS - RIGHT ............................... 1

50 5110377 WATERPROOF TAILLIGHT - RIGHT.................. 1

51 5110378 WATERPROOF TAILLIGHT - LEFT .................... 1

52 5110426 TONGUE HARNESS - 9’ ..................................... 1

53 3510122 LIGHT BEZEL - WHITE ....................................... 4

-- 3510128 LIGHT BEZEL - BLACK ....................................... 4

54 5110365 2X5 TANDEM FENDER WIRE - RIGHT .............. 2

55 1410209 1/2” HEX LOCK NUT ........................................... 1

56 1410109 3/8” HEX FINISH NUT ......................................... 2

57 4410246 BEARING BUDDY BRA....................................... 4

58 64708-- FENDER WELDMENT - TANDEM PONTOON ... 2

59 0810126 1/4” X 1/2” SELF-TAPPING SCREW ................... 4

60 3110345 DL1800A WINCH W/STRAP .............................. 1

61 60876-- PONTOON AXLE ................................................ 2

62 65607-- 78” TONGUE - PONTOON .................................. 1

63 64560-- PONTOON FRAME WELDMENT ....................... 1

REF# PART# DESCRIPTION QTY

64 65014-- HAND RAIL .......................................................... 1

65 5110456 LIGHT AMBER SIDE MARKER W/36” WIRE ...... 2

66 S-3207G SPRING BRACKET BUSHING ............................ 4

67 64014 14’ PONTOON BUNK .......................................... 4

68 S-3449G SPRING PLATE ................................................... 4

69 65015-- BOTTOM WINCH POST WELDMENT ................ 1

70 4300214 ST175/80R13C TIRE/MSILVER DIR RIM ........... 4

-- 4300213 ST175/80R13C TIRE/GALV RIM ......................... 4

71 1340100 1/2” FLAT WASHER ............................................ 1

72 1410069 5/16” HEX FIN. NUT ............................................ 8

73 65016-- TOP WINCH POST WELDMENT ........................ 1

74 0110096 1/2” X 1-1/2” HEX BOLT ...................................... 1

75 0140047 3/8” X 1-3/4” HEX BOLT ...................................... 6

76 LH308 ALUMINUM CUP WASHER ................................ 2

77 60880-- 9” RF/LR PONTOON PLASTIC FENDER ........... 2

78 60887-- 9” LF/RR PONTOON PLASTIC FENDER ........... 2

79 3510104 1” ADHESIVE FLEXTRED - OCEAN GRAY........ 3 FT.

80 3610050 BRONZE ROCKER BUSHING ............................ 2

81 1440319 3/4” HEX LOCK NUT ........................................... 2

82 0110282 3/4” X 4-1/2” HEX BOLT ...................................... 2

83 0210032 1/4” X 3/4” CARRIAGE BOLT .............................. 2

84 1310004 1/4” INTERNAL TOOTH LOCK WASHER ........... 2

85 1410049 1/4” HEX FINISH NUT ......................................... 2

86 6239210 TANDEM BOGIE ................................................. 2

87 4540015 10” HUB & DRUM ................................................ 2

88 4540063 10” PREMIER FREE BACKING BRAKE - LT ...... 1

-- 4540062 -10” PREMIER FREE BACKING BRAKE - RT .. 1

89 4510510 TEE W/O CLIP..................................................... 1

90 4510511 18” MALE/FEMALE BRAKE HOSE ..................... 1

91 4510518 HOSE CLIP.......................................................... 1

92 S-3409G SPRING CLAMP .................................................. 4

93 61243 202” BRAKELINE ................................................ 1

94 61217 94” BRAKELINE .................................................. 1

95 61213 6-1/2” BRAKELINE .............................................. 1

96 6234710 BRAKELINE CLIP BRACKET.............................. 1

97 3991012 ACTUATOR - INNER........................................... 1

98 61253 80” BRAKELINE .................................................. 1

99 65542-- OUTER HOUSING FOR UFP ACTUATOR ......... 1

100 7010168 CAP - PLASTIC OUTER MEMBER- 2” DIA ........ 1

101 5110394 DO-RAY JUMPER WIRE - 24” ............................ 2

102 0110080 7/16” X 1” HEX BOLT .......................................... 8

103 1310035 7/16” S/T LOCK WASHER ................................... 8

104 1410149 7/16” HEX FINISH NUT ....................................... 8

105 1310163 1.377 OD X .390 ID X .105 SPECIAL WASHER . 8

106 S-3501 RUBBER CUP WASHER .................................... 8

107 64603-- PONTOON RISER WELDMENT - TANDEM ....... 2

108 0310236 SUB 1/2” X 3-9/16” X 8” W/2” THREADS ............ 8

--- 7010169 LOCKOUT BRAKE SIDE MOUNT ....................... 1

DECALS:

-- 4850360 NMMA CERTIFIED TRAILER DECAL ................. 2

-- 4810709 TRAILER CAUTION & WARNING DECAL .......... 1

-- 4850218 TOON’R BY SHORELAND’R DECAL ................. 2

-- 4810501 LARGER SHORELAND’R DECAL ...................... 2

-- 4811334 GREASE ZERK ARROW DECAL ....................... 2

-- 4850184 DECAL FOR COATED UFP ACTUATOR ........... 1

-- 7010188 DECAL - PUSH BRKT UFP ACTUATOR ............ 1

ASSEMBLIES AND/OR OPTIONS:

64646-- PONTOON WINCH ASSEMBLY
65766 HARDWARE BAG
64014 14’ PONTOON BUNK
SS734 1-3/8” - 1-1/16” HUB & BEARING KIT
BK-4 1-3/8” - 1-1/16” BEARING KIT
64713-- AXLE ASSEMBLY - PONTOON
6238600 ROCKER BAG
65608-- TONGUE ASSEMBLY W/UFP ACTUATOR
SS1118 PONTOON RISER KIT - TANDEM AXLE
64604 HARDWARE BAG - PONTOON RISER KIT