ShoreLand'r LUVE22L User Manual
®
LUVE22L
ShoreLand’r offers its product line in painted nishes. When
ordering parts, it is important that you specify the nish or
color you have on your product. The 5-digit number along
with a 2-digit space _ _, note that the parts can be purchased
in various nishes.
03..........Black
39..........Galvanized w/Silver Plastic Components
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003908
REV A 02/04/2009
Page 1
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003908
REV A 02/04/2009
Page 2
the wire harness through the hole in the tongue cover plate.
(See Detail A) Secure the tongue cover plate in position with a 1/2”
X 1-1/2” hex bolt and 1/2” ange lock nut. Tighten. Plug the tongue
wire harness ends into the frame harnesses by matching colors
and ends. Push the extra wire into the rear of the tongue or remove
the grommets in the side frame and place the extra wire in the side
frame. Replace grommets just removed.
SAFETY CHAINS
Mount the safety chains to the front of the tongue by placing
a 3/8” at washer onto a 3/8” X 1-1/4” hex bolt, then insert the
bolt through the last link of the safety chain. Put the bolt through
the hole on one side of the tongue as shown. Place on another
at washer and secure with a 3/8” hex ange nut. Tighten. Repeat on the other chain on the other side of the tongue.
WINCH POST
Place the winch post assembly o n the tongue and secure
wi th thre e 3/ 8” X 4” h ex bolt s an d h ex flange lock n uts.
Place the nuts on the bolts but do not tighten because they
will have to be readjusted once the boat is on the trailer.
Remove the winch handle nut from the shaft. Align the hole in the
winch handle with the at surfaces on the shaft. Slide in position and
secure with the nut just removed. Tighten.
JACK
It is recommended that the jack be mounted on the right side of the
tongue. This will place it on the opposite side of the winch handle
to eliminate the possibility of the two interfering when being operated.
ASSEMBLY INSTRUCTIONS
Remove all items from the frame. Locate the hardware bag and sort
all items by size.
SWING TONGUE
The tongue comes shipped incorrectly in the frame. Slide the
tongue out from it’s shipping position and reinstall in the front
tongue channel. Line the holes in the tongue with the holes
in the tongue channel. Secure with a 1/2” X 4” hex bolt and
1/2” lock nut in the front cross hole.
Locate the coupler bag. Place the coupler on the end of the
tongue, align holes and secure with one 1/2” X 4” hex bolt and
hex ange lock nut in the rear coupler hole. Place two 1/2” X 1”
hex bolts into the front holes of the coupler and secure to the
each side of the tongue with 1/2” ange lock nuts. Tighten.
WIRE HARNESS
Locate the wire harness. Push the two triangular plugs in the hole
on the top of the tongue, then out the rear of the tongue. Place
Remove the hardware bag from the jack and sort all items by size.
Note that the jack mounting plate has only one pair of holes on one
side of the plate while the other side has holes punched to accommodate either 3”, 4”, or 5” tongue.
Place a 3/8” x 4” hex bolt into the single hole of the mounting plate
so the head of the bolt is on the jack side of the plate.
Once inserted, place one of the mounting channels onto the bolt so
the legs of the mounting channel are pointing away from the jack.
Place on a 3/8” lock washer and hex nut. Thread on only far enough
to secure in place.
Repeat the above process on the other single hole of the mounting
plate.
Place the jack on the tongue so that the two bolts just installed are on
the top side of the tongue with the jack on the right side of the tongue
and the mounting channels on the other side of the tongue.
Visually check which of the bottom three holes in the plate will align
just under the bottom side of the tongue. Insert the remaining two
3/8” x 4” hex bolts into these holes and then through the mating
holes in the mounting channel. Secure with 3/8” lock washers and
hex nuts.
Rotate the jack into the up position. Slide the jack forward or backward on the tongue to make sure it will not hit the frame of the trailer
when in the up position.
Tighten all of the mounting bolts to secure the jack assembly to the
tongue.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003908
REV A 02/04/2009
Page 3
Loading...